2 layers
PS2BaseMount NanoPi
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
58 parts
2 layers273 × 146 mm
PS2BaseMount
MRKane05/PS2BaseMountThe KiCad project for the base mount for the "Junkstation" PS2 portable project
- Size
- 273 × 146 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 98
- Nets
- 189
- Pads
- 449
- Tracks, vias
- 762, 153
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Dec 2024
- Updated
- 11 Dec 2024
Overview
PS2BaseMount is an open-source printed circuit board by MRKane05, from the MRKane05/PS2BaseMount repository on GitHub. It is a 2-layer board of 273 × 146 mm with 98 parts on 189 nets, routed with 762 tracks and 153 vias.
It is built around the DS18B20, LM2596T-5.0 and PAM8403, with the RJ45 among its other parts. Its parts include 26 ICs, 17 resistors, 10 capacitors, 9 connectors and 7 diodes. It belongs with the PIC boards of this library.
Main components
4
DS18B20
TO-92-55℃~+125℃ 12bit 3V~5.5V 750ms Single-bus ±0.4℃ TO-92 Temperature Sensors ROHSUMWTemperature Sensors
LM2596T-5.0
TO-220-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-220-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
PAM8403
SOP-16-40℃~+85℃ 2-Channel 2.2V~5.5V 3Wx2@4Ω 6.3mA 90% Automatic mute/no-noise switch、Enable/shutdown function、Filterless architecture Class D SOP-16 Audio Amplifiers ROHSSlkorAudio Amplifiers
RJ45
TH-12PTH-12P SMT ROHSJLCPCB AssemblyUncategorised
README
README.mdThis is a dump of the KiCad project for the Junkstation PS2 project I made a few years ago. I'm really just backing it up for prosperity. I'm taking no responsibility for this and it really should be used only as reference.
It's worth noting that there are a couple of mistakes on the board that I haven't fixed: -The Ethernet wiring for the Mango isn't correct, and troubleshooting it was exceedingly difficult, so much so that I didn't write it down when I got it right, I just put the lid on it -The Ethernet lines for the Mango shouldn't be pulled down to Ground but pulled to the "R0" pin on the Mango. This allows a successful ethernet connection -The SD Card slot wired up for game loading through the memory card port is correctly wired
Parts
98| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | R10K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R11, R12, R13, R17, R18, R19 |
| 5 | 2N7000 | PS2BaseMount:2N7000_HandSolder | Q1, Q3, Q4, Q5, Q6 |
| 5 | GNDMount | PS2BaseMount:GND | U7, U16, U24, U25, U26 |
| 3 | 470n | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C2, C3, C9 |
| 3 | C1u | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C4, C5, C6 |
| 2 | 100K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R1, R4 |
| 2 | 18650_BatteryMount | PS2BaseMount:18650_3xHolderV3 | U11, U12 |
| 2 | 1K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R2, R6 |
| 2 | Conn_01x06_Female | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | J2, J8 |
| 2 | PS2_ControlMount | PS2BaseMount:PS2_BoardMountFootprint | P2, P3 |
| 2 | R100K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R14, R15 |
| 2 | R220 | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R8, R9 |
| 2 | RJ45 | PS2BaseMount:RJ45_Floating | J1, J5 |
| 1 | 10U | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C1 |
| 1 | 220 | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R10 |
