

ArdUnoTester
Some arduino code
- Size
- 122 × 110 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 52
- Pads
- 122
- Tracks, vias
- 143, 0
- Pours
- 87
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 15 Dec 2014
- Updated
- 15 Aug 2025
Overview
ArdUnoTester is an open-source printed circuit board by jonsag, from the jonsag/miscArduino repository on GitHub. It is a 2-layer board of 122 × 110 mm with 48 parts on 52 nets, routed with 143 tracks and 0 vias.
It is built around the ARDUINO UNO R3. Its parts include 20 resistors, 20 diodes and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
1README
README.mdmiscArduino
Some arduino code
avrdude
Uploading
Upload to ATmega2560
$ avrdude avrdude -v -q -p m2560 -c wiring -P /dev/ttyUSB0 -D -U flash:w:/path/to/image.hex:i
Upload to ATmega328 (Uno etc.)
$ avrdude -p m328p -c usbtiny -P /dev/ttyUSB0 -U flash:w:firmware.hex
Programmer / Chip Verification
$ avrdude -c usbtiny -p m168
If you see a 'Reading' progress bar, a device signature, and some other text, your settings are correct
Cheat sheets
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 220R | My_Misc:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal_larger_pads | R1, R2, R3, R4, R5, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20 +4 |
| 20 | LED | My_Misc:LED_D5.0mm_large | D1, D2, D3, D4, D5, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20 +4 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 1 | Arduino_UNO_R3 | My_Arduino:Arduino_UNO_R3_shield_large | A1 |
| 1 | Power In | My_Parts:2-pole_power_in_screw_terminal | U1 |
| 1 | Rx | My_Parts:Jumper_1x02_P2.54mm_large | JP2 |
| 1 | Tx | My_Parts:Jumper_1x02_P2.54mm_large | JP1 |
More from jonsag/miscArduino
8- 2 layers142.2 × 125.7 mm

- 2 layers143.5 × 114.3 mm

- 2 layers74 × 84 mm

- 2 layers88.9 × 111.8 mm

- 2 layers76.8 × 52.7 mm

- 2 layers112 × 40 mm

- 2 layers

- 2 layers76.8 × 31.8 mm

Similar boards
- 2 layers68.8 × 53.6 mm

Relatively Universal ROM Programmer
AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.
149 parts257GPL-3.0 - 2 layers69.1 × 53.8 mm

Motor controller
AlanFord/self-balancing-stick
Dual Axis Reaction Wheel Inverted Pendulum
25 parts79MIT - 2 layers68.6 × 53.3 mm

Protogasm Board V2
Edging-Machines/Edging-Machines
This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.
14 parts67MIT - 2 layers53.8 × 69.6 mm

EVSE V2 2
PedroCNeves/AC_ChargingStation
A learning project to create an EV AC Charging station based on an Arduino Uno
32 parts50 - 2 layers113.7 × 61 mm

ArduTester SMD
jonsag/arduTester
An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4
17 parts14 - 4 layers65.9 × 52.9 mm

- 4 layers68.6 × 53.3 mm

101 PCB
ICRS/101
The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.
89 parts10CC-BY-4.0 - 2 layers53.3 × 68.3 mm

Questions
How big is the ArdUnoTester PCB?
It measures 122 × 110 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ArdUnoTester use?
48 parts, built around the ARDUINO UNO R3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ArdUnoTester KiCad files?
From the jonsag/miscArduino repository on GitHub, at the commit this page was made from: the board is ardUnoTester/ardUnoTester.kicad_pcb and its schematic ATmega328-test-rig/ATmega328-test-rig.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ArdUnoTester design in my own project?
Its repository states no licence, so its author keeps all rights: ask jonsag before reusing the design.