

DFTBoard
An 8-layer board in Kicad built upon Xilinx Zynq Chip. Includes sound output, HDMI, DDR3, and Arduino Uno style header for screen connection
- Size
- 120 × 60 mm
- Copper layers
- 8
- Thickness
- 1.6 mm
- Parts
- 299
- Nets
- 302
- Pads
- 1,615
- Tracks, vias
- 12,613, 964
- Pours
- 23
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 19 Feb 2021
- Updated
- 6 Nov 2021
Overview
DFTBoard is an open-source printed circuit board by juliancoy, from the juliancoy/zynqPCB repository on GitHub, published under the MIT licence. It is an 8-layer board of 120 × 60 mm with 299 parts on 302 nets, routed with 12,613 tracks and 964 vias.
It is built around the TLV320AIC3104EVM, APDS-9960 and S25FL256SAGNFI001, with the VL53L1CXV0FY/1, LM3880-1AC and MT41K256M16HA-125:E TR among its other parts. Its parts include 129 capacitors, 106 resistors, 23 ICs, 10 transistors and 9 connectors. It belongs with the fPGA and programmable logic boards and the AVR (ATmega, ATtiny) and FPGA and CPLD boards of this library.
Main components
12TLV320AIC3104EVM
-- V-Audio Modules ROHSTexas InstrumentsV-Audio ModulesAPDS-9960
LGA-8LGA-8 Abolished Device ROHSBroadcom LimitedAmbient Light SensorsS25FL256SAGNFI001
WSON-8-EP(6x8)-40℃~+85℃ 100,000 cycles 130ms@(64KB) 133MHz 2.7V~3.6V 20 Years 256Mbit 340us 70uA SPI WSON-8-EP(6x8) NOR FLASH ROHSInfineon TechnologiesNOR FLASHVL53L1CXV0FY/1
LGA-12(2.5x4.9)-20℃~+85℃ 1.56mm 16mA 2.5mm 2.6V~3.5V 4.9mm 4m I2C Programmable transmission Yes LGA-12(2.5x4.9) Position Sensors ROHSSTMicroelectronicsPosition SensorsLM3880-1AC
SOT23-6Simple Power Sequencer, Power UP : 1 2 3, Power Down 3 2 1, Timing Designator 60msTexas InstrumentsUncategorisedMT41K256M16HA-125:E TR
96-FBGA (9x14)96-FBGA (9x14) SDRAM ROHSMicron TechSDRAMLIS2HH12
LGA-12(2x2)-40℃~+85℃ 1.71V~3.6V 16bit 5uA Accelerometer SPI、I2C X,Y,Z ±8g LGA-12(2x2) Accelerometers ROHSSTMicroelectronicsAccelerometersMIC2025-1YMM
MSOP-8-40℃~+85℃ 1 2.7V~5.5V 500mA 90mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Undervoltage Protection(UVP)、Over Temperature Protection MSOP-8 Power Distribution Switches ROHSMicrochip TechnologyPower Distribution SwitchesPCA9306D
SO-8-40℃~+105℃ 1 1.8V~5.5V 1V~3.6V 2 2Mbps Automatic direction detection、Output enable high-impedance Bidirectional Level translator Open-drain SMBus、I2C SO-8 Translators, Level Shifters ROHSNXP SemiconductorsTranslators, Level ShiftersTPS51200DRCR
VSON-10-EP(3x3)-40℃~+85℃@(TA) 1 1mA 2.375V~3.5V Adjustable Buck Built-in Overcurrent Protection、Output discharge、Operating status indication、Output voltage tracking Step-down type VSON-10-EP(3x3) Power Management - Specialized ROHSTexas InstrumentsPower Management - SpecializedTSOP34438
插件,P=2.54mm-25℃~+85℃ 2.5V~5.5V 350uA 38kHz 45m 45° 插件,P=2.54mm Infrared Remote Receiver (IRM) ROHSVishay IntertechnologyInfrared Remote Receiver (IRM)XC7Z020CLG484
UncategorisedXILINX
README
README.mdzynqPCB
An 8-layer board built upon Xilinx Zynq Chip. Includes sound output, HDMI, DDR3, USB Host, USB Device, a handful of sensors, and Arduino Uno style header for screen connection. See schematic in this repo "schematic.pdf"
OPEN TO COLLABORATION!!
Kicad Project
https://kicad.org/
3D Render
Layout
Block Diagram

