Skip to the content
4 layers188.1 × 79 mmJacobi, the printed circuit board in 3D

48V at 50A with optimised colling

Size
188.1 × 79 mm
Copper layers
4
Thickness
1.6 mm
Parts
248
Nets
210
Pads
1,500
Tracks, vias
0, 0
Pours
2
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
23 Oct 2019
Updated
6 Nov 2026

Overview

Jacobi is an open-source printed circuit board by Tecnologic, from the Tecnologic/unimoc_jacobi repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 188.1 × 79 mm with 248 parts on 210 nets.

It is built around the STM32H743VIT6, TCAN334D and LM5109BMA, with the LMR12010YMK, LM5008 and LP2985-33DBVR among its other parts. Its parts include 100 resistors, 75 capacitors, 16 connectors, 15 diodes and 12 ICs. It belongs with the STM32 boards of this library.

Main components

11

README

README.md

Jacobi

36 V / 45 A (battery side, 100 A peak phase current) drive hardware of the unimoc project, with optimised cooling. Jacobi is the motor controller (logic board and power board); the firmware lives in the unimoc repository.

Board directory (firmware)boards/unimoc/jacobi/
Board nameunimoc_jacobi
Cyphal node nameorg.unimoc.jacobi
EESM variantJacobi E

Formerly hardware_4850.

Naming

The unimoc nodes are named after inventors. Moritz Hermann Jacobi built the first practical electric motor (1834, Königsberg) and drove a boat on the Neva with it (1838): the first electric motor put to practical use as a drive, which is what this board is for.

Drives

NameClassWho
Barlowsmall drivePeter Barlow, whose "Barlow's wheel" (1822) was one of the first electric motors: tiny but turning
Jacobi36 V / 45 A drive (this board, H7)Moritz Hermann Jacobi, first practical electric motor (1834) and electric boat on the Neva (1838)
Dolivobig driveMichail Dolivo-Dobrowolsky invented the three-phase motor and the three-phase system (AEG, 1889), the basis of every FOC drive

Other nodes

NameRoleWho
ZuseVDCKonrad Zuse built the first working programmable computer, so he's the brain
DraisPedal generatorKarl Drais invented the Laufmaschine (1817), the ancestor of the bicycle, powered by your own feet
MercatorSteeringthe map maker everyone navigates by
GutenbergDisplaymade information visible to everyone
VoltaBMS / batteryinvented the battery (the voltaic pile, 1800)
OttoThrottleNikolaus Otto, of the Otto engine: the classic gas pedal

Ratings and limits

What the hardware can do and where it stops. The numbers come from the datasheets and rough loss and thermal estimates (calculations below), not from measurements on a test bench. The reference load is the kids' quad: an MY1020 1600 W BLDC on 3 × 12 V lead-acid, which the controller already drives with 80 A peak phase current.

RatingLimited by
Battery3 × 12 V lead-acid (36 V), up to 44 V while charging; Li-ion up to 10S (42 V)60 V FETs (NCEP6080AG), see below
Enable input (J501 pin 3 against pin 4)12–40 V, switched battery voltage; 1–4 mA through a TLP291 optocoupler, 3750 Vrms isolationinput resistor R1115 (10k, 1206): 0.19 W at 44 V, 0.25 W rating
Battery current~45 A (1600 W at 36 V) for minutes in still air; continuous only with better coolinghousing to air: 1600 W needs about 58 A peak phase current
Phase current, peak100 A for secondsmotor saturation, FET losses
Phase current, continuous~50 A peak in still air; with the housing bolted to a frame or in airflow, the 100 A motor limit comes firsthousing to air (about 2.5 K/W)
Overcurrent trip120–130 Acurrent sensing range ±160 A
Not suitable for48 V systems (13S/14S Li-ion, 4 × 12 V lead-acid)60 V FET rating

Target motors

MotorSaturation (peak phase current)Fit
60 mm stator motors~100 Aup to the rating
Hoverboard hub motors~55 Aabout a third of the current range, fine resolution
MY1020 1600 W, 36 V (kids' quad)not published, estimated 80–100 Aruns today at 80 A peak

The MY1020 has no published saturation data. It can be measured with the controller: lock the rotor, run a DC current on the d or q axis in steps (0, 20, 40 … 120 A) and measure L = V / (di/dt) with a small voltage pulse. Saturation starts where L falls by 20–30 %. Above that current the motor gives little extra torque and mostly heat, so it is the useful current limit.

