Skip to the content
4 layers64 × 64 mmEspion cam, the printed circuit board in 3D

Multi-camera IR marker tracking: ESP32-P4/C5 firmware, Rust host, KiCad hardware

Size
64 × 64 mm
Copper layers
4
Thickness
1.62 mm
Parts
188
Nets
167
Pads
627
Tracks, vias
1,513, 328
Pours
94
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 Oct 2026
Updated
7 Nov 2026

Overview

Espion cam is an open-source printed circuit board by azais-corentin, from the azais-corentin/espion repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 64 × 64 mm with 188 parts on 167 nets, routed with 1,513 tracks and 328 vias.

It is built around the DP1435-5V, IP101GRI and TLV62569DBVR-TP, with the TLV9061IDBVR-MS, TPS61170DRVR and MSA3S02 among its other parts. Its parts include 76 resistors, 51 capacitors, 15 diodes, 12 ICs and 4 connectors. It belongs with the ESP32 and RISC-V boards of this library.

Main components

12

README

hardware/espion-cam/README.md

espion-cam

KiCad project for the espion camera board: a baseboard for the Waveshare ESP32-P4-Core module. The schematic is captured and ERC clean: a root sheet and seven hierarchical sheets (power, mcu, ethernet, camera, led_driver, led_ring, imu), with the multi-signal interfaces crossing sheets as buses. The board is fully placed and routed (4 layers, 64 × 64 mm, JLCPCB Economic PCBA on the top side, hand-soldered parts listed in .omp/kicad.json). Licensed under CERN-OHL-P-2.0 (../LICENSE).

Board

  • MCU: U6 Waveshare ESP32-P4-Core module (bottom side, hand-soldered, not on the stencil). Symbol MCU_Module_Waveshare:ESP32-P4-Core, footprint Module_Waveshare:Waveshare_ESP32-P4-Core_HandSolder (../lib/). mcu
  • Camera: off-board OV9281 global-shutter mono module behind a lens cutout, on a 15-pin 1.0 mm FFC (MIPI CSI-2, 2 lanes) through a notch in the board edge into J4 (AFA07 family, bottom contact). XVS (GPIO7) and STROBE come from the module's pads over a JST-SH 4-pin pigtail into J3: XVS through the R40/R44 divider, an assembly option; STROBE through U7 SN74LV1T34 to the LED gate and GPIO12 (ETM capture). A 0 Ω link on each CSI line at the FFC end (R45–R47, R49–R51). camera
  • LED: 850 nm ring D4–D15, 12 × A-SC880IR3C in one string around the lens cutout. U8 TPS22918 load switch (LED_PWR_EN, GPIO20), U10 TPS61170 boost (BST_EN, GPIO53; PWM sets the output) into the storage capacitors C46/C47, U11 TLV9061 + Q1 IRLR024N current sink (R69 sense) gated by STROBE ∧ LED_EN in U9 SN74LVC1G97 (LED_EN, GPIO11), with a hardware timeout per pulse behind the firmware exposure cap. No continuous-on mode. Firmware keeps +32V just above the string from a divider on Q1's drain (R70/R76, LED_K_SENSE, GPIO23); a +32V divider (R71/R72, VLED_SENSE, GPIO21) watches the rail. led
  • Ethernet: U1 IP101G PHY on RMII (Y1 crystal; the PHY supplies the REF_CLK), J1 HR871150C MagJack (bottom side, hand-soldered) with both centre taps and the spare pairs brought out, its LEDs driven by the PHY, PPS and PHY reset test points. PHY_RST_N GPIO22. ethernet
  • Power: U2 DP1435-5V IEEE 802.3af PoE PD module (isolated, bottom side, hand-soldered) through an LC filter (L1, C13, C14), OR-ed with USB-C 5 V by U4 TPS2121 priority mux (source on PWR_SRC, GPIO2); U3 TLV62569 buck to 3.3 V. power
  • USB-C: J2 straight to the P4's USB Serial/JTAG (no hub, GPIO24/25), U5 USBLC6-2SC6 ESD protection, D2 TSD05 VBUS TVS. VBUS is sensed on GPIO6 (VBUS_SENSE, R27/R28 divider): firmware turns the D+ pull-up off while no USB host supplies VBUS. mcu
  • Status and buttons: D1 YY-0807BRGK26 RGB status LED (STATUS_LED, GPIO13); SW1 RESET and SW2 BOOT (BOOT with D16 TSD05 ESD clamp). mcu
  • IMU: U12 MSA3S02 3-axis accelerometer on its own I²C bus (GPIO3/4), INT1 on GPIO51: the motion interrupt flags a bumped camera, the accelerometer gives the gravity vector for rig calibration (no gyroscope). imu
  • Mechanical: 4 × M3 plated mounting holes H1–H4, each pad on GND, kept clear of the PoE cable-side copper; 3 NPTH tooling holes TOOL1–TOOL3 (board-only) for JLCPCB Economic PCBA. layout

