
R2-Backplane
Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

KiCAD source files for Manuvr's motion capture glove.
R2-Dev Backplane is an open-source printed circuit board by Manuvr, from the Manuvr/Digitabulum-Hardware repository on GitHub. It is a 4-layer board of 77.9 × 67.1 mm with 38 parts on 98 nets, routed with 829 tracks and 76 vias.
It is built around the EMIF02-USB03F2. Its parts include 15 connectors, 4 resistors, 4 ICs, 3 diodes and 2 switches.
This is a backplane PCB for Digitabulum. When combined with the PowerPlant, it has the same schematic as the r2-Backplane.
This board is intended as a testing harness for functional subunits designed for use with the Digitabulum sensor package. This would be the board you would want for prototyping new CPLD designs, power supplies, or compute modules.
If you do not want to do those things, but just want a working glove, you should use the r2-Backplane instead.
The CPLD GPIO pin has been routed to the 2v5/3v3 selection signal.
| Front | Back |
|---|---|
![]() | ![]() |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | r2Parts:CapArray_CKCL44 | CARY1, CARY2, CARY3 |
| 3 | LSF0204x | r2Parts:R-PUQFN-N12 | U2, U3, U4 |
| 2 | 1k | Resistors_SMD:R_0603 | R1, R4 |
| 2 | 680 | Resistors_SMD:R_0603 | R2, R3 |
| 2 | CONN_01X08 | Pin_Headers:Pin_Header_Straight_1x08_Pitch2.54mm | J2, J5 |
| 2 | MountingHole_2.2mm_M2_DIN965 | Mounting_Holes:MountingHole_2.2mm_M2_DIN965 | MH2, MH3 |
| 1 | 10k | r2Parts:RES_4_EXBN8V | RP2 |
| 1 | 10uF | Capacitors_SMD:C_0402_NoSilk | C1 |
| 1 | 22 | r2Parts:RES_4_EXBN8V | RP1 |
| 1 | Battery SW | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J10 |
| 1 | CHIP_PU | Buttons_Switches_SMD:SW_SPST_Panasonic_EVQPL_3PL_5PL_PT_A15 | SW4 |
| 1 | CONN_01X01 | manuvr_logo:ManuvrLogo | P3 |
| 1 | CONN_01X01 | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | P4 |
| 1 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J4 |
| 1 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05_Pitch2.54mm | J1 |
| 1 | CONN_02X15 | Pin_Headers:Pin_Header_Straight_2x15_Pitch2.54mm | J9 |
| 1 | Chrg | Resistors_SMD:R_0603_HandSoldering | D1 |
| 1 | Compute Socket | r2Parts:DF12(4.0)-30DS-0.5V(86) | P1 |
| 1 | Conn_02x12_Odd_Even | Pin_Headers:Pin_Header_Straight_2x12_Pitch2.54mm | J3 |
| 1 | EMIF02-USB03F2 | r2Parts:FCBGA12 | U1 |
| 1 | JTAG | Connect:IDC_Header_Straight_10pins | J8 |
| 1 | Li-Po | r2Parts:JST-Battery-Right-Angle | J7 |
| 1 | MH0 | Mounting_Holes:MountingHole_2.2mm_M2_DIN965 | MH0 |
| 1 | MH1 | Mounting_Holes:MountingHole_2.2mm_M2_DIN965 | MH1 |
| 1 | OPTS | Pin_Headers:Pin_Header_Straight_2x04_Pitch2.54mm | J11 |
| 1 | Pin_0 | Buttons_Switches_SMD:SW_SPST_Panasonic_EVQPL_3PL_5PL_PT_A15 | SW3 |
| 1 | Sensor Socket | r2Parts:DF12(3.0)-32DS-0.5V(86) | P2 |
| 1 | USB-MICRO-B | iansModules:USB_ZX62WRD-B-5PC | CON1 |
| 1 | Vcc0 | Resistors_SMD:R_0603_HandSoldering | D2 |
| 1 | Vcc1 | Resistors_SMD:R_0603_HandSoldering | D3 |

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.


Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.


Hanqaqa/Easyduino
Easily dive into different PCB KiCad designs of the most popular microcontroller devboards

murexrobotics/electrical
Highly integrated electronics design and printed circuit boards (PCBs) for the MATE ROV Competition. Attempt the impossible.


magnusnordlander/smart-lcc
A smarter LCC for the Lelit Bianca V2, with Wi-Fi and stuff.

Roboy/HTC_Vive_Sensors
Schematics and PCB designs for our custom Vive sensors based on a quad op-amp chip rather than discrete transistors.

sparkfun/SparkFun_RTK_Facet
The hardware and enclosure for the popular centimeter level RTK Facet GNSS receiver with built in display.

It measures 77.9 × 67.1 mm and has 4 copper layers, 1.6 mm thick.
38 parts, built around the EMIF02-USB03F2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Manuvr/Digitabulum-Hardware repository on GitHub, at the commit this page was made from: the board is r2-Dev-Backplane/r2-Dev-Backplane.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Manuvr before reusing the design.