

LampeSolaire
Projet de lampe solaire avec pcb et software
- Size
- 85 × 83 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 41
- Pads
- 164
- Tracks, vias
- 441, 68
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 30 Jan 2019
- Updated
- 9 Oct 2019
Overview
LampeSolaire is an open-source printed circuit board by esseivan, from the esseivan/Lampe-Solaire repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 85 × 83 mm with 58 parts on 41 nets, routed with 441 tracks and 68 vias.
It is built around the PIC16LF1827-I/P, LD39200PUR and NCP114ASN330T1G, with the SI2333 and FDN337N among its other parts. Its parts include 18 resistors, 10 capacitors, 8 connectors, 6 ICs and 4 crystals. It belongs with the PIC boards of this library.
Main components
5PIC16LF1827-I/P
PDIP-18-40℃~+85℃ 1.8V~3.6V 10bit 16 256Byte 32MHz 384Byte 7KB 8 Bit Built-in FLASH PIC PDIP-18 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LD39200PUR
DFN-6(3x3)-40℃~+125℃@(Tj) 1 24uVrms 250mV@(2A) 2A 300uA 500mV~5.75V 6V 70dB@(1kHz) Adjustable PG Pin、Over Current Protection、Reverse connection protection、Thermal Shutdown Positive DFN-6(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsNCP114ASN330T1G
TSOP-5-1.5mm-40℃~+85℃@(Tj) 1 225mV@(300mA) 3.3V 300mA 5.5V 50uA 70uVrms 75dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOP-5-1.5mm Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSI2333
SOT-23-55℃~+150℃ 1 P-Channel 1.25W 12V 1V 220pF 5.1A 59mΩ@1.8V 8V 920pF SOT-23 MOSFETs ROHSBORNMOSFETsFDN337N
SOT-23-55℃~+150℃ 1 N-channel 120pF 2.2A 300pF 30V 400mV 500mW 65mΩ@4.5V 80pF SOT-23 MOSFETs ROHSTECH PUBLICMOSFETs
README
README.mdLampeSolaire
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100nF | 0EsseivaN_Lib:C_0805_HandSoldering | C3, C4, C5, C6, C8 |
| 4 | 4.7uF | 0EsseivaN_Lib:C_0805_HandSoldering | C1, C7, C9, C10 |
| 3 | GREEN | 0EsseivaN_Lib:D_0603_HandSoldering | P5, P6, P8 |
| 3 | TEST_2P | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | W3, W4, W5 |
| 2 | 10R | 0EsseivaN_Lib:Potentiometer_Trimmer_Bourns_3006P | R11, R13 |
| 2 | 10k | 0EsseivaN_Lib:R_0805_HandSoldering | R17, R18 |
| 2 | 270R | 0EsseivaN_Lib:R_0805_HandSoldering | R8, R16 |
| 2 | 330R | 0EsseivaN_Lib:R_0805_HandSoldering | R6, R9 |
| 2 | 3V | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | P2, P3 |
| 2 | 4k7 | 0EsseivaN_Lib:R_0805_HandSoldering | R3, R12 |
| 2 | NP | 0EsseivaN_Lib:R_0805_HandSoldering | R14, R15 |
| 2 | RED | 0EsseivaN_Lib:D_0603_HandSoldering | P4, P7 |
| 2 | SI2333 | 0EsseivaN_Lib:SOT-23_Handsoldering | T1, T2 |
| 2 | ~ | 0EsseivaN_Lib:PERC-4.5mm | PERC-4.5mm, PERC-4.5mm |
| 1 | 100k | 0EsseivaN_Lib:R_0805_HandSoldering | R4 |
| 1 | 10M | 0EsseivaN_Lib:R_0805_HandSoldering | R7 |
| 1 | 10uF | 0EsseivaN_Lib:C_0805_HandSoldering | C2 |
| 1 | 1V8 | 0EsseivaN_Lib:D_0603_HandSoldering | P1 |
| 1 | 1k5 | 0EsseivaN_Lib:R_0805_HandSoldering | R5 |
| 1 | 27k | 0EsseivaN_Lib:R_0805_HandSoldering | R10 |
| 1 | 3k3 | 0EsseivaN_Lib:R_0805_HandSoldering | R1 |
| 1 | 3k9 | 0EsseivaN_Lib:R_0805_HandSoldering | R2 |
| 1 | 630mA | Fuse_Holders_and_Fuses:Fuse_SMD1206_HandSoldering | F1 |
| 1 | BATTERY_JUMPER | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | X1 |
| 1 | BUZZER | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | X4 |
| 1 | FDN337 | 0EsseivaN_Lib:SOT-23_Handsoldering | T3 |
| 1 | ICSP | 0EsseivaN_Lib:Pin_Header_Straight_1x05_Pitch2.54mm | X2 |
| 1 | LD39200 | 0EsseivaN_Lib:DFN-6-1EP_3x3mm_Pitch0.95mm | U7 |
| 1 | Li battery | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | V2 |
| 1 | Li battery | 0EsseivaN_Lib:18650 Battery holder | V1 |
| 1 | MCP121 | 0EsseivaN_Lib:SOT-23_Handsoldering | U2 |
| 1 | MCP73832 | 0EsseivaN_Lib:SOT-23-5_HandSoldering | U1 |
| 1 | NCP114ASN330T1G | 0EsseivaN_Lib:TSOP-5 | U3 |
| 1 | PIC16LF1827 | Housings_SSOP:SSOP-20_5.3x7.2mm_Pitch0.65mm | U5 |
| 1 | RF_RECEIVER, NP | 0EsseivaN_Lib:RF_RECEIVER | U8 |
| 1 | Solar_Cells | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | SC1 |
| 1 | WATER_SENSOR | 0EsseivaN_Lib:Pin_Header_Straight_1x02_Pitch2.54mm | X6 |
More from esseivan/Lampe-Solaire
1- 2 layers12.7 × 96.5 mm

Similar boards
- 2 layers27 × 48 mm

ENBLE
idt12312/ENBLE
ENBLE is the environmental sensor which measures temperature, humidity, and air pressure and sends them over BLE.
18 parts3 - 2 layers43 × 43 mm

- 2 layers50.8 × 88.9 mm

Mss debug
IowaScaledEngineering/mss-debug
Diagnostic and debug module for the Modular Signal System
69 parts - 2 layers128.7 × 60.3 mm

MOBILE
sumit123hub/Mobile-PCB-Files-
I always dreamed of building my own mobile system. This repo documents my journey designing a custom ESP32 PCB featuring a GSM module, display interface, and complete Battery Management System (BMS).
92 parts - 2 layers35 × 40 mm

- 2 layers114 × 49.3 mm

Solderbit gamepad
devices-lab/solderbit-gamepad
Learn-to-solder kit for the BBC micro:bit
58 parts4GPL-3.0 - 2 layers309.5 × 188.8 mm

- 4 layers80 × 60 mm

Questions
How big is the LampeSolaire PCB?
It measures 85 × 83 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LampeSolaire use?
58 parts, built around the PIC16LF1827-I/P, LD39200PUR, NCP114ASN330T1G and SI2333. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LampeSolaire KiCad files?
From the esseivan/Lampe-Solaire repository on GitHub, at the commit this page was made from: the board is Hardware/LampeSolaire/LampeSolaire.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the LampeSolaire design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).