

ATmega328base SMD
Some arduino code
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 17
- Nets
- 36
- Pads
- 82
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Dec 2014
- Updated
- 15 Aug 2025
Overview
ATmega328base SMD is an open-source printed circuit board by jonsag, from the jonsag/miscArduino repository on GitHub. It is a 2-layer board with 17 parts on 36 nets.
It is built around the ATMEGA328P-AU and AMS1117-5.0S. Its parts include 5 capacitors, 4 resistors, 3 connectors, 2 ICs and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)AMS1117-5.0S
SOT-891 1.3V@(1A) 12V 5V 60dB@(120Hz) Fixed Over Current Protection Positive SOT-89 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdmiscArduino
Some arduino code
avrdude
Uploading
Upload to ATmega2560
$ avrdude avrdude -v -q -p m2560 -c wiring -P /dev/ttyUSB0 -D -U flash:w:/path/to/image.hex:i
Upload to ATmega328 (Uno etc.)
$ avrdude -p m328p -c usbtiny -P /dev/ttyUSB0 -U flash:w:firmware.hex
Programmer / Chip Verification
$ avrdude -c usbtiny -p m168
If you see a 'Reading' progress bar, a device signature, and some other text, your settings are correct
Cheat sheets
Parts
17| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 22p | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3 |
| 2 | 5k1 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R4 |
| 1 | 100n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4 |
| 1 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 10u | Capacitor_SMD:CP_Elec_5x5.4 | C5 |
| 1 | 16MHz | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | 22u | Capacitor_SMD:CP_Elec_4x5.3 | C1 |
| 1 | 2x3_ISP_header | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical_SMD | J1 |
| 1 | 330R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
| 1 | AMS1117-5_0 | Package_TO_SOT_SMD:SOT-223 | U1 |
| 1 | ATMEGA328P-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U2 |
| 1 | FTDI | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical_SMD_Pin1Left | J3 |
| 1 | FTDI Power | Button_Switch_SMD:SW_DIP_SPSTx01_Slide_6.7x4.1mm_W6.73mm_P2.54mm_LowProfile_JPin | JP1 |
| 1 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4135-GF-A_6P_TopMnt_Horizontal | J4 |
More from jonsag/miscArduino
8- 2 layers142.2 × 125.7 mm

- 2 layers143.5 × 114.3 mm

- 2 layers74 × 84 mm

- 2 layers88.9 × 111.8 mm

- 2 layers122 × 110 mm

- 2 layers76.8 × 52.7 mm

- 2 layers112 × 40 mm

- 2 layers76.8 × 31.8 mm

Similar boards
- 2 layers161.4 × 88 mm

- 2 layers30.5 × 12.7 mm

- 4 layers100 × 70 mm

SEM
Serhio4522/SEM_hitachi-
Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.
288 parts1 - 2 layers77 × 39 mm

- 2 layers80 × 110 mm

NucDeck Left Controller PCB
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!
59 parts561CERN-OHL-S-2.0 - 2 layers50.5 × 128.5 mm

- 2 layers152 × 88 mm

RFBitBangSMT
profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance
271 parts222 - 2 layers50.2 × 31.2 mm

MCU Datalogger
futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.
31 parts138MIT
Questions
What parts does the ATmega328base SMD use?
17 parts, built around the ATMEGA328P-AU and AMS1117-5.0S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ATmega328base SMD KiCad files?
From the jonsag/miscArduino repository on GitHub, at the commit this page was made from: the board is ATmega328base-SMD/ATmega328base-SMD.kicad_pcb and its schematic ATmega328-test-rig/ATmega328-test-rig.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ATmega328base SMD design in my own project?
Its repository states no licence, so its author keeps all rights: ask jonsag before reusing the design.