Skip to the content
2 layers143.5 × 114.3 mmArdTester SMD, the printed circuit board in 3D

ArdTester SMD

jonsag/miscArduino

Some arduino code

Size
143.5 × 114.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
54
Nets
69
Pads
220
Tracks, vias
585, 35
Pours
217
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
15 Dec 2014
Updated
15 Aug 2025

Overview

ArdTester SMD is an open-source printed circuit board by jonsag, from the jonsag/miscArduino repository on GitHub. It is a 2-layer board of 143.5 × 114.3 mm with 54 parts on 69 nets, routed with 585 tracks and 35 vias.

It is built around the ARDUINO UNO R3. Its parts include 22 resistors, 22 diodes, 3 ICs and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

miscArduino

Some arduino code

avrdude

Uploading

Upload to ATmega2560

$ avrdude avrdude -v -q -p m2560 -c wiring -P /dev/ttyUSB0 -D -U flash:w:/path/to/image.hex:i

Upload to ATmega328 (Uno etc.)

$ avrdude -p m328p -c usbtiny -P /dev/ttyUSB0 -U flash:w:firmware.hex

Programmer / Chip Verification

$ avrdude -c usbtiny -p m168

If you see a 'Reading' progress bar, a device signature, and some other text, your settings are correct

Cheat sheets

https://github.com/amirbawab/AVR-cheat-sheet

Parts

54
QtyValueFootprintReferences
22220RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22 +6
22LEDLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1, D2, D3, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22 +6
4MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
1Arduino_Mini_ProMy_Arduino:Arduino_Pro_Mini_vA_sides_n_A4-A7_largeU3
1Arduino_Mini_ProMy_Arduino:Arduino_Pro_Mini_vC_no-progr-largeU1
1Arduino_Nano_v3.xMy_Arduino:Arduino_Nano_WithMountingHoles_largerA2
1Arduino_UNO_R3My_Arduino:Arduino_UNO_R3_shield_largeA1
1Power InMy_Parts:2-pole_power_in_screw_terminalU2
1SW_DIP_x02Button_Switch_THT:SW_DIP_SPSTx02_Slide_6.7x6.64mm_W7.62mm_P2.54mm_LowProfileSW1

More from jonsag/miscArduino

8
  • 2 layers142.2 × 125.7 mmArdTester, the printed circuit board in 3D

    ArdTester

    jonsag/miscArduino

    Some arduino code

    66 parts
  • 2 layers88.9 × 111.8 mmArdMiniProTester, the printed circuit board in 3D

    ArdMiniProTester

    jonsag/miscArduino

    Some arduino code

    48 parts
  • 2 layers122 × 110 mmArdUnoTester, the printed circuit board in 3D

    ArdUnoTester

    jonsag/miscArduino

    Some arduino code

    48 parts
  • 2 layers76.8 × 52.7 mmArdFilaSplice, the printed circuit board in 3D

    ArdFilaSplice

    jonsag/miscArduino

    Some arduino code

    19 parts
  • 2 layers112 × 40 mmArdPWMSoftStart, the printed circuit board in 3D

    ArdPWMSoftStart

    jonsag/miscArduino

    Some arduino code

    17 parts
  • 2 layers76.8 × 31.8 mmArdDice, the printed circuit board in 3D

    ArdDice

    jonsag/miscArduino

    Some arduino code

    9 parts

Similar boards

  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0
  • 2 layers69.1 × 53.8 mmMotor controller, the printed circuit board in 3D

    Motor controller

    AlanFord/self-balancing-stick

    Dual Axis Reaction Wheel Inverted Pendulum

    25 parts79MIT
  • 2 layers68.6 × 53.3 mmProtogasm Board V2, the printed circuit board in 3D

    Protogasm Board V2

    Edging-Machines/Edging-Machines

    This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

    14 parts67MIT
  • 2 layers53.8 × 69.6 mmEVSE V2 2, the printed circuit board in 3D

    EVSE V2 2

    PedroCNeves/AC_ChargingStation

    A learning project to create an EV AC Charging station based on an Arduino Uno

    32 parts50
  • 2 layers113.7 × 61 mmArduTester SMD, the printed circuit board in 3D

    ArduTester SMD

    jonsag/arduTester

    An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4

    17 parts14
  • 4 layers65.9 × 52.9 mmMotor shield, the printed circuit board in 3D

    Motor shield

    DCC-EX/EX-MotorShield8874

    Design files for the open source 5A Motor Shield

    114 parts12
  • 4 layers68.6 × 53.3 mm101 PCB, the printed circuit board in 3D

    101 PCB

    ICRS/101

    The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.

    89 parts10CC-BY-4.0
  • 2 layers53.3 × 68.3 mmAnac 2040, the printed circuit board in 3D

    Anac 2040

    rallekralle11/Anna2040

    RP2040-based board in the shape of the Arduino uno

    63 parts9

Questions

How big is the ArdTester SMD PCB?

It measures 143.5 × 114.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ArdTester SMD use?

54 parts, built around the ARDUINO UNO R3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ArdTester SMD KiCad files?

From the jonsag/miscArduino repository on GitHub, at the commit this page was made from: the board is ardTester-SMD/ardTester-SMD.kicad_pcb and its schematic ATmega328-test-rig/ATmega328-test-rig.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ArdTester SMD design in my own project?

Its repository states no licence, so its author keeps all rights: ask jonsag before reusing the design.