

Cruz FlightComputerPCB
2-layer KiCad flight computer PCB integrating Arduino Nano, MPU6050 IMU, BMP280 altimeter, and dual-servo control with regulated 3.3V power and isolated servo power.
- Size
- 48 × 41.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 14
- Nets
- 50
- Pads
- 78
- Tracks, vias
- 71, 71
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 13 Sep 2026
- Updated
- 13 Sep 2026
Overview
Cruz FlightComputerPCB is an open-source printed circuit board by heallyc, from the heallyc/FRL-NMP-flight-computer repository on GitHub. It is a 2-layer board of 48 × 41.3 mm with 14 parts on 50 nets, routed with 71 tracks and 71 vias.
It is built around the BMP280 and MPU-6050. It belongs with the sensors and measurement and robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdFRL-NMP-flight-computer
2-layer KiCad flight computer PCB integrating Arduino Nano, MPU6050 IMU, BMP280 altimeter, and dual-servo control with regulated 3.3V power and isolated servo power.
Designed a 2-layer KiCad PCB integrating an Arduino Nano, MPU6050 IMU, BMP280 altimeter, and dual-servo control; designed 3.3V power regulation, I²C pull-ups, decoupling, ground planes, isolated servo power, and signal routing; completed ERC/DRC verification and generated fabrication files, BOM, schematic, and 3D renders.
Parts
14| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | TestPoint | TestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | 3V3, 5V_USB1, GND, SCL1, SDA1, SERVO_5V1 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | M3A, M3B |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano | A1 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | BMP280 |
| 1 | Conn_02x03 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J1 |
| 1 | LOGO | LOGO | G*** |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | MPU6050 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | Screw Header |
Similar boards
- 2 layers115 × 115 mm

- 4 layers45 × 89 mm

- 2 layers50 × 63 mm

Zenith Development Board
zenitheesc/Zenith-Development-Board
The Zenith Development Board was developed to serve as a first project for the new members of the group.
69 parts3MIT - 2 layers96.6 × 100 mm

- 4 layers62.2 × 54.6 mm

Flight ControllerV1.0
alihaanc/SKYKILLER-Development-Board
Drone and Rocket Development PCB board
59 parts2 - 2 layers38 × 38 mm

MetalBird v2.kicad pro
Rajveer1496/MetalBird
A Drone made entirely from scratch. From PCB design and body to own Firmware.
67 parts2 - 2 layers45 × 45 mm

AVR FLIGHT CONTROLLER
syeedameen/miniflight
Budget Flight Controller for Drones with ATmega328P Microcontroller
65 parts2GPL-3.0 - 4 layers26.5 × 57.4 mm

MotorDriver
Kmshanley/MiniRobots
Firmware and PCB desgin for mini robots with UWB localization and lidar mapping
50 parts1
Questions
How big is the Cruz FlightComputerPCB PCB?
It measures 48 × 41.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Cruz FlightComputerPCB use?
14 parts, built around the BMP280 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cruz FlightComputerPCB KiCad files?
From the heallyc/FRL-NMP-flight-computer repository on GitHub, at the commit this page was made from: the board is Cruz_FlightComputerPCB.kicad_pcb and its schematic Cruz_FlightComputerPCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cruz FlightComputerPCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask heallyc before reusing the design.