
DB19 IDC20
lampmerchant/tashtwenty
An interface for the DCD protocol used by Apple's Hard Disk 20.

An interface for the DCD protocol used by Apple's Hard Disk 20.
TashTwenty Tiny is an open-source printed circuit board by lampmerchant, from the lampmerchant/tashtwenty repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 56.6 × 57.7 mm with 31 parts on 30 nets, routed with 510 tracks and 28 vias.
It is built around the 74ACT08SC and BC337. Its parts include 14 resistors, 4 capacitors, 3 ICs, 3 connectors and 2 diodes. It belongs with the retro computing and games boards and the PIC boards of this library.
This is a dual PCB design, using mostly through hole components (with the exeption of the SD connector). It's designed this way to be period correct and easy to build for people who don't like soldering SMT components
This folder contains the source KiKad files for the main board. Please check the DB19_IDC20 subfolder for the DB19 to IDC20 adapter.
Here is the BOM for the main board. Part number are what was tested on prototypes board but you may find alternatives easily, especially resistors and sockets
| Reference(s) | Value | Quantity | Notes | Part number |
|---|---|---|---|---|
| C1, C2 | 2.2uF | 2 | radial electrolytic capacitors 4x1.5mm | Jamicon SHR2R2M1HC07M |
| C3, C4 | 100nF | 2 | ceramic capacitor 5.08mm | Weltron 453358 |
| D1 | Green | 1 | 5mm green LED | Kingbright L-53SGD |
| D2 | Yellow+Red | 1 | 5mm dual color common cathode LED | Kingbright L-59EYW |
| J1 | SD Card | 1 | SD Card connector | TE 2041021-1 |
| J2 | IDC20 | 1 | IDC 2x10 Header | BLK 10120560 |
| Q1 | BC337 | 1 | NPN BJT Transistor | BC337 |
| R10, R11 | 330Ω | 2 | standard 0.25W carbon film resistor | TRU TC-CFR0W4J0331 |
| R1, R3, R5, R8 | 1200Ω | 4 | standard 0.25W carbon film resistor | TRU TC-CFR0W4J0122 |
| R2, R4, R6 | 2200Ω | 3 | standard 0.25W carbon film resistor | TRU TC-CFR0W4J0222 |
| R7, R9, R12, R13, R14 | 10kΩ | 5 | standard 0.25W carbon film resistor | TRU TC-CFR0W4J0103 |
| U1 | PIC16F1704 | 1 | PIC 8-bit Microcontroller (DIP-14) | PIC16F1704-I/P |
| U2 | 74ACT08 | 1 | Quad TTL 2-Input AND Gate | SN74ACT08N |
| U3 | 3.3V LDO | 1 | 3.3V LDO voltage regulator | MCP1700-3302E/TO |
Optional
| Reference(s) | Value | Quantity | Notes | Part number |
|---|---|---|---|---|
| J1 | - | 1 | 1x2 header + jumper or wire | - |
| U1, U2 | socket | 2 | DIP-14 socket | TRU 14-LC-TT |
| Case | ABS | 1 | Instrument Case, ABS 2.6x2.6" | HM 1593K(TBU|GY|BK) |
Using sockets is recommended because it will allow you to reclaim the gates and microcontroler if your board is broken. This will also allow you to upgrade the firmware if a future firmware is released.
Bridging J3 connects the !ENBL pin on the microcontroller to the !ENBL pin on the 2x20 header, which is what you want for the overwhelming majority of cases where you're connecting the board to an external/secondary floppy drive port that has !ENBL2 in the connector where it should be. It's fine to bridge the two pins with a piece of wire, but if you want this expandability available to you, it'd be better to solder a two-pin header and stick a jumper on it when not in use. The pin closest to the center of the board is the one connected to the microcontroller.
This is a matching board for TashTwenty. Please use this one to avoid any damage to your computer or TashTwenty. Others adapters boards are wired differently
| Reference(s) | Value | Quantity | Notes | Part number |
|---|---|---|---|---|
| J1 | IDC20 | 1 | IDC 2x10 Header | BLK 10120560 |
| J2 | DB19 | 1 | DB19 wire male connector | Good luck. |
Here is a mouser link (without the case):
Here us a digikey (without the case):
You need a cable to connect both boards Any straight IDC-20 cable should work (pin 1 to pin 1, etc). Macintosh floppy cables are compatible. We used a few Apple cables for prototyping:
If you are looking for a new one, a compatible assembly is made buy Advantech under the part number PCL-10120-1E.
the PCBs are simple 2 layers boards. The gerbers are avaible in the release section. Check for the following files:
You should be use any mainstream PCB manufacturer for theses. Nothing special about them. PCB thickness should FR-4 with a 1.6mm thickness On JLCPCB, select "Specify a location" to the option "Remove Order Number"
Building is straightworfard. It's recommended to start with the SD Card connector, then components, and headers + sockets last.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7, R9, R12, R13, R14 |
| 4 | 1200 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3, R5, R8 |
| 3 | 2200 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4, R6 |
| 3 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3 |
| 2 | 100nF | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C3, C4 |
| 2 | 2.2uF | Capacitor_THT:CP_Radial_D4.0mm_P1.50mm | C1, C2 |
| 2 | 330 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10, R11 |
| 1 | 74ACT08 | Package_DIP:DIP-14_W7.62mm | U2 |
| 1 | BC337 | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | IDC20 | Connector_IDC:IDC-Header_2x10_P2.54mm_Vertical | J2 |
| 1 | LED | LED_THT:LED_D5.0mm_Horizontal_O3.81mm_Z3.0mm | D1 |
| 1 | LED_Dual_ACA | LED_THT:LED_D5.0mm-3_Horizontal_O3.81mm_Z3.0mm | D2 |
| 1 | MCP1700-3302E_TO92 | Package_TO_SOT_THT:TO-92_Inline | U3 |
| 1 | PIC16F1825-IP | Package_DIP:DIP-14_W7.62mm | U1 |
| 1 | SD_Card | Connector_Card:SD_TE_2041021 | J1 |
The 30 most common of 31 parts.

lampmerchant/tashtwenty
An interface for the DCD protocol used by Apple's Hard Disk 20.

Mathesar/14mhz-accelerator
14MHz 68000 accelerator with 1MB fast ram for amiga 500


roarfred/AmsToMqttBridge
Minimalistic system to read AMS/HAN data from electrical meter



leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

pablozg/freeds
Derivador de energía solar excedente creado por Pablo Zerón, Diseño PCB por Amcalo, Tester original por Aeizoon, Wiki por Zoilo Mora

CTXz/Video-Glitch-Array
A collection of glitch art circuits dedicated to VGA signal manipulation
It measures 56.6 × 57.7 mm and has 2 copper layers, 1.6 mm thick.
31 parts, built around the 74ACT08SC and BC337. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the lampmerchant/tashtwenty repository on GitHub, at the commit this page was made from: the board is pcb/TashTwenty Tiny/TashTwenty Tiny.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).