

KiCAD PCB files for KiwiSDR project including active antenna and bias tee
- Size
- 99 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 29
- Pads
- 146
- Tracks, vias
- 251, 36
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 29 Apr 2016
- Updated
- 20 Apr 2016
Overview
Pwr is an open-source printed circuit board by mfkiwl, from the mfkiwl/KiwiSDR_PCB repository on GitHub. It is a 2-layer board of 99 × 60 mm with 64 parts on 29 nets, routed with 251 tracks and 36 vias.
It is built around the LM2941T, MMBT4401 and RJ45. Its parts include 17 capacitors, 14 resistors, 10 connectors, 4 diodes and 2 inductors. It belongs with the radio and wireless boards of this library.
Main components
3LM2941T
TO-220-5-40℃~+125℃@(Tj) 0.003%Vout 1 10mA 1A 26V 500mV@(1A) 5V~20V Adjustable Positive Short Circuit Protection、Thermal shutdown、Enable control、Input overvoltage protection、Reverse polarity voltage protection TO-220-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHGSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMMBT4401
SOT-23-55℃~+150℃ 1 NPN 100nA 250MHz 350mW 400mV 40V 600mA 6V 80 NPN SOT-23 Bipolar (BJT) ROHSDiodes IncorporatedBipolar (BJT)RJ45
TH-12PTH-12P SMT ROHSJLCPCB AssemblyUncategorised
README
README.md[updated 20-April-2016]
Click image for full size.
KiwiSDR
Software-defined Radio (SDR) and GPS for the BeagleBone Black
An add-on board ("cape") that turns your Beagle into a web-accessible shortwave receiver.
This repository contains the KiCAD files (schematics, board layout), Gerbers, BOM and other files used to produce the KiwiSDR PCB. Also included here is the design for an active antenna and bias tee although they are still undergoing development.
The KiwiSDR software is located in the repository Beagle_SDR_GPS.
Kickstarter
KiwiSDR had a successful Kickstarter.
Details
- Listen live: New Zealand, Canada, Sweden, all others on SDR.hu
- Design review document
- Project status & history
- Schematic, Gerbers, Active antenna, BOM ODS, BOM XLS
Description
This SDR is a bit different. It has a web interface that can be used by up to four separate listeners. Each one listening and tuning an independent frequency simultaneously. See the screenshots below.
Components
- SDR covering the 10 KHz to 30 MHz (VLF-HF) spectrum.
- Web interface based on OpenWebRX from András Retzler, HA7ILM.
- Integrated software-defined GPS receiver from Andrew Holme's Homemade GPS Receiver.
- LTC 14-bit 65 MHz ADC.
- Xilinx Artix-7 A35 FPGA.
- Skyworks SE4150L GPS front-end.
Features
- 100% Open Source / Open Hardware.
- Includes VLF-HF active antenna and associated power injector PCBs.
- Browser-based interface allowing multiple simultaneous user web connections (currently 4).
- Each connection tunes an independent receiver channel over the entire spectrum.
- Waterfall tunes independently of audio and includes zooming and panning.
- Multi-channel, parallel DDC design using bit-width optimized CIC filters.
- Good performance at VLF/LF since I personally spend time monitoring those frequencies.
- Automatic frequency calibration via received GPS timing.
- Easy hardware and software setup. Browser-based configuration interface.
Status
Give the live receiver a try at the link above. You'll need a recent version of a modern web browser that supports HTML5. The web interface works, with lots of problems, on iPad. But there is no mobile version of the interface yet.
The files of a KiCAD PCB layout of the cape are available. This PCB has been fabricated in prototype quantities. Please email me any comments you have after reviewing the design document above (I need all the advice I can get). The active antenna and injector PCBs have been fabricated and are undergoing development.
Objectives
I wanted to design an SDR that provides certain features, at a low price point, that I felt wasn't covered by current devices. The SDR must be web-accessible and simple to setup and use.
I also want to provide a self-contained platform for experimentation with SDR and GPS techniques. In this respect the project has a lot in common with the recent HackRF and BladeRF Kickstarter projects.
Most importantly, I'd really like to see a significant number of web-enabled, wide-band SDRs deployed in diverse locations world-wide because that makes possible some really interesting applications and experiments.
Operation
The user will be required to purchase the Beagle, plug the SDR into the cape connectors, install a couple of software packages and open up an incoming port through whatever Internet router may exist. An antenna solution must also be provided although the included active antenna should help in this regard. A $10 GPS puck antenna will work fine. An adequate power supply to the Beagle (e.g. 5V @ 2A) will be required.
Four channels of audio and waterfall streamed over the Internet 24/7 requires about 30 GB per month. This is a common cap for many residential broadband plans. An automatic dynamic-DNS system is already part of the software so a web link to the SDR is immediately available with no configuration. Of course the system can be configured to only allow connections from the local network and ignore Internet connection requests.
Web interface screenshots
Click images for full size.
View of entire 0-30 MHz range:
Moderate zoom of medium-wave broadcast band with spectrum display on top enabled:
Over-the-horizon-radar (OTHR) from Cyprus showing short-term ionospheric fluctuations:
VLF/LF reception in New Zealand
| kHz | Station | Location | Signal |
|---|---|---|---|
| 12.88 | Alpha | Khabarovsk & Novosibirsk Russia | Navigation system |
| 17.0 | VTX2 | India | MSK comms |
| 19.8 | NWC | Australia | MSK comms |
| 21.4 | NPM | Hawaii | MSK comms |
| 22.2 | NDT/JJI | Japan | MSK comms |
| 24.1 | (UNID) | Korea, per David L Wilson | FSK comms |
| 40.0 | JJY | Japan | Time signal |
| 45.9 | NSY | Italy | MSK comms |
| 54.0 | NDI | Japan | MSK comms |
| 60.0 | JJY/WWVB | Japan, USA | Time signals |
| 68.5 | BPC | China | Time signal |
Many others heard during different times and conditions.
[end-of-document]
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 470n/100 | kiwi-SM1206 | C201, C202, C203, C212, C214, C215, C216 |
| 5 | 100n/100 | kiwi-SM0805 | C204, C205, C206, C207, C208 |
| 5 | TB_2 | kiwi-TB_2P_2_54MM | J20, J22, J24, J26, J28 |
| 4 | 47R | kiwi-SM0805 | R204, R205, R206, R207 |
| 4 | DNL | kiwi-SM0805 | R212, R214, R215, R217 |
| 4 | MTG_HOLE 3.5 MM | kiwi-MTG_NPTH_3_5MM | MTG1, MTG2, MTG3, MTG4 |
| 3 | SMA | kiwi-BNC_SMA_NO_VIP | J23, J25, J27 |
| 2 | 1K | kiwi-SM0805 | R203, R208 |
| 2 | 1n/100 | kiwi-SM0805 | C211, C213 |
| 2 | 330u/35 EL | kiwi-CAP_10x10 | C209, C217 |
| 2 | CMC 2 mH | kiwi-CMC | T201, T202 |
| 2 | FIDUCIAL | kiwi-FIDUCIAL | FID3, FID4 |
| 2 | PPTC 200 mA | kiwi-SM1812 | F201, F202 |
| 2 | TEST_POINT | kiwi-TP_1250 | TP201, TP202 |
| 2 | TVS 3.3V | kiwi-SOD323 | D203, D204 |
| 1 | 0R | kiwi-SM0805 | R213 |
| 1 | 100uH | kiwi-SM1812 | L201 |
| 1 | 11K5 | kiwi-SM0805 | R202 |
| 1 | 1K5 | kiwi-SM0805 | R216 |
| 1 | 20mH 1A | kiwi-CMC_22x22 | L202 |
| 1 | 22u/25 TA | kiwi-CAP_D | C210 |
| 1 | 680R | kiwi-SM0805 | R201 |
| 1 | BR 0.5A 400V | kiwi-TO269_AA | D201 |
| 1 | DC JACK 2.1MM | kiwi-DC_JACK_2_1MM | J29 |
| 1 | LM2941 | kiwi-TO263 | U201 |
| 1 | LOGO | kiwi-KIWI_10MM | GFX2 |
| 1 | MMBT4401 | kiwi-SOT23_BCE | Q201 |
| 1 | OSHW | kiwi-OSHW_6MM | GFX4 |
| 1 | RJ45 | kiwi-RJ45_8 | J21 |
| 1 | T-622 | kiwi-MCL_KK81 | T203 |
| 1 | TVS 25VAC | kiwi-SM0805 | D202 |
Similar boards
- 2 layers70 × 100 mm