Bridge voltage: why 36 V

The bridge uses NCEP6080AG (NCE, LCSC C182469, DFN5×6-8L), two in parallel per switch, 12 per board. They are in stock and cost much less than an 80 V part. From the LCSC product page (the datasheet PDF was not reachable): 60 V, 80 A, R_DS(on) < 4.0 mΩ at 10 V (3.5 mΩ typ), < 5.0 mΩ at 4.5 V, Qg 67 nC, Coss 680 pF, 85 W, Tj up to 150 °C.

BatteryMax voltageMargin to 60 V
3 × 12 V lead-acid~44 V (charging)16 V: fine
10S Li-ion42 V18 V: fine
13S Li-ion54.6 V5 V: switching overshoot alone can use that, no
14S Li-ion / 4 × 12 V58.8 V / ~58 Vno

For 48 V the bridge needs 80 V FETs in the same footprint, e.g. the Infineon BSC040N08NS5 (80 V, 4.0 mΩ max, 121 A, marking 040N08NS), which sits on one of the existing prototype boards. Its R_DS(on) is the same as the NCE part; its lower gate charge (43 nC) only shortens the switching edges a little. The rest of the board already handles 48 V: the LM5008 supply runs from the battery up to 95 V, and the voltage dividers reach 73.8 V full scale.

Bridge losses

Two FETs in parallel per switch, sine current, 36 V, 20 kHz PWM, about 45 ns switching edges (LM5109B at about 1 A into 2 × 67 nC, 1R1 gate resistors). R_DS(on) is 4.0 mΩ max × 1.6 for Tj = 125 °C ≈ 6.4 mΩ. The factor 1.6 is taken from the BSC040N08NS5 curve because the NCE datasheet was not available; check it once the datasheet is in datasheets/.

Phase current (peak)Loss per FETLoss per phaseWhole bridge
50 A~1.3 W~5 W~16 W
80 A~3 W~12 W~36 W
100 A~4.5 W~18 W~54 W

Conduction per FET is I_rms² × R_DS(on) / 8 (the phase current splits over two FETs, and high and low side each conduct about half the time). Switching per phase is ½ × V × I_avg × (t_on + t_off) × f_PWM with I_avg = 2/π × I_peak.

Using one FET per switch instead of two would save 6 FETs and about 180 mm², but it doubles the conduction loss at the same current (about 16 W per FET at 100 A peak). In the closed housing that comes straight off the continuous current, so the board keeps two per switch.

PCB manufacturing

The board is made by JLCPCB: 4 layers, 1 oz copper on all layers (outer and inner), standard process. The design rules in jacobi.kicad_pro follow the JLCPCB 4-layer capabilities:

RuleValue
Min track width / clearance0.1 mm / 0.1 mm
Min via (diameter / drill)0.45 mm / 0.2 mm, annular ring 0.125 mm
Min copper to board edge0.3 mm
Min hole to hole / hole clearance0.25 mm
Min silk text1.0 mm high, 0.15 mm line

Net classes set the routing defaults (the high-current nets use pours, the track width is only for stubs and pad entries):

ClassTrack / clearance / viaNets
Power1.0 / 0.25 / 0.8 ⌀ 0.4 mm+BATT, GNDPWR, phase and switch nodes
GateDrive0.5 / 0.2 / 0.6 ⌀ 0.3 mm+12P, gate, HO/LO/HS/VSS, bootstrap
Dig Supply0.4 / 0.2 / 0.6 ⌀ 0.3 mm+12V, +3V3, +1V2, +BATT_LOGIC, GNDD, buck nodes
Analog Supply0.4 / 0.2 / 0.6 ⌀ 0.3 mm+3.3VA, +3.3VADC, GNDA, GND
Analog0.2 / 0.2 / 0.45 ⌀ 0.2 mmcurrent and voltage sense, temperature, ADC inputs
USB0.2 / 0.2 mm, pair gap 0.15 mmUSB_DP, USB_DM (impedance not yet checked)
Default0.15 / 0.15 / 0.45 ⌀ 0.2 mmeverything else

Cooling

The power board sits on an aluminium block the size of the board, which is mounted to the floor of the G113T housing (115 × 90 mm). Today the bottom copper is covered by solder mask, with thermal paste to the block and a thermal pad to the housing.

