

HAT CM4
Connectbox Circuit Design
- Size
- 105 × 78 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 139
- Nets
- 152
- Pads
- 809
- Tracks, vias
- 1,737, 275
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20210228)
- Created
- 31 Jul 2018
- Updated
- 9 Mar 2025
Overview
HAT CM4 is an open-source printed circuit board by ConnectBox, from the ConnectBox/Circuit-Design repository on GitHub. It is a 4-layer board of 105 × 78 mm with 139 parts on 152 nets, routed with 1,737 tracks and 275 vias.
It is built around the ATTINY88-AU, MAX1709ESE+T and RT9742ANGJ5F, with the AT24CS01-SSHM-B, AXP209 and FSUSB42MUX among its other parts. Its parts include 39 capacitors, 36 resistors, 14 ICs, 9 diodes and 8 connectors. It belongs with the computers and single-board computers boards and the AVR (ATmega, ATtiny) and Raspberry Pi (Linux) boards of this library.
Main components
9ATTINY88-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 12MHz 28 512Byte 64Byte 8 Bit 8KB AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MAX1709ESE+T
SOP-16-40℃~+85℃@(TA) 1 1MHz 2.5V~5.5V 7.5A 700mV~5V Adjustable Boost Boost Built-in No SOP-16 DC-DC Converters ROHSMaxim Integrated (Analog Devices)DC-DC ConvertersRT9742ANGJ5F
TSOT-23-5-40℃~+85℃ 1 2.7V~6V 3A 55mΩ Active High High Side Switch 输出放电功能、软启动、欠压锁定、反向电压保护、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、反向电流阻断 TSOT-23-5 Power Distribution Switches ROHSRichtek TechPower Distribution SwitchesAT24CS01-SSHM-B
SOIC-8-40℃~+85℃ 1.7V~5.5V 1Kbit 1MHz 5ms I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMAXP209
QFN-48-EP(6x6)Overcurrent Protection、Operating status indication、Adjustable current limiting、Power-on timing control QFN-48-EP(6x6) Power Management - Specialized ROHSX-Powers TechBattery ManagementFSUSB42MUX
MSOP-10-40℃~+85℃ 12ns 13ns 2 250ps 2:1 3.7pF 3.9Ω 3V~4.4V 720MHz MSOP-10 Analog Switches, Multiplexers ROHSonsemiAnalog Switches, MultiplexersRT9742SNGV
SOT-23-3-40℃~+85℃ 1 2.7V~6V 500mA 70mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Undervoltage Protection(UVP)、Overcurrent Protection(OCP)、Over Temperature Protection SOT-23-3 Power Distribution Switches ROHSRichtek TechPower Distribution SwitchesUSB2514B-I/M2
SQFN-36-EP(6x6)-40℃~+85℃ 3.3V 4 Hub I2C USB 2.0 SQFN-36-EP(6x6) USB HUB Controllers ROHSMicrochip TechnologyUSB HUB ControllersMMBD914
SOT-231.25V@150mA 100V 1uA@75V 300mA 350mW 4ns 500mA Independent SOT-23 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes
README
README.mdCircuit-Design
Connectbox Circuit Design
This repo contains the schematic and KiCAD design files for the NEO-USB-HAT. This is a daugherboard to add an extra USB port and power input to a NanoPi NEO.
Parts
139| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 10uF | Capacitor_SMD:C_0603_1608Metric | C2, C3, C4, C5, C14, C15, C19, C20, C27, C29, C31, C32, C33 |
| 9 | 0.1uf | Capacitor_SMD:C_0603_1608Metric | C11, C12, C21, C22, C23, C24, C25, C26, C38 |
| 7 | 10K | Resistor_SMD:R_0603_1608Metric | R2, R9, R10, R12, R29, R34, R35 |
| 6 | 2.2K | Resistor_SMD:R_0603_1608Metric | R7, R8, R16, R22, R23, R33 |
| 6 | 8205A | Package_SO:TSSOP-8_4.4x3mm_P0.65mm | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | 150uf | Capacitor_SMD:CP_Elec_5x3 | C35, C36, C39, C40 |
| 4 | 1K | Resistor_SMD:R_0603_1608Metric | R11, R12, R15, R32 |
| 4 | 36.0K | Resistor_SMD:R_0603_1608Metric | R24, R25, R26, R28 |
| 4 | Battery_Cell | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | BT1, BT2, BT3, BT4 |
| 4 | MMBD914 | Diode_SMD:D_SOT-23_ANK | D1, D3, D4, D6 |
| 3 | 12K | Resistor_SMD:R_0603_1608Metric | R13, R21, R27 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C9, C10, C13 |
| 3 | 22uF | Capacitor_SMD:C_0603_1608Metric | C1, C30, C34 |
| 3 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C6, C7, C8 |
| 3 | TPD4EUSB30 | CustomComponents:USON-10_2.5x1.0mm_P0.5mm | U4, U5, U9 |
| 2 | 27pF | Capacitor_SMD:C_0603_1608Metric | C17, C18 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric | R19, R20 |
| 2 | RT9742ANGJ5F | Package_TO_SOT_SMD:SOT-23-5 | U6, U11 |
| 2 | SPST-PUSH | CustomComponents:SW-TL3305 | PB1, PB2 |
| 2 | USB_A | CustomComponents:USB_A | J4, J5 |
| 2 | nf | Resistor_SMD:R_0603_1608Metric | R17, R18 |
| 1 | |||
| 1 | 0.03 ohm | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 0.22uf | Capacitor_SMD:C_0603_1608Metric | C37 |
| 1 | 1.0 uH | Inductor_SMD:L_Taiyo-Yuden_MD-5050 | L2 |
| 1 | 1.5 uH | Inductor_SMD:L_Taiyo-Yuden_NR-50xx | L3 |
| 1 | 1.8K | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 100uF | Capacitor_SMD:CP_Elec_6.3x4.5 | C28 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 2.0 | Resistor_SMD:R_0603_1608Metric | R31 |
| 1 | 200K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 220K | Resistor_SMD:R_0603_1608Metric | R30 |
| 1 | 24MHz | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | 4.7 uH | CustomComponents:INDUCTOR_SMD_6x6-1 | L1 |
| 1 | 51K | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 5V | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP8 |
| 1 | 690-019-298-412 | CM4IO:EDAC 690-019-298-412 | J1 |
| 1 | AC_IN | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP2 |
| 1 | AT24CS01-SSHM | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ATtiny88-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U7 |
| 1 | AXP209 | CustomComponents:UQFN-48-1EP_6x6mm_Pitch0.4mm_75 | U1 |
| 1 | Amber | LED_SMD:LED_0603_1608Metric | LED2 |
| 1 | Bat+ | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP3 |
| 1 | ComputeModule4 | CM4IO:Raspberry-Pi-4-Compute-Module | Module1 |
| 1 | Conn_01x02_Female | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | P1 |
| 1 | DML10M8LDS-13 | CustomComponents:DML10M8LDS-13 | U13 |
| 1 | FSUSB42MUX | Package_SO:MSOP-10_3x3mm_P0.5mm | U8 |
| 1 | Green | LED_SMD:LED_0603_1608Metric | LED3 |
| 1 | HC-R8812AF1 | CustomComponents:HC-R8812AU2-th-1 | U12 |
| 1 | IPS | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP4 |
| 1 | IPS_Sw | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP7 |
| 1 | LED Green | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | MAX1709ESE | Package_SO:SOP-16_3.9x9.9mm_P1.27mm | U14 |
| 1 | MagJack-L829-1J1T-JM | CustomComponents:MagJack L829-1J1T-JM | J6 |
| 1 | Micro_SD_Card_Det | CM4IO:SDCARD_MOLEX_503398-1892 | J2 |
| 1 | Molex PicoBlade 53047-0210 | CustomComponents:Molex PicoBlade 53047-0210 - (swapped pins) | BAT1 |
| 1 | NRVTS260ESFT1G | CustomComponents:SOD-123FL | D5 |
| 1 | Pwr_Gnd | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | TP1 |
| 1 | RT9742SNGV | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | Red | LED_SMD:LED_0603_1608Metric | LED1 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | TP5 |
| 1 | USB2514B-I/M2 | Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm | U10 |
| 1 | USB_OTG | CM4IO:USB_Micro-B_EDAC_UCON00686 | J3 |
The 133 most common of 139 parts.
More from ConnectBox/Circuit-Design
12- 2 layers299.3 × 93.1 mm

