2 layers154.5 × 101 mm
4 layers50.5 × 80 mm
Basic
aep/artanis-light2vehicle gps tracker with battery ================================
- Size
- 50.5 × 80 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 147
- Nets
- 126
- Pads
- 521
- Tracks, vias
- 979, 335
- Pours
- 26
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 24 Feb 2021
- Updated
- 20 Mar 2021
Overview
Basic is an open-source printed circuit board by aep, from the aep/artanis-light repository on GitHub. It is a 4-layer board of 50.5 × 80 mm with 147 parts on 126 nets, routed with 979 tracks and 335 vias.
It is built around the ESP32-WROOM-32U, TCAN332D and AP63203WU, with the MMA8452QT, LM73100RPW and MCP73123-22SI/MF among its other parts. Its parts include 58 capacitors, 41 resistors, 12 ICs, 6 diodes and 5 connectors. It belongs with the ESP32 boards of this library.
Main components
12
ESP32-WROOM-32U
SMD,19.2x18mm-40℃~+85℃ -97dBm 2.4GHz 20.5dBm 3V~3.6V Bluetooth4.2 ESP32-DOWD UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC、CAN SMD,19.2x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
TCAN332D
SOIC-8-40℃~+125℃ 1Mbps 3V~3.6V 60mA CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
AP63203WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.3V 3.8V~32V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters
MMA8452QT
QFN-16(3x3)Attitude Sensor/GyroscopeNXP Semiconductors
LM73100RPW
VQFN-10-HR(2x2)-40℃~+125℃ 1 15V 2.7V~23V 28.4mV 426uA 44.85mΩ Integrated FET Reverse current blocking、Reverse polarity protection、Overvoltage lockout、Under-voltage lockout、Over temperature protection、Short-Circuit Protection、With enable VQFN-10-HR(2x2) ORing Controllers ROHSTexas InstrumentsPower Distribution Switches
MCP73123-22SI/MF
TDFN-10-EP(3x3)-40℃~+85℃ 1 1.1A 3.6V 4V~6.5V 4uA Charging IC LiFePO4 Battery DFN-10-EP(3x3) Battery Management ROHSMicrochip TechnologyBattery Management
TLV76750DRV
WSON-6(2x2)-40℃~+125℃@(Tj) 1 1.4V@(1A) 16V 1A 5V 60uVrms 70dB@(1kHz) 80uA Fixed Over Current Protection、Over Temperature Protection、Soft Start Positive WSON-6(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPS22810DRV
WSON-6-EP(2x2)-40℃~+105℃ 1 2.7V~18V 3A 79mΩ Active High Load Switch Undervoltage Protection(UVP)、Over Temperature Protection WSON-6-EP(2x2) Power Distribution Switches ROHSTexas InstrumentsPower Distribution SwitchesUSBLC6-4SC6
SOT-23-6-55℃~+125℃ 0.3pF 15V 300W@8/20us 4.7A@8/20us 5V 6V 80nA ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Unidirectional SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
APGA1602CGC/KA
0603-40℃~+85℃ 150° 2.05V 20mA 30mcd 48mW 571nm 573nm Discrete Diode Emerald Green Water Clear 0603 LED Indication - Discrete ROHSKingbrightLED Indication - Discrete
MMUN2233LT1G
SOT-231 NPN (Pre-Biased) 1.3V@5mA,0.3V 100mA 12 200mW 250MHz 300mV@5mA,0.25mA 500mV@100uA,5V 50V 6.11kΩ 80 NPN SOT-23 Digital Transistors ROHSTECH PUBLICDigital Transistors
0ZCF0050FF2C
2920-40℃~+85℃ 1.4Ω 1.5W 100A 1A 300mΩ 4s 500mA 60V 2920 Resettable Fuses ROHSBel FuseResettable Fuses
README
README.mdvehicle gps tracker with battery
- cpu: ESP32
- modem: Quectel BG96 minipcie
- supply: ~12V from vehicle
- battery: 2 14500 lifepo cells at 6.4V
Parts
147| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nF | Capacitor_SMD:C_0603_1608Metric | C7, C14, C15, C29, C33, C41, C42, C43, C44, C45, C47, C48, C57, C59 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R7, R15, R16, R17, R22, R23 |
| 7 | 1K | Resistor_SMD:R_0603_1608Metric | R13, R14, R24, R25, R32, R33, R39 |
| 7 | L0 | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5, TP8, TP9 |
| 6 | 10uF | Capacitor_SMD:C_0603_1608Metric | C26, C27, C30, C34, C46, C49 |
| 6 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C9, C11, C12, C22, C23, C40 |
| 6 | Fiducial | Aesthetics:FIDUCIAL-1X2 | FID1, FID2, FID3, FID4, FID5, FID6 |
| 6 | R0-DNP | Resistor_SMD:R_0603_1608Metric | R2, R4, R5, R18, R19, R38 |
| 5 | 100uF | Capacitor_SMD:C_1206_3216Metric | C50, C52, C54, C56, C58 |
| 5 | 10uF 50V | Capacitor_SMD:C_0805_2012Metric | C1, C2, C6, C10, C13 |
| 4 | 100nF 50V | Capacitor_SMD:C_0603_1608Metric | C3, C4, C8, C17 |
| 4 | 33pF | Capacitor_SMD:C_0603_1608Metric | C51, C53, C55, C60 |
| 4 | 56pf | Capacitor_SMD:C_0603_1608Metric | C35, C36, C37, C38 |