Assembly: everything on the top side is machine-placed by JLCPCB Economic PCBA except the hand-assembly list (assembly.hand in .omp/kicad.json; reasons in layout).

Board design (decisions, requirements and their reasons, formulas, layout constraints, firmware rules, the checks for the first boards): docs/hardware/.

The parts list is the schematic: every sourced symbol carries Manufacturer, MPN and LCSC fields, and the project's BOM preset Order exports them. Read it with kicad_query bom, or generate the CSV for each order (from this directory) and don't commit it:

sh
kicad-cli sch export bom --preset Order -o espion-cam-bom.csv espion-cam.kicad_sch

The CSV has the columns Reference, Qty, Value, Footprint, Manufacturer, MPN, LCSC and DNP, one row per group of identical parts, without DNP parts or parts excluded from the BOM.

Net classes (track widths, clearances, diff-pair geometry) are set in espion-cam.kicad_pro for the JLCPCB JLC04161H-7628 stack-up (4 layers, 1.6 mm). The spacing rules that net classes can't express (PoE isolation, MIPI CSI spacing and skew, MDI spacing, pair-to-pair spacing and skew, LED_PWR pad spacing, the U12 LGA lands, hole spacing, power neck-downs and silkscreen) are in the custom rules file espion-cam.kicad_dru; layout gives each one's reason.

System view: ../../docs/architecture.md. Timing requirements for XVS, STROBE and PPS: ../../docs/timing.md.

Conventions

  • Edit only with KiCad (the dev shell provides KiCad 10). Never hand-edit .kicad_* files. Agents work through the KiCad toolkit instead (kicad_query, kicad_edit, kicad_check, kicad_render, kicad_export; see ../../AGENTS.md).
  • The schematic and the board are the source of every value. docs/hardware/ holds requirements, decisions, formulas, accepted risks, layout constraints, firmware rules and first-board checks, never values the KiCad files hold or that are calculated from them. A change updates ../../docs/hardware/ in the same commit when it changes one of those. A part change also updates the symbol's Manufacturer, MPN and LCSC fields. A new or removed block or IC family updates the board list above. There is no committed BOM file.
  • Keep ERC at 0 violations: kicad-cli sch erc espion-cam.kicad_sch (from this directory).
  • Project-specific symbols, footprints and 3D models go in ../lib/ (conventions and KLC checks in ../lib/README.md), not in global libraries.
  • Fabrication outputs (Gerbers, drill files, BOM/CPL exports) and KiCad's .history/ are not committed. Generate the outputs for each release (kicad_export writes them to fab/).

