
RC Aircraft PCB
sauravraj67/AURA-RC-PLANE-
I made a custom Tailless twin motor RC Plane with custom Flight Controller (based on STM32). The Flight Controller will have a IMU's and a barometer for precise data collection.

Budget Flight Controller for Drones with ATmega328P Microcontroller
AVR FLIGHT CONTROLLER is an open-source printed circuit board by syeedameen, from the syeedameen/miniflight repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 45 × 45 mm with 65 parts on 58 nets, routed with 766 tracks and 98 vias.
It is built around the ATMEGA328PB-AU, BMP280 and AMS1117-3.3, with the L7805, MPU-6050 and BSS138 among its other parts. Its parts include 19 capacitors, 15 resistors, 5 ICs, 4 diodes and 4 transistors. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Budget Flight Controller for Drones with ATmega328P Microcontroller
MPU6050 - Inertial Measurement Unit
BMP280 - Prassure & temprature sensor
ATmega328p Microcontroller
2-layer PCB design in KiCad EDA (manufactured from JLCPCB)
45 x 45 mm PCB size


| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R7, R8, R9, R10, R11, R12, R13 |
| 9 | 100nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C5, C6, C10, C12, C15, C17 |
| 4 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad_TopBottom | H1, H2, H3, H4 |
| 2 | 10uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C14 |
| 2 | 22pf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C11 |
| 2 | 330 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R15 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3, D4 |
| 1 | 0.1uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C18 |
| 1 | 10nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16 |
| 1 | 1N4148WT | Diode_SMD:D_SOD-523 | D1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 1uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | 2.2nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19 |
| 1 | 330nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 1 | 4.7uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | ATmega328PB-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U4 |
| 1 | CH_1 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | CH1 |
| 1 | CH_2 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | CH2 |
| 1 | CH_3 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | CH3 |
| 1 | CH_4 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | CH4 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | D_Zener | Diode_SMD:D_SOD-123 | D2 |
| 1 | ESC_1 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | ESC1 |
| 1 | ESC_2 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | ESC2 |
| 1 | ESC_3 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | ESC3 |
| 1 | ESC_4 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | ESC4 |
| 1 | ICSP | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | L7805 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U2 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U5 |
| 1 | Power Connector | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J3 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | UART | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | UART |
| 1 | ~ | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J1 |

sauravraj67/AURA-RC-PLANE-
I made a custom Tailless twin motor RC Plane with custom Flight Controller (based on STM32). The Flight Controller will have a IMU's and a barometer for precise data collection.


rmingon/Falcon-Edge
A 3D-printable flying-wing airframe with a custom ESP32 flight computer—open hardware you can solder, screw together, and fly.

IbrahimEssamIbrahim/Thrust-Vector-Controlled-Rocket-Design
This project proposes the development of a Thrust Vector-Controlled (TVC) rocket as an alternative to drones for high-altitude payload delivery.

adbik4/DL-FinalProject
The design and implementation of a measurement and data logging system based on ATmega328pb microcontroller. The system is intended for measuring temperature and pressure using dedicated digital sensors: DS18B20 and…



It measures 45 × 45 mm and has 2 copper layers, 1.6 mm thick.
65 parts, built around the ATMEGA328PB-AU, BMP280, AMS1117-3.3 and L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the syeedameen/miniflight repository on GitHub, at the commit this page was made from: the board is Hardware/AVR FLIGHT CONTROLLER.kicad_pcb and its schematic Hardware/AVR FLIGHT CONTROLLER.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).