

Electrical power system
- Size
- 90.2 × 95.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 134
- Nets
- 187
- Pads
- 543
- Tracks, vias
- 942, 95
- Pours
- 419
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 21 Jun 2023
- Updated
- 25 Jul 2023
Overview
Electrical power system is an open-source printed circuit board by SkCubeSat, from the SkCubeSat/electrical-power-system-hardware repository on GitHub. It is a 2-layer board of 90.2 × 95.9 mm with 134 parts on 187 nets, routed with 942 tracks and 95 vias.
It is built around the ATMEGA328-PU, TPS630701RNMT and CSD16406Q3. Its parts include 41 resistors, 28 capacitors, 14 connectors, 12 ICs and 10 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)TPS630701RNMT
VQFN-15(2.5x3)-40℃~+125℃@(TJ) 1 2.4MHz 2A 2V~16V 50uA 5V Buck-Boost Buck-Boost Built-in Fixed Yes VQFN-15(2.5x3) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersCSD16406Q3
VSON-8(3.3x3.3)-55℃~+150℃ 1 N-channel 1.1nF 2.2V 25V 46W 7.4mΩ@4.5V 79A 8.1nC@4.5V 80pF 950pF N-Channel VSON-8(3.3x3.3) MOSFETs ROHSTexas InstrumentsMOSFETs
Parts
134| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 5M | Resistor_SMD:R_0603_1608Metric | R27, R28, R31, R32, R35, R36, R39, R40 |
| 8 | CSD16406Q3 | SamacSys_Parts:DQG_VSON-CLIP | Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10 |
| 7 | 330 | Resistor_SMD:R_0603_1608Metric | R22, R23, R24, R29, R33, R37, R41 |
| 6 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C17, C18, C25, C26, C27, C28 |
| 6 | 22u | Capacitor_SMD:C_0805_2012Metric | C11, C12, C13, C14, C15, C16 |
| 6 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J2, J3, J4, J5, J6 |
| 6 | D_Schottky | Diode_THT:D_A-405_P10.16mm_Horizontal | D1, D2, D3, D4, D5, D6 |
| 6 | SW_Push_SPDT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW2, SW3, SW4, SW5, SW6, SW7 |
| 5 | 100k | Resistor_SMD:R_0603_1608Metric | R4, R9, R10, R13, R15 |
| 4 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C19, C22, C23, C24 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R19, R21 |
| 4 | 10u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4 |
| 4 | 10u | Capacitor_SMD:C_0603_1608Metric | C5, C6, C9, C10 |
| 4 | 2.2k | Resistor_SMD:R_0603_1608Metric | R26, R30, R34, R38 |
| 4 | BQ297xy | Package_SON:WSON-6_1.5x1.5mm_P0.5mm | U7, U8, U9, U10 |
| 4 | Battery_Cell | footprints:18650_TH | BT1, BT2, BT3, BT4 |
| 4 | Conn_01x05_Pin | Connector_Hirose:Hirose_DF13-05P-1.25DSA_1x05_P1.25mm_Vertical | J7, J8, J9, J11 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_ISO7380_Pad_TopBottom | H1, H2, H3, H4 |
| 3 | 150k | Resistor_SMD:R_0603_1608Metric | R6, R14, R16 |
| 2 | 0.001 | SamacSys_Parts:WSL27261L000FEA | R11, R12 |
| 2 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 2 | 1.5u | Inductor_SMD:L_Bourns-SRN4018 | L1, L2 |
| 2 | 2k | Resistor_SMD:R_0603_1608Metric | R17, R18 |
| 2 | Conn_02x26_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x26_P2.54mm_Vertical | J10, J12 |
| 2 | INA180 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U2, U3 |
| 2 | Jumper_2_Open | Resistor_SMD:R_0603_1608Metric | JP1, JP2 |
| 2 | TPS630701RNMT | SamacSys_Parts:TPS630701RNMT | IC1, IC2 |
| 1 | 0.01u | Capacitor_SMD:C_0402_1005Metric | C20 |
| 1 | 1.65k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10u | Capacitor_THT:CP_Radial_D4.0mm_P1.50mm | C21 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 130k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 4.7k | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 680k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | ATmega328-P | Package_DIP:DIP-28_W7.62mm | U5 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J14 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J13 |
| 1 | LOGO | USST_logo:usask_logo_20x4 | G*** |
| 1 | LOGO | footprints:USSTfoot | G*** |
| 1 | LOGO | USST_logo:u_of_r_logo_20x8 | G*** |
| 1 | LT1762-3.3 | Package_SO:MSOP-8_3x3mm_P0.65mm | U4 |
| 1 | LTC4054XES5-4.2 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | NMOS | Package_TO_SOT_SMD:SOT-23-3 | Q1 |
| 1 | PMOS | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | SW_Push_SPDT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | SW1 |
| 1 | TCAN1043xDxQ1 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U6 |
The 133 most common of 134 parts.
Similar boards
- 4 layers100 × 60 mm

- 4 layers71 × 64 mm

UWB
victorstoica114/UWB_Module_ESP_IDF
ESP-IDF 6.0.2 firmware for the custom UWB Module V1.0 Rev.B, based on an ESP32-S3-WROOM-1-N16R8. The same application image runs on every module; persistent identity and runtime configuration select the role and active…
254 parts1 - 4 layers95.9 × 90.2 mm

KENSAT EPS v1.2
kenchangh/kensat
KENSAT, Edge-AI Compute in Orbit - A 2U CubeSat that runs a large language model on-orbit. A power-gated NVIDIA Jetson Orin Nano executes neural-network inference in space, and the results are downlinked over a custom…
218 parts119 - 4 layers90.2 × 96 mm

- 4 layers150 × 100 mm

Interrupter v1.2
Alberto0235/DRSSTC-Fiber-Optic-Interrupter
Custom 4-layer interrupter control board for DRSSTC systems. STM32F405-based, fiber-optically isolated outputs, hardware E-brake safety chain, and controlled-impedance routing (90Ω USB, 50Ω FSMC/SDIO).
212 partsMIT - 2 layers116.5 × 101.7 mm

- 4 layers50 × 38.9 mm

ESP32CAM Weather Station
EliaKr/ESP32CAM-Weather-Station
[WIP] This repo includes electronics (schematics/PCBs), 3D-printable mechanical parts, and software for a custom ESP32-CAM weather station.
96 partsGPL-3.0 - 2 layers25.1 × 5.6 mm

Questions
How big is the Electrical power system PCB?
It measures 90.2 × 95.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Electrical power system use?
134 parts, built around the ATMEGA328-PU, TPS630701RNMT and CSD16406Q3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Electrical power system KiCad files?
From the SkCubeSat/electrical-power-system-hardware repository on GitHub, at the commit this page was made from: the board is CUBICS/electrical-power-system/electrical-power-system/electrical-power-system.kicad_pcb and its schematic CUBICS/electrical-power-system/electrical-power-system/buck_converters.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Electrical power system design in my own project?
Its repository states no licence, so its author keeps all rights: ask SkCubeSat before reusing the design.