Step (per FET unless noted)RthNote
Junction → case~1 K/Wdatasheet class value
Thermal vias~3.3 K/W38 × 0.4 mm, 25 µm plating: the largest step from FET to block
Solder mask + paste~1 K/W20 µm mask, 50 µm paste over about 100 mm²
Junction → block~5.5 K/Wabout 17 K at 80 A peak, about 25 K at 100 A peak
Block → housing (pad, whole board)0.05–0.1 K/W3–5 K at 54 W
Housing → air (whole board)~2–3 K/W0.043 m² of housing in still air: sets the continuous current

At 80 A peak the bridge loses about 36 W. In still air the housing would end up far above any sensible temperature; it works because the peaks are short. The block and housing hold about 600 J/K (10 mm block assumed), a time constant of about 25 minutes, so 54 W (100 A peak) heats them by about 5 K per minute.

Continuous current for a block at ≤ 80 °C at 40 °C ambient (40 K):

Housing to airAllowed lossContinuous phase current
Still air, ~2.5 K/W~16 W~50 A peak
Bolted to the frame or in airflow, ~0.5 K/W~80 W~120 A peak, so the 100 A motor limit comes first

Improvements, biggest first:

  1. Housing to air. Bolt the housing to the vehicle frame or a metal plate with paste, or add fins or airflow. This is worth more than all other steps together.
  2. Thermal vias. Filled and capped vias (VIPPO) under the drain pad, as many as fit: about half the 3.3 K/W. The board stays 1 oz copper; the currents are carried by pours on all four layers, not by thicker copper.
  3. Block to housing. Thin paste on flat surfaces instead of the thermal pad, screws near the FET rows.
  4. Copper spreading. Large drain pours under each FET on the bottom and inner layers.

Keep the isolation. The bottom copper under the high-side FETs is at +BATT, under the low-side FETs it is the phase node, and the block conducts. The solder mask is the only insulation today. Opening the mask needs a defined insulator instead (25 µm polyimide film or a 0.15–0.2 mm ceramic-filled pad); thermally that is about the same as mask and paste, but the isolation is reliable. Avoid metal-filled pastes there.

Current sensing

One 0.5 mΩ 3920 shunt per phase (Yezhan DSLR-M-5-0.5F) in the phase output, with an INA240A1 (gain 20):

Range1.6 V / (20 × 0.5 mΩ) = ±160 A, 10 mV/A
Overcurrent trip120–130 A, above the 100 A motor saturation
Offset25 µV max at the input = 0.05 A; calibrated at start, drift 0.25 µV/K
Resolutionabout 0.08 A at 12 effective bits
Shunt loss1.6 W at 80 A peak, 2.5 W at 100 A peak (9 W part)

Other combinations that were considered:

Shunt + INA240RangeWhy not
0.4 mΩ + A1±200 Aonly needed for currents above 130 A, which the motors cannot use
0.2 mΩ + A2±160 Asame scaling, but 2.5× the offset in amps, and the A2 costs 1.60 € vs 0.25 € for a shunt
0.2 mΩ + A1±400 Acoarse at light load (about 0.2 A noise)

KiCad project

The logic board and the power board are combined in a single KiCad 10 project: jacobi.kicad_pro.

FileContent
jacobi.kicad_schRoot sheet with the two board sheets
logic.kicad_schLogic board: sub-sheets power_supply and controller; controller has the sub-sheets interfaces and analog
power.kicad_schPower board: sub-sheet phase, used three times for phase A/B/C
jacobi.kicad_pcbBoth boards side by side: logic board on the left, power board on the right
footprints/jacobi.prettyProject footprint library: enclosure RND 455-00370, the Kelvin footprint of the phase shunt R_Shunt_Yezhan_DSLR-5_3920_Kelvin, and LFPAK56_ThermalVias-1 and C_2220_5650Metric, which KiCad 10 no longer ships

Since both boards are in one PCB file, the net names are kept apart by the schematic hierarchy (/logic/..., /power/...). The board-to-board connectors (J101/J102/J111 on the logic board, J103/J104/J110 on the power board) are not joined electrically in the schematic, so each board keeps its own nets.

Schematic ahead of the PCB

The schematic is ahead of the PCB. The logic board will be laid out again; the PCB still shows the old F730 board.

  • MCU: STM32H743VIT6 (LQFP100, 2 MB flash, LCSC C114409) instead of the STM32F730R8. It sits on the controller sheet (now A3) and connects by net labels; the old wires end in labels of the same names. Added decoupling C613–C622; C603 is now 2.2 µF (VCAP). Pin plan and open points: docs/h743_logic_board.md.

