

BMS Can Bus
Smart Battery Management System (BMS) with CAN Bus communication, using BQ76952 and KiCad.
- Size
- 127.4 × 101.5 mm
- Copper layers
- 2
- Thickness
- 1.81 mm
- Parts
- 59
- Nets
- 86
- Pads
- 240
- Tracks, vias
- 1,188, 194
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 16 Sep 2026
- Updated
- 19 Sep 2026
Overview
BMS Can Bus is an open-source printed circuit board by hasanberkdasar, from the hasanberkdasar/BMS-Can-Bus repository on GitHub, published under the MIT licence. It is a 2-layer board of 127.4 × 101.5 mm with 59 parts on 86 nets, routed with 1,188 tracks and 194 vias.
It is built around the SN65HVD230D and BQ76952PFBR. Its parts include 22 resistors, 17 capacitors, 8 transistors, 3 ICs and 3 connectors. It belongs with the power and interfaces and adapters boards and the STM32 boards of this library.
Main components
2SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversBQ76952PFBR
TQFP-48(7x7)-40℃~+85℃ 100mA 1uA 3~16 4.7V~80V I2C、SPI、HDQ Lithium Battery、LiFePO4 Battery Protection IC、Monitoring IC Support TQFP-48(7x7) Battery Management ROHSTexas InstrumentsBattery Management
README
README.mdSmart BMS (BQ76952 & STM32F103) — 4S Lithium Battery Management System
About The Project & Personal Context
This project is an open-source 4S Smart Battery Management System (BMS) designed around the Texas Instruments BQ76952 Analog Front-End (AFE) and an STM32F103C8T6 microcontroller.
As a 1st-year Electrical and Electronics Engineering student, this project represents my very first custom PCB design experience. It was built purely as a personal prototype, a learning step, and a hands-on exploration of power electronics and embedded hardware design. Because of my beginner level, the schematic and layout might appear complex, unoptimized, or messy in certain areas—it was developed as a continuous trial-and-error learning path.
⚠️ Important Engineering Note: Scaling Down from 100A to 5A
- Original Scope vs. Current Reality: The initial goal was to build a high-power 100A continuous BMS. However, as the design progressed, I realized that managing thermal dissipation and routing high-current copper paths properly on a standard 2-layer PCB exceeded my current technical expertise.
- Current Power Rating: To keep the design safe and realistic, the continuous current rating has been officially scaled down to 5A continuous (15A peak) for this version.
- Why Some Traces Look Unusually Large: You will notice that certain power paths on the board are disproportionately wide for a 5A system. These are remnants of the original 100A power path layout attempts.
- Tested Status: Please note that this design has NOT been physically fabricated or hardware-tested. It exists purely as a CAD/EDA design file.
- Future Outlook: The project is temporarily put on hold. Once I gain further engineering experience and technical proficiency, I plan to revisit this project to optimize thermal management and push the layout to support 100A peak and 50–60A continuous power on a computer simulation environment.
Architecture & Component Selection
1. Topology Selection (4S System)
A 4-series (4S) Lithium-ion / LiFePO4 configuration was selected as it matches standard low-voltage applications (such as 12V system upgrades, small EVs, or robotics power distribution) while offering a safe voltage range for learning.
2. Key Components & Selection Rationale
- Texas Instruments BQ76952 (AFE): Chosen for its highly integrated cell monitoring, hardware-level overvoltage/undervoltage protection, and flexible low-side/high-side FET drive capabilities.
- STM32F103C8T6 (MCU): Used as the primary host controller to read telemetry data via I2C/SMBus from the BQ76952, execute custom BMS logic, and manage external communications.
- SN65HVD230 (CAN Transceiver): Selected to convert the MCU's UART/CAN signals into a robust differential CAN-bus signal, making the BMS compatible with industrial and automotive telemetry networks.
- NTC Thermistors: External thermistor headers are added for real-time thermal monitoring of the battery pack and power MOSFETs.
Circuit Interconnections & Features
- Power Path: Utilizes dual-layer 2mm copper traces with a high-side back-to-back MOSFET pair (paralleled discharge/charge FETs) for battery isolation, and a low-side shunt resistor for current sensing.
- Noise Immunity & Layout: Decoupling capacitors are placed in immediate proximity to the power pins of both the AFE and MCU. The 8MHz crystal load capacitors are locked close to the oscillator pins.
- EMC Shielding: Top and bottom layers are encased with a solid Ground (GND) polygon pour for noise suppression.
- Communication Interface: Dedicated CAN-Bus interface pins enable continuous telemetry streaming (cell voltages, pack current, temperatures, and fault flags) to external dashboards or vehicle control units (VCU).
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0603_1608Metric | C11, C12, C13, C14, C17, C18, C19 |
| 6 | 10k ohm | Resistor_SMD:R_0805_2012Metric | R15, R16, R17, R18, R21, R22 |
| 4 | 100 OHM | Resistor_SMD:R_0603_1608Metric | R5, R7, R9, R11 |
| 4 | 21 OHM | Resistor_SMD:R_2512_6332Metric | R6, R8, R10, R12 |
| 4 | C | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6 |
| 4 | Q_PMOS_GSD | Package_TO_SOT_THT:TO-220-3_Vertical | Q3, Q4, Q5, Q6 |
| 3 | 100 ohm | Resistor_SMD:R_0805_2012Metric | R1, R2, R14 |
| 2 | 10 ohm | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 10k NTC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | TH1, TH2 |
| 2 | 1uF 25v | Capacitor_SMD:C_0603_1608Metric | C9, C10 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 4.7k ohm | Resistor_SMD:R_0805_2012Metric | R19, R20 |
| 1 | 120 ohm | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | 1miliohm | Resistor_THT:R_Axial_DIN0414_L11.9mm_D4.5mm_P25.40mm_Horizontal | RShuntResistor1 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | BQ76952PFB | Package_QFP:TQFP-48_7x7mm_P0.5mm | U1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | Crystal_Small | Crystal:Crystal_HC49-4H_Vertical | 8MHZ1 |
| 1 | PACK+ | MountingHole:MountingHole_5.3mm_M5_Pad | J_PACK+1 |
| 1 | PACK- | MountingHole:MountingHole_5.3mm_M5_Pad | J_PACK-1 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | bat+ | MountingHole:MountingHole_3.2mm_M3_Pad | J3 |
| 1 | chg1 | Package_TO_SOT_SMD:TO-263-2 | Q7 |
| 1 | chg2 | Package_TO_SOT_SMD:TO-263-2 | Q8 |
| 1 | dfsg1 | Package_TO_SOT_SMD:TO-263-2 | Q1 |
| 1 | dsg2 | Package_TO_SOT_SMD:TO-263-2 | Q2 |
Similar boards
- 2 layers100 × 100 mm

