
R2-Backplane
Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

KiCAD source files for Manuvr's motion capture glove.
IRQ TestHarness is an open-source printed circuit board by Manuvr, from the Manuvr/Digitabulum-Hardware repository on GitHub. It is a 4-layer board of 20.9 × 44.7 mm with 22 parts on 22 nets, routed with 276 tracks and 26 vias.
It is built around the 74HC165D. Its parts include 12 switches, 2 ICs and 2 connectors.
This is a backplane PCB for Digitabulum. When combined with the PowerPlant, it has the same schematic as the r2-Backplane.
This board is intended as a testing harness for functional subunits designed for use with the Digitabulum sensor package. This would be the board you would want for prototyping new CPLD designs, power supplies, or compute modules.
If you do not want to do those things, but just want a working glove, you should use the r2-Backplane instead.
The CPLD GPIO pin has been routed to the 2v5/3v3 selection signal.
| Front | Back |
|---|---|
![]() | ![]() |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | SW_PUSH_SMALL_H | Buttons_Switches_SMD:SW_SPST_Panasonic_EVQPL_3PL_5PL_PT_A15 | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10, SW11, SW12 |
| 4 | R_PACK4 | r2Parts:RES_4_EXBN8V | RP1, RP2, RP3, RP5 |
| 2 | 74HC165 | DHVQFN16-3.5x2.5 | U2, U3 |
| 1 | CAPARRAY_4 | r2Parts:CapArray_CKCL44 | CARY1 |
| 1 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05_Pitch2.54mm | P1 |
| 1 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05_Pitch1.27mm | P2 |
| 1 | R_PACK4 | Buttons_Switches_SMD:SW_DIP_x4_W5.08mm_Slide_Copal_CHS-A | RP4 |

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.


Manuvr/Digitabulum-Hardware
KiCAD source files for Manuvr's motion capture glove.

shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

slu4coder/Minimal-64x4-Home-Computer
My DIY TTL home computer with VGA and PS/2 and 4x the processing power of a Commodore C64 or Apple II.

slu4coder/Minimal-UART-Computer-1-2
Legacy: Version 1 and 2 of my TTL-only CPU featuring UART I/O, an expansion port, 512KB SSD at up to 10MHz clock speed


westlicht/performer-hardware
PER|FORMER Eurorack Sequencer - Hardware Design Files

slu4coder/Minimal-64-Home-Computer
Legacy: Full TTL-only home computer with VGA and PS/2 and twice the processing power of a Commodore 64


It measures 20.9 × 44.7 mm and has 4 copper layers, 1.6 mm thick.
22 parts, built around the 74HC165D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Manuvr/Digitabulum-Hardware repository on GitHub, at the commit this page was made from: the board is SmallTools/IRQ-TestHarness.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Manuvr before reusing the design.