| 4 | R0 | Resistor_SMD:R_0603_1608Metric | R3, R26, R27, R29 |
| 3 | 100pF 50V | Capacitor_SMD:C_0603_1608Metric | C5, C19, C21 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R28, R30, R31 |
| 3 | 22R | Resistor_SMD:R_0603_1608Metric | R40, R41, R42 |
| 3 | 22uF 25V | Capacitor_SMD:C_0805_2012Metric | C16, C18, C20 |
| 2 | 22K | Resistor_SMD:R_0603_1608Metric | R34, R36 |
| 2 | 33pf | Capacitor_SMD:C_0603_1608Metric | C31, C32 |
| 2 | 5K | Resistor_SMD:R_0603_1608Metric | R35, R37 |
| 2 | 60R-DNP | Resistor_SMD:R_0603_1608Metric | R20, R21 |
| 2 | APGA1602CGC/KA | LED_SMD:LED_0603_1608Metric | D5, D6 |
| 2 | LM73100 | artanis-light:LM73100 | U4, U5 |
| 2 | MMUN2233LT1G | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 1 | 0ZCF0050FF2C | Fuse:Fuse_2920_7451Metric_Castellated | F1 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 10pF | Capacitor_SMD:C_0603_1608Metric | C61 |
| 1 | 1255AY-3R9N=P3 | 1255AY-3R9N_P3:IND_1255AY-3R9N=P3 | L1 |
| 1 | 3.9k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 33K | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 4.7nf-DNP | Capacitor_SMD:C_0603_1608Metric | C39 |
| 1 | 51K | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 68K | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | ACP3225-501-2P-T000 | aep:ACP3225 | FL1 |
| 1 | AP63203WU | Package_TO_SOT_SMD:TSOT-23-6 | U2 |
| 1 | APGA1602QBC/KA-5MAV | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | BLM18PG181SN1D | Capacitors:0603 | FB1 |
| 1 | Conn_01x02_Male | Connector_JST:JST_SH_SM02B-SRSS-TB_1x02-1MP_P1.00mm_Horizontal | J3 |
| 1 | Conn_01x02_Male | Connector_JST:JST_SH_BM02B-SRSS-TB_1x02-1MP_P1.00mm_Vertical | J2 |
| 1 | Conn_02x02_Top_Bottom | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J1 |
| 1 | ESP32-WROOM-32U | RF_Module:ESP32-WROOM-32U | U9 |
| 1 | M8AIG-16-12-2T3 | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | MBT3904DW1 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q1 |
| 1 | MCP2515-QFN | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U6 |
| 1 | MCP73123-22S | Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm | U3 |
| 1 | MMA8452Q | Silicon-Custom:QFN-16 | U8 |
| 1 | MSATA-PCIE_MINI-CARD-MM60-52B1-G1-R850(Digi-Key_PN_670-2516-2-ND) | OLIMEX_Connectors-FP:MM60-52B1-G1-R850 | CON1 |
| 1 | PE-1210ACC110STS 11UH | aep:PE-1210ACC | L2 |
| 1 | RS1GTR | Diode_SMD:D_SMA | D2 |
| 1 | SMBJ16CA-Q | Diode_SMD:D_SMB | D1 |
| 1 | SW_Push | aep:SW_1825027-5 | SW1 |
| 1 | SZNUP2105L | Package_TO_SOT_SMD:SOT-23 | D3 |
| 1 | TC2030_SWD | Connector:Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_Vertical | U10 |
| 1 | TCAN332 | Package_TO_SOT_SMD:SOT-23-8 | U7 |
| 1 | TLV76750 | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm_ThermalVias | U1 |
| 1 | TPS22810DRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U12 |
| 1 | USBLC6-4SC6 | Package_TO_SOT_SMD:SOT-23-6 | U13 |
| 1 | dummy | Aesthetics:OSHW-LOGO-S | X2 |
| 1 | dummy | aep:WEEE-Logo_2.1x3mm_SilkScreen | X1 |
| 1 | simcard | aep:nanosim-Wurth-693043020611 | J4 |
Questions
How big is the Basic PCB?
It measures 50.5 × 80 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Basic use?
147 parts, built around the ESP32-WROOM-32U, TCAN332D, AP63203WU and MMA8452QT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Basic KiCad files?
From the aep/artanis-light repository on GitHub, at the commit this page was made from: the board is basic.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Basic design in my own project?
Its repository states no licence, so its author keeps all rights: ask aep before reusing the design.
Similar boards
- 2 layers126 × 107 mm
- 2 layers190.9 × 152.8 mm
- 4 layers250.4 × 131 mm
Panel-16
geezacoleman/owl-driver-board
Development of a board that receives GPIO input and allows on/off control of connected solenoids.
939 parts14MIT - 4 layers100 × 60 mm
- 2 layers47.5 × 71.5 mm
ESP32 Wifi2CAN Rev0.1
ampnics/CAN-to-WiFi-Converter-Dongle-
CAN to WiFi Converter PCB using ESP32! This step-by-step tutorial covers schematic creation, PCB layout, and best practices for signal integrity. Perfect for automotive and IoT applications!
72 parts9 - 4 layers70 × 70 mm
- 4 layers70 × 70 mm