Parts

188
QtyValueFootprintReferences
20100nF 50VCapacitor_SMD:C_0402_1005MetricC3, C12, C19, C21, C23, C24, C25, C26, C28, C30, C31, C37, C38, C44, C49, C50 +4
12A-SC880IR3CLED_SMD_Amicc:LED_Amicc_A-SC880IR3C_3.85x3.85mmD4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15
1010.0k 1%Resistor_SMD:R_0402_1005MetricR8, R26, R29, R33, R38, R48, R58, R66, R72, R76
10100k 1%Resistor_SMD:R_0402_1005MetricR17, R18, R20, R24, R56, R57, R59, R62, R68, R70
922 1%Resistor_SMD:R_0402_1005MetricR11, R12, R13, R15, R31, R32, R35, R36, R37
710uF 25VCapacitor_SMD:C_0805_2012MetricC4, C10, C11, C15, C18, C32, C36
60Resistor_SMD:R_0402_1005MetricR45, R46, R47, R49, R50, R51
65.1k 1%Resistor_SMD:R_0402_1005MetricR1, R7, R9, R10, R23, R25
4220 1%Resistor_SMD:R_0402_1005MetricR4, R5, R30, R67
4M3MountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
30Resistor_SMD:R_0805_2012MetricR34, R52, R53
31.00k 1%Resistor_SMD:R_0402_1005MetricR39, R54, R64
31.8k 1%Resistor_SMD:R_0402_1005MetricR41, R42, R44
310nF C0G 50VCapacitor_SMD:C_0603_1608MetricC33, C35, C41
34.7uF 25VCapacitor_SMD:C_0805_2012MetricC8, C16, C29
347k 1%Resistor_SMD:R_0402_1005MetricR19, R27, R43
3GNDTestPoint:TestPoint_Loop_D2.50mm_Drill1.0mmTP2, TP3, TP7
3ToolingHole_1.152mm_JLCPCBMountingHole_JLCPCB:ToolingHole_1.152mm_JLCPCBTOOL1, TOOL2, TOOL3
21.00M 1%Resistor_SMD:R_0402_1005MetricR63, R75
21.5k 1%Resistor_SMD:R_0402_1005MetricR14, R40
218pF C0GCapacitor_SMD:C_0402_1005MetricC2, C5
21nF C0GCapacitor_SMD:C_0402_1005MetricC40, C48
21uF 100VCapacitor_SMD:C_1206_3216MetricC43, C45
21uF 50VCapacitor_SMD:C_0805_2012MetricC27, C34
22.2uHInductor_SMD:L_Changjiang_FXL0630L1, L2
2220pF C0GCapacitor_SMD:C_0402_1005MetricC39, C42
2255k 1%Resistor_SMD:R_0603_1608MetricR65, R71
2330uF 50VCapacitor_SMD:CP_Elec_10x10C46, C47
24.7k 1%Resistor_SMD:R_0402_1005MetricR73, R74
2499kResistor_SMD:R_1206_3216MetricR2, R3
2TSD05DYFRDiode_SMD:D_SOD-323_HandSolderingD2, D16
1+32VTestPoint:TestPoint_Pad_D1.5mmTP13
1+3V3TestPoint:TestPoint_Pad_D1.5mmTP4
1+5VTestPoint:TestPoint_Pad_D1.5mmTP5
10.1 1% 100ppmResistor_SMD:R_1206_3216MetricR69
11.40k 1%Resistor_SMD:R_0402_1005MetricR61
1100uF 25VCapacitor_SMD:CP_Elec_6.3x5.8C22
110uHInductor_SMD:L_Changjiang_FNR4030SL3
11nF 2kVCapacitor_SMD:C_1206_3216MetricC1
125MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1330uF 16VCapacitor_SMD_AISHI:CP_Elec_6.3x9C13
1330uF 16VCapacitor_SMD_JIERR:CP_Elec_8x10.5C14
136k 1%Resistor_SMD:R_0402_1005MetricR22
1453k 1%Resistor_SMD:R_0402_1005MetricR16
147uF 10VCapacitor_SMD:C_1206_3216MetricC20
151.1k 1%Resistor_SMD:R_0402_1005MetricR60
16.19k 1%Resistor_SMD:R_0402_1005MetricR6
16.8pF C0GCapacitor_SMD:C_0402_1005MetricC17
160.4k 1%Resistor_SMD:R_0402_1005MetricR21
168k 1%Resistor_SMD:R_0402_1005MetricR55
175k 1%Resistor_SMD:R_0402_1005MetricR28
1AFA07-S15FCA-00Connector_FFC-FPC_JUSHUO:JUSHUO_AFA07-S15FCA-00_1x15-1MP_P1.0mm_HorizontalJ4
1BOOTButton_Switch_SMD_XKB:SW_Push_1P1T_XKB_TS-1187ASW2
1CAM_3V3TestPoint:TestPoint_Pad_D1.0mmTP10
1DP1435-5VConverter_DCDC_SDAPO:Converter_DCDC_SDAPO_DP1435_THTU2
1ESP32-P4-CoreModule_Waveshare:Waveshare_ESP32-P4-Core_HandSolderU6
1HR871150CConnector_RJ_HanRun:RJ45_HanRun_HR871150C_HorizontalJ1
1IP101GRIPackage_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.65x2.65mmU1
1IRLR024NPackage_TO_SOT_SMD:TO-252-2Q1
1ISNSTestPoint:TestPoint_Pad_D1.0mmTP14
1LED_ENTestPoint:TestPoint_Pad_D1.0mmTP11
1LED_ONTestPoint:TestPoint_Pad_D1.0mmTP12
1MSA3S02Package_LGA_MEMSensing:MEMSensing_LGA-12_2x2mm_P0.5mm_LayoutBorder2x4yU12
1NetTie_2NetTie_Courtyard:NetTie-2_SMD_Pad0.5mmNT1
1PHY_RST_NTestPoint:TestPoint_Pad_D1.0mmTP1
1PPSTestPoint:TestPoint_Pad_D1.0mmTP6
1RESETButton_Switch_SMD_XKB:SW_Push_1P1T_XKB_TS-1187ASW1
1SM04B-SRSS-TBConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ3
1SN74LV1T34DBVPackage_TO_SOT_SMD:SOT-23-5U7
1SN74LVC1G97DBVPackage_TO_SOT_SMD:SOT-23-6U9
1SS16Diode_SMD:D_SMAD3
1STROBETestPoint:TestPoint_Pad_D1.0mmTP9
1TLV62569DBVPackage_TO_SOT_SMD:SOT-23-5U3
1TLV9061Package_TO_SOT_SMD:SOT-23-5U11
1TPS2121RUXPackage_DFN_QFN_TI:Texas_RUX0012A_VQFN-HR-12_2x2.5mm_P0.5mmU4
1TPS22918DBVPackage_TO_SOT_SMD:SOT-23-6U8
1TPS61170DRVPackage_SON_TI:Texas_DRV0006A_WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mmU10
1TYPE-C-31-M-12Connector_USB_HRO:USB_C_Receptacle_HRO_TYPE-C-31-M-12J2
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U5
1XVS_CAMTestPoint:TestPoint_Pad_D1.0mmTP8