- 6 layers105.6 × 86.1 mm

- 6 layers105.6 × 86.1 mm

- 2 layers56.6 × 71.6 mm

- 2 layers57.4 × 71.6 mm

- 2 layers66 × 81.6 mm

- 4 layers53.7 × 87 mm

- 4 layers41.6 × 79.2 mm

- 2 layers52.3 × 80.4 mm

- 2 layers57.6 × 88.2 mm

- 2 layers52 × 23.2 mm

- 2 layers52 × 23.4 mm

Similar boards
- 4 layers160 × 90 mm

- 4 layers100 × 100 mm

CM4IOv5
NBence0/JedlikBots
Welcome to the official GitHub page of JedlikBots! 🎓🤖 We are the dedicated team of software development and robotics students from the Jedlik Ányos Technical School in Győr, Hungary.
226 parts - 2 layers76 × 28 mm

- 4 layers80 × 70 mm

CM4IOv5
vega-d/CM4-nano-carrierboard
A simplified carrier board for RPI CM4 module featuring reduced footprint.
66 parts11GPL-3.0 - 4 layers110 × 100 mm

- 4 layers40 × 55 mm

CM4 Carrier
xwlred/OpenHD-CM4-Carrier-Board
[Shelved] RPI CM4 carrier for use in OpenHD
73 parts14LGPL-2.1 - 2 layers213.7 × 137.6 mm

- 4 layers100 × 100 mm

UMMTJ Mainboard
vamatis/UMMTJ
A universal Test jig setup for small production and prototype shops
147 parts
Questions
How big is the HAT CM4 PCB?
It measures 105 × 78 mm and has 4 copper layers, 4.69 mm thick.
What parts does the HAT CM4 use?
139 parts, built around the ATTINY88-AU, MAX1709ESE+T, RT9742ANGJ5F and AT24CS01-SSHM-B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HAT CM4 KiCad files?
From the ConnectBox/Circuit-Design repository on GitHub, at the commit this page was made from: the board is Hat_7.0.6/Flex_1.0/HAT_CM4.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the HAT CM4 design in my own project?
Its repository states no licence, so its author keeps all rights: ask ConnectBox before reusing the design.