  • Simple analog front end. The op-amp filters of the logic board are gone (the three current_filters sheets with low pass and AC high pass per phase, and the U701 filters for Vdc and the bridge NTC). What is left on the analog sheet:

    • Ia/Ib/Ic: 220R / 2n2 RC from the INA240 outputs (R717–R719, C713–C715)
    • Va/Vb/Vc: 220R / 2n2 RC (R720–R722, C716–C718), the same as the currents
    • Vdc: 4k7 / 10n RC (R705/C704)
    • +12P (gate driver supply): 4k7 / 10n RC (R723/C719)
    • bridge NTC: pull-up R703 with C701, then a 4k7 / 10n RC (R704/C703)
    • motor temperature unchanged

    The filter values are a first guess.

  • Voltage sensing on the power board. The dividers for the phase voltages and Vdc (47k / 2k2 0.1 %, with 1 nF; R101–R108, C101–C104) sit on the power board and go to the logic board over a third 2×5 connector, J110 → J111 (VSENSE). The old Vdc divider R701/R702/C702 on the logic board is gone.

  • Gate driver supply sense. A 10k / 2k2 divider (R109/R110, C105) on +12P at the drivers goes over pin 3 of the PWM connector (J103 → J101) to PC5. No 12 V is routed to the analog part.

  • Power board present. J110 pin 9 is GND on the power board; on the logic board it is pulled up (R612, 10k) to PE4 (PWR_DET, low = present).

  • Bridge NTC to GND on the power board. TH101 has its low side on the power board GND; only the high side goes through J104 pin 8. J104 pin 10 is now GND.

  • One shunt per phase. 0.5 mΩ 3920 (Yezhan DSLR-M-5-0.5F, LCSC C41382689) with Kelvin sense pads instead of three 2 mΩ 2512 in parallel, read by an INA240A1 (gain 20): ±160 A.

  • USB-C instead of mini-B: HRO TYPE-C-31-M-12 (LCSC C165948, 16 pins, USB 2.0), 5k1 on CC1/CC2 (R613/R614) as a device. SBU not connected.

  • PWM_EN through an optocoupler. The PWM_EN jumper J1102 is gone. The enable input is a TLP291 (U1102) on the interfaces sheet that pulls PE15 high. J501 (Enable, now 4-pin JST PH) carries, from pin 1: +BATT_LOGIC (battery +), the LM5008 supply (VIN), PWM_EN_IN (opto LED +, 12–40 V) and PWM_EN_RTN (opto LED return, battery −). The LED path is 10k (R1115) with 10n (C1108) across the LED and a 1N4148W (D1105) against reverse polarity. The output has a 510R collector resistor, a 10k pulldown (R1116) and 10n (C1109). PWM_EN_RTN is not connected to GNDD, so the enable line is isolated and its current stays in its own wire pair, which keeps noise out on a cart with four drives. Keep the LED side clear of copper from the output side under U1102 (5 mm creepage). On the bench bridge pins 1–2, put battery + on pin 3 and battery − on pin 4. On the cart switch pin 2 (logic) and pin 3 (phases).

  • +48V is now +BATT_LOGIC. The board is no longer 48 V compatible (60 V FETs), so the logic board supply net (J101 pin 1, J501 pin 1) is named after the battery. It stays a separate net from +BATT on the power board.

  • No aux bridge. The EESM excitation and brake chopper are out of scope for this board; a separate module will do that.

Production data

The production files of the PCB contain both boards. For separate production data per board, the old KiCad 5 data is in production/legacy_kicad5/ (as manufactured, with the op-amp filters, and the 2020 logic board BOM with prices).

Other folders

FolderContent
datasheets/Component datasheets
docs/Pictures of the logic board and the power board (old F730 boards), H743 logic board concept
mechanical/DXF exports of the power board, the cooler drawing, enclosure/ with STEP and DXF views of the RND 455-00370

Conversion notes (KiCad 5.1 → KiCad 10)

  • All symbols are updated from the KiCad 10 library; no KiCad 5 symbol graphics are left. The unused SolderJumper_2_Open was dropped. The old bitmaps of the other board on the logic and power sheets are removed.
  • The KiCad 5 schematic had other values than the PCB on the power board (the PCB was changed later). The schematic now follows the PCB: Qx01–Qx04 NCEP6080AG, Cx07/Cx09 56u, Rx03–Rx10 1R1. Their old Part# order numbers were removed and still have to be filled in.
  • Parts that KiCad 10 dropped or renamed:
    • Footprints LFPAK56_ThermalVias-1 and C_2220_5650Metric are now in the project library, copied from the PCB.
    • The 3D model of the 2220 capacitor now points to C_2220_5750Metric.
    • Symbols are relinked: Device:CP → Device:C_Polarized, Device:Ferrite_Bead_Small → Device:FerriteBead_Small, Device:Jumper_NO_Small → Jumper:Jumper_2_Small_Open.