- 4 layers87.5 × 129.5 mm

- 4 layers83.3 × 88.1 mm

Bottom PCB
StanZalewski/Autonomous-remote-monitoring-system-based-on-the-LoRaWAN-protocol
Solar-powered LoRaWAN weather station — 3 custom PCBs, bare-metal STM32, 4.3 km verified link
124 parts - 4 layers106 × 98 mm

Motion control
menloresearch/asimov-1
v1 of Asimov, an open-source humanoid robot
76 parts1.4kCERN-OHL-S-2.0 - 2 layers40.5 × 58 mm

Initial v
tenderlove/initial-v
It's a BMW shifter converted to a Bluetooth Keyboard that you use with Vim
30 parts1kApache-2.0 - 4 layers42 × 42 mm

- 4 layers85 × 85 mm

- 2 layers120 × 80 mm

Rx72t 100 pga usb
hirakuni45/RX
Renesas RX Microcontroller, C++ framework, Library, Sample
113 parts86BSD-3-Clause
Questions
How big is the BMS Can Bus PCB?
It measures 127.4 × 101.5 mm and has 2 copper layers, 1.81 mm thick.
What parts does the BMS Can Bus use?
59 parts, built around the SN65HVD230D and BQ76952PFBR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BMS Can Bus KiCad files?
From the hasanberkdasar/BMS-Can-Bus repository on GitHub, at the commit this page was made from: the board is BMS-Can-Bus.kicad_pcb and its schematic BMS-Can-Bus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BMS Can Bus design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).