Manufactured PCB - Top

Manufactured PCB - Bottom

Introduction
Hi friends! This is the current status of my 4-year project to make an FPGA-accelerated audio+video synthesizer. I am currently taking a hiatus from this project, and have decided to make the entire PCB design available on Github! Quite a bit of work has been put into this project. The difficult tasks of part selection and routing have been taken care of. I am still testing the functionality of the board. Only one PCB problem has been found: the SPI Flash for Zynq Boot was the wrong footprint! This problem has since been fixed.
I believe that together we can make this a formidable tool in the open hardware community.
The following software projects need to be undertaken before this project is usable by the general public:
- Development of Boot firmware for the SPI flash which loads the linux kernel from the SD card
- Development of a basic shell block diagram in Vivado
If you embark on one of these projects, please share your code here so other engineers don't have to reproduce your work :)
IMPORTANT: Make sure to clone the following into the same directory:
https://github.com/julianfl0w/footprints.pretty
https://github.com/julianfl0w/lib
I make no guarantees as to device funtionality. Please review the board carefully before production.
Specific hardware (from BOM)
xc7z020clg484 (Zynq Chip)
VL53L1CXV0FY/1 (rangefinder)
Interfaces:
- JTAG interface : Functional!
- SPI Flash : Untested
- VL53L1CXV0FY Rangefinder : Untested
- APDS-9960 Rangefinder : Untested
- LIS2HH12 Accelerometer : Untested
- LSM6DSLTR IMU : Untested
- HDMI Out : Untested
- USB Host : Untested
- USB Device : Untested
- DDR3 PS Memory : Untested
- TLV320 Audio Codec : Untested
- MicroSD card : Untested
Parts
299| Qty | Value | Footprint | References |
|---|---|---|---|
| 29 | .47uF | Capacitor_SMD:C_0402_1005Metric | C1, C14, C15, C17, C18, C23, C101, C102, C103, C104, C108, C116, C117, C118, C119, C121 +13 |
| 25 | .1uF | Capacitor_SMD:C_0402_1005Metric | C16, C36, C39, C52, C53, C56, C62, C63, C64, C68, C70, C71, C72, C77, C107, C131 +9 |
| 23 | 40.2 1% | Resistor_SMD:R_0402_1005Metric | R51, R52, R53, R54, R55, R56, R57, R58, R59, R60, R61, R62, R63, R64, R65, R66 +7 |
| 18 | 10uF | Capacitor_SMD:C_0603_1608Metric | C2, C3, C10, C11, C13, C26, C33, C41, C51, C54, C58, C125, C126, C128, C129, C130 +2 |
| 18 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C5, C19, C20, C21, C24, C27, C42, C57, C59, C66, C83, C100, C114, C115, C122, C127 +2 |
| 12 | 100k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5, R17, R27, R28, R29, R34, R81, R101 |
| 10 | 100 | Resistor_SMD:R_0402_1005Metric | R11, R12, R13, R14, R15, R16, R19, R20, R22, R23 |
| 10 | IRLML2502 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10 |
| 9 | 100uF | Capacitor_SMD:C_1210_3225Metric | C6, C12, C25, C28, C67, C73, C74, C99, C123 |
| 9 | 20k | Resistor_SMD:R_0402_1005Metric | R25, R91, R92, R93, R94, R95, R96, R97, R106 |
| 9 | 4.7k | Resistor_SMD:R_0402_1005Metric | R8, R9, R10, R74, R82, R83, R98, R103, R104 |
| 8 | .01uF | Capacitor_SMD:C_0402_1005Metric | C93, C98, C105, C106, C109, C110, C111, C120 |
| 8 | 150 | Resistor_SMD:R_0402_1005Metric | R21, R24, R35, R45, R78, R80, R86, R102 |
| 8 | 1uF | Capacitor_SMD:C_0402_1005Metric | C37, C38, C40, C43, C44, C45, C91, C92 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R6, R33, R36, R39, R42, R43, R44 |
| 5 | BLUE LED | Capacitor_SMD:C_0603_1608Metric | D3, D4, D5, D6, D7 |
| 4 | 18pF | Capacitor_SMD:C_0402_1005Metric | C75, C76, C84, C85 |
| 4 | 1k | Resistor_SMD:R_0402_1005Metric | R77, R79, R85, R105 |
| 4 | 2.2uH | Capacitor_SMD:C_1812_4532Metric | L1, L2, L3, L4 |
| 4 | 49.9k | Resistor_SMD:R_0402_1005Metric | R18, R30, R31, R32 |
| 3 | .05 | Resistor_SMD:R_2512_6332Metric | R88, R89, R90 |
| 3 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C35, C69, C80 |