The 187 most common of 188 parts.

Similar boards

  • 6 layers203 × 151.8 mmPDNode Baseboard, the printed circuit board in 3D

    PDNode Baseboard

    DvidMakesThings/HW_PDNode-600-Pro

    The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.

    236 parts86AGPL-3.0
  • 4 layers152.3 × 72 mmIr glasses EVT E7, the printed circuit board in 3D

    Ir glasses EVT E7

    noahzhy/cc_glasses

    tools/ 为此次整改的重建和检查脚本;日常直接编辑 KiCad 工程。重建脚本会覆盖设计,不能在人工修改后直接重跑。Python 工具不引入继承类;需要 KiCad 10 的 pcbnew Python,以及 Python 3 的 sexpdata、numpy、scipy、shapely、pymupdf。

    171 parts1MIT
  • 4 layers40 × 24 mmSCH ESP32-P4 FUNCTION EV BOARD MIPI Camera Sub V1.1 20240529, the printed circuit board in 3D

    SCH ESP32-P4 FUNCTION EV BOARD MIPI Camera Sub V1.1 20240529

    OHNope/sc035hgs-esp32-p4x-camera-adapter-mod

    本仓库在 ESP32-P4XMIPICameraSubV1.1KiCAD(Espressif 官方相机转接板的 KiCad 转换版)基础上,修改为 SC035HGS 相机模组用的转接板。基础工程(导入修复、检查结果)的说明见它的 README。

    49 parts
  • 4 layers110 × 90 mmUsb hub 3s, the printed circuit board in 3D

    Usb hub 3s

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    116 parts3MIT
  • 4 layers100 × 100 mmNif T, the printed circuit board in 3D

    Nif T

    SharKingStudios/Nif-T

    An all in one smart home automation board!

    115 parts11MIT
  • 4 layers61 × 100 mmBigCore, the printed circuit board in 3D

    BigCore

    Dschadu/Geistwerk-BigCore

    An ESP32-based open hardware control board designed for Bottango-powered animatronic and motion projects.

    152 parts4CERN-OHL-W-2.0
  • 6 layers133 × 102 mmIasis, the printed circuit board in 3D

    Iasis

    hydazz/iasis

    An optional Raspberry Pi Compute Module 5 carrier for Iasis. It plugs into the main board's HubPD population and carries Ethernet, NVMe storage, an accessory USB-C port and a service USB-C port.

    723 partsApache-2.0

Questions

How big is the Espion cam PCB?

It measures 64 × 64 mm and has 4 copper layers, 1.62 mm thick.

What parts does the Espion cam use?

188 parts, built around the DP1435-5V, IP101GRI, TLV62569DBVR-TP and TLV9061IDBVR-MS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Espion cam KiCad files?

From the azais-corentin/espion repository on GitHub, at the commit this page was made from: the board is hardware/espion-cam/espion-cam.kicad_pcb and its schematic .omp/extensions/kicad/test/fixtures/board/board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Espion cam design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).