- 2 layers290 × 100 mm

ESP32-Wall Clock
SkullKill/ESP32-Wall-Clock-PCB
ESP32 based 30cm Wall Mounted Clock. WiFi, NTP, SNMP, web interface, MicroUsb, Type-C, HG3613 Retrofit
207 parts3GPL-3.0 - 4 layers70 × 90 mm

- 2 layers101 × 76.2 mm

Boardlock
ECE477Group13/hardware_pcb
GitHub backup of PCB design files (Schematic and Board files)
131 parts - 4 layers120 × 46.3 mm

DragonYUV
jimbro1000/DragonPalAD724
Translation is performed per channel to calculate the relative R-Y and B-Y values that can be combined with an inverted Y signal to produce RGB. Each output channel can then be fine tuned for strength independently.
68 parts - 4 layers50.8 × 58.4 mm

Led ring driver
frc971/electrical
This repo contains the electrical files for the 971 FRC team. The files include PCBs and the electrical system diagrams. The PCBs are created using KiCad.
105 parts3Apache-2.0 - 4 layers449.2 × 272.9 mm

Board v4 pre v5
lolz0r/Williams-WPC-Power-Driver-Board-A-12697-3
Untested, unverifed, AI created design.
415 parts2 - 2 layers76.2 × 44.5 mm

Questions
How big is the Pwr PCB?
It measures 99 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pwr use?
64 parts, built around the LM2941T, MMBT4401 and RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pwr KiCad files?
From the mfkiwl/KiwiSDR_PCB repository on GitHub, at the commit this page was made from: the board is active_antenna_pwr/pwr.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pwr design in my own project?
Its repository states no licence, so its author keeps all rights: ask mfkiwl before reusing the design.

© bluebison.net


