2 layers273 × 146 mm
PS2BaseMount
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
98 parts
2 layers
PreControlChip
MRKane05/PS2BaseMountThe KiCad project for the base mount for the "Junkstation" PS2 portable project
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 19
- Nets
- 186
- Pads
- 264
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Dec 2024
- Updated
- 11 Dec 2024
Overview
PreControlChip is an open-source printed circuit board by MRKane05, from the MRKane05/PS2BaseMount repository on GitHub. It is a 2-layer board with 19 parts on 186 nets.
It is built around the RJ45. Its parts include 8 ICs and 6 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
1README
README.mdThis is a dump of the KiCad project for the Junkstation PS2 project I made a few years ago. I'm really just backing it up for prosperity. I'm taking no responsibility for this and it really should be used only as reference.
It's worth noting that there are a couple of mistakes on the board that I haven't fixed: -The Ethernet wiring for the Mango isn't correct, and troubleshooting it was exceedingly difficult, so much so that I didn't write it down when I got it right, I just put the lid on it -The Ethernet lines for the Mango shouldn't be pulled down to Ground but pulled to the "R0" pin on the Mango. This allows a successful ethernet connection -The SD Card slot wired up for game loading through the memory card port is correctly wired
Parts
19| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | PS2_ControlMount | PS2BaseMount:PS2_BoardMountFootprint | P1, P2 |
| 1 | 5VBuckBoost | PS2BaseMount:PS2BuckBoost | U2 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano_WithMountingHoles | A1 |
| 1 | AudioAmp | PS2BaseMount:PAM8803_AudioAmp | U1 |
| 1 | Audio_Left | Connector_JST:JST_ZE_SM02B-ZESS-TBT_1x02-1MP_P1.50mm_Horizontal | U4 |
| 1 | Audio_Right | Connector_JST:JST_ZE_SM02B-ZESS-TBT_1x02-1MP_P1.50mm_Horizontal | U5 |
| 1 | DMosfet_AO9926B | PS2BaseMount:DualMosfet AO9926B | U8 |
| 1 | NanoPiDUO2 | NanoPI_Duo2-master:NanoPIDUO2 | U7 |
| 1 | PJ30240 | PS2BaseMount:AudioJack_PJ30240 | U3 |
| 1 | PS2AVPort | PS2BaseMount:PS2_AVPort_Complete | M1 |
| 1 | PS2AVPort_SideMount | PS2BaseMount:PS2_AVPort_Complete_MountSilk | M5 |
| 1 | PS2_MemCardMount | PS2BaseMount:PS2_MemCardMountPoints | P3 |
| 1 | RJ45 | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J3 |
| 1 | TS_LFT | Connector_JST:JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | M2 |
| 1 | TS_RHT | Connector_JST:JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | M3 |
| 1 | USB_A_Dual | Connector_USB:USB_A_Wuerth_61400826021_Horizontal_Stacked | J2 |
| 1 | USB_B | PS2BaseMount:USB_A_Custom_Throughhole | J1 |
| 1 | XOST_Buttons | PS2BaseMount:XOST_Buttons | U6 |
More from MRKane05/PS2BaseMount
3- 2 layers
PS2BaseMount NanoPi
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
58 parts - 2 layers
PS2Board PreController
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
26 parts
Similar boards
- 2 layers33.7 × 97.8 mm
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 4 layers84 × 82 mm
Toad
travisgoodspeed/goodfet
An embedded bus adapter for various microcontrollers and radios.
241 parts333 - 2 layers100 × 100 mm
- 2 layers50 × 55.4 mm
- 2 layers67.9 × 47.8 mm
Platine
nv1t/standing-desk-interceptor
I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project
11 parts52CC0-1.0 - 4 layers90 × 75 mm
- 4 layers73.9 × 84.5 mm
Aei
Severson-Group/AMDC-Hardware
Circuit board designs for controlling advanced motor systems
54 parts51 - 2 layers99 × 60 mm
Pwr
mfkiwl/KiwiSDR_PCB
KiCAD PCB files for KiwiSDR project including active antenna and bias tee
64 parts46
Questions
What parts does the PreControlChip use?
19 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PreControlChip KiCad files?
From the MRKane05/PS2BaseMount repository on GitHub, at the commit this page was made from: the board is PreControlChip.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PreControlChip design in my own project?
Its repository states no licence, so its author keeps all rights: ask MRKane05 before reusing the design.