Parts

248
QtyValueFootprintReferences
28100nCapacitor_SMD:C_0603_1608MetricC105, C202, C205, C302, C305, C402, C405, C502, C503, C506, C507, C601, C1101, C1102, C1103, C1104 +12
181R1Resistor_SMD:R_0603_1608MetricR203, R205, R207, R209, R303, R305, R307, R309, R403, R405, R407, R409, R606, R607, R608, R609 +2
1247kResistor_SMD:R_0603_1608MetricR211, R212, R213, R214, R311, R312, R313, R314, R411, R412, R413, R414
12NCEP6080AGjacobi:LFPAK56_ThermalVias-1Q201, Q202, Q203, Q204, Q301, Q302, Q303, Q304, Q401, Q402, Q403, Q404
12NetTie_2NetTie:NetTie-2_SMD_Pad0.5mmR204, R206, R208, R210, R304, R306, R308, R310, R404, R406, R408, R410
10510RResistor_SMD:R_0603_1608MetricR507, R1101, R1102, R1103, R1104, R1105, R1106, R1107, R1110, R1111
610nCapacitor_SMD:C_0603_1608MetricC515, C703, C704, C719, C1108, C1109
610uCapacitor_SMD:C_1206_3216MetricC201, C203, C301, C303, C401, C403
611kResistor_SMD:R_0603_1608MetricR503, R505, R601, R602, R603, R605
6220RResistor_SMD:R_0603_1608MetricR717, R718, R719, R720, R721, R722
62n2Capacitor_SMD:C_0603_1608MetricC713, C714, C715, C716, C717, C718
656uCapacitor_SMD:CP_Elec_10x10C207, C209, C307, C309, C407, C409
5SS110R3GDiode_SMD:D_SMAD201, D301, D401, D501, D505
410kResistor_SMD:R_0603_1608MetricR109, R510, R612, R1116
410ujacobi:C_2220_5650MetricC204, C304, C404, C501
41nCapacitor_SMD:C_0603_1608MetricC101, C102, C103, C104
422uCapacitor_SMD:C_1210_3225MetricC504, C508, C510, C511
42k2 0.1%Resistor_SMD:R_0603_1608MetricR102, R104, R106, R108
447k 0.1%Resistor_SMD:R_0805_2012MetricR101, R103, R105, R107
44k7Resistor_SMD:R_0603_1608MetricR604, R704, R705, R723
4GNDMountingHole:MountingHole_3.2mm_M3_ISO14580_PadH102, H103, H104, H107
30m5jacobi:R_Shunt_Yezhan_DSLR-5_3920_KelvinR201, R301, R401
311RResistor_SMD:R_0603_1608MetricR1108, R1109, R1114
31uCapacitor_SMD:C_0603_1608MetricC505, C1106, C1107
3GNDMountingHole:MountingHole_3.2mm_M3_Pad_ViaH101, H105, H106
3INA240A1PWRPackage_SO:TSSOP-8_4.4x3mm_P0.65mmU202, U302, U402
3LM5109BMAPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU201, U301, U401
2100kResistor_SMD:R_0603_1608MetricR502, R508
210k 0.1%Resistor_SMD:R_0603_1608MetricR703, R716
210uCapacitor_SMD:C_0805_2012MetricC514, C516
210uCapacitor_SMD:C_1210_3225MetricC606, C607
22u2Capacitor_SMD:C_0603_1608MetricC603, C620
24n7Capacitor_SMD:C_0603_1608MetricC509, C513
25k1Resistor_SMD:R_0603_1608MetricR613, R614
2PMLL4153Diode_SMD:D_MiniMELFD502, D506
1+jacobi:Terminal_M3_XFCN_TT34086077-0910J105
110kResistor_SMD:R_1206_3216MetricR1115
112VLED_SMD:LED_0603_1608MetricD504
11N4148WDiode_SMD:D_SOD-123D1105
1220kResistor_SMD:R_0603_1608MetricR501
122kResistor_SMD:R_0603_1608MetricR511
12k2Resistor_SMD:R_0603_1608MetricR110
12k7Resistor_SMD:R_0603_1608MetricR506
1330uInductor_SMD:L_Taiyo-Yuden_NR-80xx_HandSolderingL502
134kResistor_SMD:R_0603_1608MetricR504
13V3LED_SMD:LED_0603_1608MetricD503
13k3Resistor_SMD:R_0603_1608MetricR513
147RResistor_SMD:R_0805_2012MetricR509
14u7Inductor_SMD:L_1206_3216MetricL501
1Ajacobi:Terminal_M3_XFCN_TT34086077-0910J106
1ADCConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical_SMDJ104
1ADCConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_SMDJ102
1AINConnector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_HorizontalJ601
1AP2204K-5.0Package_TO_SOT_SMD:SOT-23-5U1103
1Bjacobi:Terminal_M3_XFCN_TT34086077-0910J107
1BTLDRJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP601
1BZT52C15Diode_SMD:D_SOD-123D507
1Cjacobi:Terminal_M3_XFCN_TT34086077-0910J108
1CAN_INConnector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_HorizontalJ1103
1CAN_OutConnector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_HorizontalJ1104
1ERRORLED_SMD:LED_0603_1608MetricD1102
1EnableConnector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_HorizontalJ501
1FWLED_SMD:LED_0603_1608MetricD1103
1Ferrite_Bead_SmallResistor_SMD:R_0603_1608MetricFB502
1GNDjacobi:Terminal_M3_XFCN_TT34086077-0910J109
1HALLConnector_JST:JST_PH_S5B-PH-K_1x05_P2.00mm_HorizontalJ1101
1Housing_Padjacobi:RND-455-00370N101
1LM5008Package_SO:MSOP-8_3x3mm_P0.65mmU502
1LMR12010YPackage_TO_SOT_SMD:SOT-23-6U501
1LP2985-33DBVRPackage_TO_SOT_SMD:SOT-23-5U503
1MOT_TEMPConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalJ701
1NTC 10kResistor_SMD:R_0603_1608MetricTH101
1PWMConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_SMDJ101
1PWMLED_SMD:LED_0603_1608MetricD1104
1PWMConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical_SMDJ103
1Q33310F70051500Oscillator:Oscillator_SMD_Abracon_ASE-4Pin_3.2x2.5mmX601
1RUNLED_SMD:LED_0603_1608MetricD1101
1STM32H743VIT6Package_QFP:LQFP-100_14x14mm_P0.5mmU601
1SWDConnector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_VerticalP1101
1TCAN334Package_TO_SOT_SMD:SOT-23-8U1101

