Skip to the content

Interfaces and adapters

7,328 boards
  • 2 layers24.5 × 32.3 mmRGB to hdmi adapter coco3, the printed circuit board in 3D

    RGB to hdmi adapter coco3

    qbancoffee/coco_rgb_to_hdmi_adapter

    RGB to HDMI adapter boards for the CoCo 1, the CoCo 2 and the CoCo 3.

    5 parts9AGPL-3.0
  • 2 layers13 × 22 mmFlash adapter, the printed circuit board in 3D

    Flash adapter

    Rogger/schneggi-sensor

    A low-power ZigBee sensor integrated with HomeAssistant for monitoring temperature, humidity, and CO2.

    3 parts9GPL-3.0
  • 4 layers65 × 37.5 mmCLAS Combo Breakout BKUP, the printed circuit board in 3D

    CLAS Combo Breakout BKUP

    takuhoTech/CelestNavi-Combo

    Ready-to-use GNSS+CLAS receiver with integrated loop antenna

    71 parts9MIT
  • 2 layers14.2 × 30 mmUsd adapter, the printed circuit board in 3D

    Usd adapter

    3mdeb/sd-mux

    Control application for SD Wire imported from: https://git.tizen.org/cgit/tools/testlab/sd-mux/

    2 parts8Apache-2.0
  • 2 layers125.7 × 97.8 mmQL CST FLoppyController V3, the printed circuit board in 3D

    QL CST FLoppyController V3

    alvaroalea/QL_CST_FLoppyController

    A clone of the CST's Floppy Disk Interface for Sinclair QL (PCB version 3 & 4)

    25 parts8
  • 2 layers38.1 × 29.2 mmSht31 breakout, the printed circuit board in 3D

    Sht31 breakout

    alvarop/ostur

    This is a work in progress for a cheese cave controller system. The goal is to be able to control a mini fridge to get the right conditions for cheesemaking.

    5 parts8MIT
  • 2 layers139 × 84.2 mmMacintosh Portable Battery Adapter v1.0, the printed circuit board in 3D

    Macintosh Portable Battery Adapter v1.0

    alxlab-zone66x/Macintosh_Portable_Battery_Adapter

    This project aims to make a PCB and case to easily use a standard 6V lead-acid battery with spade connector as the Macintosh Portable battery.

    4 parts8
  • 2 layers139 × 84.2 mmMacintosh Portable Battery Adapter v1.1, the printed circuit board in 3D

    Macintosh Portable Battery Adapter v1.1

    alxlab-zone66x/Macintosh_Portable_Battery_Adapter

    This project aims to make a PCB and case to easily use a standard 6V lead-acid battery with spade connector as the Macintosh Portable battery.

    8 parts8
  • 4 layers43.5 × 31.5 mmBreakout, the printed circuit board in 3D

    Breakout

    azonenberg/sky130-validation

    Silicon validation projects for SKY130 stuff

    16 parts8BSD-3-Clause
  • 2 layers60 × 51 mmHalf bridge mod, the printed circuit board in 3D

    Half bridge mod

    cclienti/tig-welder

    A DIY TIG welder that can be plugged to a traditionnal stick welder or to a high current source

    20 parts8GPL-3.0
  • 2 layers45.7 × 38 mmSmartLED Shield Breakout, the printed circuit board in 3D

    SmartLED Shield Breakout

    coelacant1/Protogen-Electronics

    SmartMatrix SmartLED Shield breakout for Protogen hardware

    24 parts8GPL-3.0
  • 2 layers55.1 × 112.5 mmCw optics cwside, the printed circuit board in 3D

    Cw optics cwside

    colinoflynn/phase-modulation-sca

    Resources to demonstrate phase modulation leakage including over JTAG

    44 parts8
  • 2 layers55.1 × 98.8 mmCw optics targetside, the printed circuit board in 3D

    Cw optics targetside

    colinoflynn/phase-modulation-sca

    Resources to demonstrate phase modulation leakage including over JTAG

    40 parts8
  • 2 layers82.8 × 46.5 mmJtag mixer, the printed circuit board in 3D

    Jtag mixer

    colinoflynn/phase-modulation-sca

    Resources to demonstrate phase modulation leakage including over JTAG

    27 parts8
  • 2 layers20 × 29.9 mmJst breakout, the printed circuit board in 3D

    Jst breakout

    cyberboy666/lateral_led_controller

    hardware network controller for addressable led installations

    3 parts8GPL-3.0
  • 2 layers20 × 29.9 mmRj45 breakout, the printed circuit board in 3D

    Rj45 breakout

    cyberboy666/lateral_led_controller

    hardware network controller for addressable led installations

    2 parts8GPL-3.0
  • 2 layersH bridge, the printed circuit board in 3D

    H bridge

    dfdc1123/knead-net-gui

    This KiCad project was converted from the GPL-3.0 TM1637 display module published by zhbaa on OSHWHub and normalized to the project name tm1637-display-module.

    18 parts8GPL-3.0
  • 2 layers16 × 44 mmSparkFun HSTX PTH Breakout, the printed circuit board in 3D

    SparkFun HSTX PTH Breakout

    embeddedos-org/eCAD-Hardware-Products

    Hardware designs + EE docs + Board datasheets of Multiple products

    43 parts8MIT
  • 4 layers25.4 × 25.4 mmSparkFun HSTX to DVI Breakout, the printed circuit board in 3D

    SparkFun HSTX to DVI Breakout

    embeddedos-org/eCAD-Hardware-Products

    Hardware designs + EE docs + Board datasheets of Multiple products

    30 parts8MIT
  • 2 layers50.8 × 58.1 mmCOMiX FTDI Adapter, the printed circuit board in 3D

    COMiX FTDI Adapter

    etxmato/COMiX-HighSpeedDirectConnect

    COMiX High Speed Direct Connect

    6 parts8
  • 2 layersCart programmer, the printed circuit board in 3D

    Cart programmer

    JiggleSoft/atari2600_cart_prog

    Atari 2600 Budget ROM Cartridge, Budget ROM/RAM/Bank Switching Cartridge, Budget Programmer.

    7 parts8
  • 2 layers14.8 × 21.6 mmAdapter soic16, the printed circuit board in 3D

    Adapter soic16

    jypma/modsynth

    Open hardware eurorack synth modules

    3 parts8