| 3 | 240 1% | Resistor_SMD:R_0402_1005Metric | R7, R46, R49 |
| 3 | 47 | Resistor_SMD:R_0402_1005Metric | R26, R84, R87 |
| 3 | 47uF | Capacitor_SMD:C_0805_2012Metric | C7, C32, C61 |
| 3 | 80.6 1% | Resistor_SMD:R_0402_1005Metric | R50, R75, R76 |
| 3 | AUDIO JACK | DFTcustom:RA49C14B | J2, J3, J4 |
| 2 | 10k 1% | Resistor_SMD:R_0402_1005Metric | R47, R48 |
| 2 | 1M | Resistor_SMD:R_0402_1005Metric | R37, R40 |
| 2 | 220uF Tant. | Capacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-T | C48, C49 |
| 2 | 24.000MHZ | ABM3-12.000MHZ-B2-T:XTAL500X320X130N | Y1, Y2 |
| 2 | 8.06k 1% | Resistor_SMD:R_0402_1005Metric | R38, R41 |
| 2 | LED_RGB | DFTcustom:PLCC6-SM-RGB-LED | D1, D2 |
| 2 | LM3880 | Package_TO_SOT_SMD:SOT-23-6 | U1, U2 |
| 2 | MT41K256M16HA-125_E | DFTcustom:FBGA-96-DDR3-SDRAM | U15, U16 |
| 2 | USB3320 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U10, U12 |
| 1 | 120R, 100 MHz, size 0603 | Capacitor_SMD:C_0603_1608Metric | FB1 |
| 1 | 24.9 1% | Resistor_SMD:R_0402_1005Metric | R100 |
| 1 | 330uF | Capacitor_SMD:C_1206_3216Metric | C22 |
| 1 | 47k | Resistor_SMD:R_0402_1005Metric | R99 |
| 1 | 47uF | Capacitor_SMD:C_1210_3225Metric | C113 |
| 1 | ABRACON-ASDMB | XTAL_ASDMB-24.000MHZ-LC-T:XTAL_ASDMB-24.000MHZ-LC-T | U18 |
| 1 | APDS-9960 | DFTcustom:APDS_9960 | U14 |
| 1 | AVR-JTAG-10 | DFTcustom:XilinxJTAG | CON1 |
| 1 | Arduino_Uno_Shield_Simplified | DFTcustom:Arduino_Uno_Shield_Simplified | XA1 |
| 1 | FTDITypeUART | DFTcustom:FTDI_CONN | U17 |
| 1 | GNDTIE | DFTcustom:gndtie | GT1 |
| 1 | HDMI_A | DFTcustom:10029449-111RLF | J9 |
| 1 | JACK_TRS_4PINS | DFTcustom:SJ-352X-SMT | J5 |
| 1 | LIS2HH12 | Package_LGA:LGA-12_2x2mm_P0.5mm | U6 |
| 1 | LSM6DSLTR | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U23 |
| 1 | MEMSMIC | SPW2430HR5H-B:MIC_SPW2430HR5H-B | MIC1 |
| 1 | MIC2025-1YMM | SOP65P490X110-8N:SOP65P490X110-8N | U11 |
| 1 | Micro_SD_Card_Det | DFTcustom:AMPHENOL-114-00841-68 | J8 |
| 1 | PCA9306 | Package_SO:SSOP-8_2.95x2.8mm_P0.65mm | U21 |
| 1 | S25FL256SAGNFI001 | footprints:Cypress-002-18827-0-0-0 | U19 |
| 1 | SC189 - 1.0V | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | SC189 - 1.8V | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | SC189 - 3.3V | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | TL6215RF200BDT | DFTcustom:tl6215_right_angle | SW1 |
| 1 | TLV320AIC3104 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.65x3.65mm | U9 |
| 1 | TLV62080DSGx | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U5 |
| 1 | TPS51200DRCR | Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.65x2.4mm_ThermalVias | U8 |
| 1 | TSOP344 | DFTcustom:JUMPER_3PIN | U22 |
| 1 | USB_A | DFTcustom:USB-A-Receptacle-FCI_87583 | J6 |
| 1 | USB_B | Connector_USB:USB_B_OST_USB-B1HSxx_Horizontal | J7 |
| 1 | VL53L1CXV0FY/1 | DFTcustom:Optical_LGA12 | U13 |
| 1 | xc7z020clg484 | DFTcustom:BGA-484_19.0x19.0mm_Layout22x22_P0.80mm_dia0.40mm | U20 |
The 295 most common of 299 parts.
Similar boards
- 8 layers120 × 65.6 mm

- 8 layers110.3 × 59.1 mm

DFTBoard
SunnyYoshimitsu/CelestiCall
An attempt at making a somewhat modern smartphone with many functions.
313 parts1 - 12 layers92 × 92 mm

- 6 layers139.7 × 88.9 mm

- 6 layers55 × 95 mm

- 4 layers100 × 115.2 mm

- 4 layers58.4 × 68.6 mm

- 4 layers210 × 125 mm

Questions
How big is the DFTBoard PCB?
It measures 120 × 60 mm and has 8 copper layers, 1.6 mm thick.
What parts does the DFTBoard use?
299 parts, built around the TLV320AIC3104EVM, APDS-9960, S25FL256SAGNFI001 and VL53L1CXV0FY/1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DFTBoard KiCad files?
From the juliancoy/zynqPCB repository on GitHub, at the commit this page was made from: the board is DFTBoard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DFTBoard design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).