The 244 most common of 248 parts.

Similar boards

  • 4 layers83 × 86.5 mmBTS MainBoard Power, the printed circuit board in 3D

    BTS MainBoard Power

    bebenlebricolo/BTS-MainBoard-Power

    Beer thermoregulation system mainboard - power section

    94 partsGPL-3.0
  • 2 layers104.1 × 83.8 mmSystem voltages, the printed circuit board in 3D

    System voltages

    kt140/ECE445_SeniorDesign

    This is the senior design project for Kanin Tangchartsiri, Lukas Gollings, and Wonjoon Lee.

    48 parts
  • 4 layers53 × 70 mmODrive, the printed circuit board in 3D

    ODrive

    Sasasu/ODrive

    162 parts
  • 2 layers55.2 × 39.7 mmBuck, the printed circuit board in 3D

    Buck

    WidRojas/PCB-Hardware-Projects

    Repo containing all PCB files alongside short project descriptions

    37 parts
  • 2 layers200 × 120 mmPlytka v2, the printed circuit board in 3D

    Plytka v2

    tmierzwa/WICI

    Otwarty system łączności awaryjnej (Reticulum/LXMF, 869 MHz)

    152 parts4
  • 6 layers46.5 × 47.2 mmNAVCORE SoOP, the printed circuit board in 3D

    NAVCORE SoOP

    kfilipekk/iridium_drone

    STM32H743 flight controller that navigates without GPS from Iridium satellite Doppler

    217 parts2MIT
  • 6 layers268 × 230 mmRf board, the printed circuit board in 3D

    Rf board

    PE1RGU/hf-antenna-switch

    Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.

    357 parts2CERN-OHL-S-2.0

Questions

How big is the Jacobi PCB?

It measures 188.1 × 79 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Jacobi use?

248 parts, built around the STM32H743VIT6, TCAN334D, LM5109BMA and LMR12010YMK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Jacobi KiCad files?

From the Tecnologic/unimoc_jacobi repository on GitHub, at the commit this page was made from: the board is jacobi.kicad_pcb and its schematic analog.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Jacobi design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).