

Step up
Misc smart house hardware
- Size
- 49.5 × 57.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 22
- Pads
- 105
- Tracks, vias
- 232, 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Oct 2017
- Updated
- 11 Oct 2023
Overview
Step up is an open-source printed circuit board by dzavalishin, from the dzavalishin/hardware repository on GitHub. It is a 2-layer board of 49.5 × 57.2 mm with 40 parts on 22 nets, routed with 232 tracks and 4 vias.
It is built around the 74HC04D, L78L33ACU and LM2903, with the IRFR024N and SB360 among its other parts. Its parts include 17 capacitors, 11 resistors, 3 ICs, 1 diode and 1 transistor.
Main components
574HC04D
SOP-14-40℃~+125℃ 1 1.5V~4.2V 1.9V、3.7V、5.2V 100mV、400mV、400mV 14ns@6V,50pF 2V~6V 2uA 5.2mA 5.2mA 500mV~1.8V 6 74HC SOIC-14 Inverters ROHSNexperiaInvertersL78L33ACU
SOT-89-30℃~+125℃@(Tj) 1 1.7V 100mA 3.3V 30V 40uV 49dB@(120Hz) 6mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM2903
SOP-8-18V~-1V、1V~18V 0℃~+70℃ 10mV 1mV 2 25nA 2V~36V 36V 400uA 5nA DTL、TTL、CMOS、ECL、MOS Open Collector SOP-8 Comparators ROHSHXY MOSFETComparatorsIRFR024N
TO-252-55℃~+175℃ 1 N-channel 1.9nF 2.5V 25A 30nC@30V 33mΩ@10V 50W 60V 95pF TO-252 MOSFETs ROHSTECH PUBLICMOSFETsSB360
DO-27-55℃~+150℃ 1 Independent 100uA@60V 3A 60V 700mV@3A 80A DO-27 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky Diodes
README
README.mdhardware
Misc smart house hardware, kicad designs.
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0,1 | Capacitors_SMD:C_1206_HandSoldering | C1, C4, C8, C9, C14, C16, C17 |
| 5 | 3,3k | Resistors_SMD:R_1206_HandSoldering | R2, R3, R5, R9, R11 |
| 3 | Mounting_Holes:MountingHole_3.2mm_M3 | , , | |
| 3 | 1k | Resistors_SMD:R_1206_HandSoldering | R1, R6, R8 |
| 2 | 0,33 | Capacitors_SMD:C_1206_HandSoldering | C12, C13 |
| 2 | 1,0 | Capacitors_SMD:C_1206_HandSoldering | C2, C5 |
| 2 | 10,0 | Capacitors_SMD:CP_Elec_4x5.3 | C11, C15 |
| 2 | 47,0 | SMD_Packages:SMD-2112_Pol | C3, C6 |
| 2 | 50k | Potentiometers:Potentiometer_Trimmer_Bourns_3296W | RV1, RV2 |
| 1 | 0,1 | Resistors_SMD:R_2512_HandSoldering | R4 |
| 1 | 1,5k | Resistors_SMD:R_1206_HandSoldering | R10 |
| 1 | 100uH | Choke_Toroid_ThroughHole:Choke_Toroid_8x16mm_Vertical | L1 |
| 1 | 1n | Capacitors_SMD:C_1206_HandSoldering | C7 |
| 1 | 200k | Resistors_SMD:R_1206_HandSoldering | R7 |
| 1 | 4700 | Capacitors_SMD:C_1206_HandSoldering | C10 |
| 1 | 74HC04 | Housings_DIP:DIP-14_W7.62mm | U1 |
| 1 | IRFR024 | TO_SOT_Packages_SMD:TO-252-3_TabPin2 | Q1 |
| 1 | L78L33 | TO_SOT_Packages_THT:TO-92_Inline_Narrow_Oval | U3 |
| 1 | LM2903 | Housings_DIP:DIP-8_W7.62mm | U2 |
| 1 | Power | Connectors_Terminal_Blocks:TerminalBlock_bornier-3_P5.08mm | J1 |
| 1 | SB360 | Diodes_SMD:D_3220 | D1 |
More from dzavalishin/hardware
12- 2 layers

- 2 layers156.2 × 86.4 mm

- 2 layers

- 2 layers124.5 × 81.3 mm

- 2 layers254 × 55.9 mm

- 2 layers71 × 140 mm

- 2 layers106.7 × 58.4 mm

- 2 layers108 × 77.5 mm

- 2 layers68.9 × 118.5 mm

- 2 layers155 × 58 mm

- 2 layers90.2 × 72.4 mm

- 2 layers20.3 × 200.7 mm

Similar boards
- 4 layers71.9 × 91 mm

Klipper
tobetter/3DPrinterShield
"3D Printer Shield" is a board to run 3D printer using ODROID single board computer, technically this board is designed to control the motor driver modules with TMC2209 (UART) or TMC2130 (SPI) through the on-board GPIO…
111 parts4GPL-3.0 - 2 layers100 × 99.8 mm

Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
152 parts19 - 2 layers180 × 58 mm

Handheld sstc
automagicle/handheld-sstc
A handheld SSTC project on PCB, designed for a large magic wand form factor, entirely powered from 8s 18650. Uses direct secondary feedback with gate driver and MOSFETs, and 555 interrupter
66 parts1 - 2 layers99.7 × 48.8 mm

AC DC Wandler
MoElashmawi/Flyback-AC-DC-Converter
Flyback AC-DC Converter (230V AC to 12V DC) — Full SMPS design using VIPer22A PWM Controller. Schematic, PCB layout & 3D render in KiCad.
34 parts1MIT - 2 layers110.7 × 74.7 mm

- 2 layers100 × 56.5 mm

Pi dash input hat
outlandfabworks/overdash
Open-source Raspberry Pi vehicle dashboard. Reads CAN (J1939), OBD-II, Megasquirt/Speeduino, GPS, and GPIO — streams to a canvas-based kiosk frontend with a visual no-code layout editor.
68 partsMIT - 4 layers100 × 100 mm

Intel 8088 Computer
oberrow/i8088-computer
Code for an i8088-based non-PC compatible breadboard computer
69 parts1MIT - 4 layers99.5 × 91 mm

Questions
How big is the Step up PCB?
It measures 49.5 × 57.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Step up use?
40 parts, built around the 74HC04D, L78L33ACU, LM2903 and IRFR024N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Step up KiCad files?
From the dzavalishin/hardware repository on GitHub, at the commit this page was made from: the board is _Power/step_up/step_up.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Step up design in my own project?
Its repository states no licence, so its author keeps all rights: ask dzavalishin before reusing the design.