

Sensor board
A robotic and software orientated ocean development.
- Size
- 22.2 × 28 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 21
- Nets
- 45
- Pads
- 96
- Tracks, vias
- 133, 12
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 29 May 2022
- Updated
- 31 Oct 2023
Overview
Sensor board is an open-source printed circuit board by daniel360kim, from the daniel360kim/OceanAI repository on GitHub, published under the MIT licence. It is a 2-layer board of 22.2 × 28 mm with 21 parts on 45 nets, routed with 133 tracks and 12 vias.
It is built around the ATSAMD21G18A-AU. Its parts include 9 capacitors, 4 resistors, 4 connectors, 1 IC and 1 diode. It belongs with the sensors and measurement boards and the SAM D and SAM boards of this library.
Main components
1README
PCBs/sensor_board/README.mdTransmitter Board

This directory contains the PCB designs for the sensor board.
The front of the submarine contains several sensors underwater: a pressure transducer and a thermistor. The pressure transducer is used to measure the pressure of the water. The thermistor is used to measure the temperature of the water. The sensor board reads these sensors and sends the data to the main board through I2C.
Power:
- 3.3V (no voltage regulator onboard - must be clean 3.3V)
Sensors:
- Analog input for external pressure transducer
- 10K Thermistor for water temperature readings
Communication:
- Communicated to the submarine main_board through I2C.
- The board features SWD interface for debugging and is programmed through SWD.
What's done?
- Schematic is finished.
- PCB layout is finished
- 3D models and fabrication outputs are generated
What's to do?
- Ordering and fabrication
Parts
21| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6, C7, C9 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 32768Hz | Crystal:XTAL_ABS07-32.768KHZ-T | Y1 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | ATSAMD21G18A-A | Package_QFP:TQFP-48_7x7mm_P0.5mm | U1 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | Thermistor (10K) | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Transducer | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | ~{RESET} | Button_Switch_SMD:PTS810SJG250SMTRLFS | SW1 |
More from daniel360kim/OceanAI
2- 4 layers62.8 × 97.5 mm

- 4 layers34 × 65 mm

Similar boards
- 4 layers70.8 × 108 mm

- 2 layers36 × 20 mm

- 4 layers35.1 × 76.3 mm

Tiny4FSK
New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker
90 parts96CERN-OHL-W-2.0 - 4 layers36.6 × 60.3 mm

StratoSoar MK3.0
crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone
85 parts43 - 4 layers42 × 83.9 mm

StratoSoar MK2.2
crnicholson/StratoSoar-MK2
StratoSoar is an engineering project that aims to be able to fly a glider (dropped from a high-altitude balloon), down to any selected coordinates.
116 parts24 - 2 layers69.8 × 40.4 mm

T Piece Kicad
calebmarting/os2026-badge
Schematics and firmware for the Open Sauce 2026 Badge and SAOs
82 parts23MIT - 2 layers51.8 × 51.8 mm

Pawpet
NanoCodeBug/pawpet
A virtual pet using the atsamd21g and sharp memory lcd, runs off of 2xAAA for a couple of months. See PawPet on Hacakday.io for full gallery.
41 parts20 - 4 layers117 × 107 mm

Mainboard dual battery
shurik179/yozh
Small robot based on Pololu's Zumo chassis but programmable in CircuitPython
121 parts8MIT
Questions
How big is the Sensor board PCB?
It measures 22.2 × 28 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Sensor board use?
21 parts, built around the ATSAMD21G18A-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sensor board KiCad files?
From the daniel360kim/OceanAI repository on GitHub, at the commit this page was made from: the board is PCBs/sensor_board/sensor_board.kicad_pcb and its schematic PCBs/main_board/IMU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sensor board design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).