| 1 | 4.7K | Resistor_SMD:R_2010_5025Metric_Pad1.52x2.65mm_HandSolder | R5 |
| 1 | 4.7K | Diode_SMD:D_2010_5025Metric_Pad1.52x2.65mm_HandSolder | R7 |
| 1 | 5vMount | PS2BaseMount:MountPoint | U23 |
| 1 | Audio_Left | PS2BaseMount:JST_1.5_2Pin | U3 |
| 1 | Audio_Right | PS2BaseMount:JST_1.5_2Pin | U4 |
| 1 | BATT_IN | PS2BaseMount:MountPoint | U22 |
| 1 | BATT_LED_A | LED_THT:LED_D3.0mm | D6 |
| 1 | BATT_LED_B | LED_THT:LED_D3.0mm | D7 |
| 1 | C470u | Capacitor_THT:CP_Radial_D8.0mm_P2.50mm | C8 |
| 1 | CP_220uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C10 |
| 1 | CP_680uF | Capacitor_THT:CP_Radial_D8.0mm_P2.50mm | C7 |
| 1 | DB15_Female_HighDensity | PS2BaseMount:ScreenBoardArea | J6 |
| 1 | DIODE | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | D1 |
| 1 | DPAD | PS2BaseMount:DPad_Buttons | U13 |
| 1 | DS18B20 | Package_TO_SOT_THT:TO-92_Inline | U6 |
| 1 | D_Schottky | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | D5 |
| 1 | Fan | PS2BaseMount:JST_1.5_2Pin | M7 |
| 1 | GND_IN | PS2BaseMount:MountPoint | U21 |
| 1 | INDUCTOR_33uH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | INTERACTION | PS2BaseMount:SMT_2X4X3.5MM | SW1 |
| 1 | LED_GREEN | LED_THT:LED_D3.0mm | D2 |
| 1 | LED_RED | LED_THT:LED_D3.0mm | D4 |
| 1 | LED_YELLOW | LED_THT:LED_D3.0mm | D3 |
| 1 | LM2596T-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U20 |
| 1 | LOGO | Logos:ColossusLogo2 | G*** |
| 1 | LOGO | Logos:BitBuiltLogo | G*** |
| 1 | OrangePiZero | PS2BaseMount:OrangePiZero | U1 |
| 1 | PAM8403 | w_smd_dil:so-16 | U5 |
| 1 | PIC16F18876-I_PT | PS2BaseMount:PIC16F18876-I_PT | U8 |
| 1 | PIC_14 | Package_DIP:DIP-14_W7.62mm_LongPads | U18 |
| 1 | PJ30240 | PS2BaseMount:AudioJack_PJ30240 | U2 |
| 1 | PS2AVPort | PS2BaseMount:PS2_AVPort_Complete | M2 |
| 1 | PS2AVPort_SideMount | PS2BaseMount:PS2_AVPort_Complete_MountSilk | M1 |
| 1 | PS2_MemCardMount | PS2BaseMount:PS2_MemCardMountPoints | P1 |
| 1 | PS2_RESET | PS2BaseMount:GND | U19 |
| 1 | Q_NMOS_GDS | Package_TO_SOT_THT:TO-220F-3_Vertical | Q2 |
| 1 | RJ14K | PS2BaseMount:RJ14K_Modified | U10 |
| 1 | RumbleA | PS2BaseMount:JST_1.5_2Pin | U14 |
| 1 | RumbleB | PS2BaseMount:JST_1.5_2Pin | U15 |
| 1 | SELECT | PS2BaseMount:SquishyTact | SW3 |
| 1 | START | PS2BaseMount:SquishyTact | SW2 |
| 1 | ScreenPWM | PS2BaseMount:JST_1.5_2Pin | U17 |
| 1 | TRIGGERS_LFT | PS2BaseMount:JST_1.25_3Pin | M5 |
| 1 | TRIGGERS_RIGHT | PS2BaseMount:JST_1.25_3Pin | M6 |
| 1 | TS_LFT | PS2BaseMount:JST_1.25_5Pin | M3 |
| 1 | TS_RHT | PS2BaseMount:JST_1.25_5Pin | M4 |
| 1 | USB_B | PS2BaseMount:USB_A_Custom_Throughhole_MountGuide | J4 |
| 1 | XOST_Buttons | PS2BaseMount:XOST_ButtonsV2 | U9 |
The 88 most common of 98 parts.
More from MRKane05/PS2BaseMount
3- 2 layers
PS2Board PreController
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
26 parts - 2 layers
PreControlChip
MRKane05/PS2BaseMount
The KiCad project for the base mount for the "Junkstation" PS2 portable project
19 parts
Similar boards
- 2 layers100 × 100 mm
Ft150ts B
z-XOF-z/FT150TS
Tablero digital + launcher para Android que funciona solo con el teléfono del manubrio y está listo para una tarjeta ESP32 en la moto.
127 parts - 2 layers46 × 183.2 mm
Dmx to pwm
TDSOJohn/Lasers
This repo contains the schematics and software for the monochrome laser bars used by VirtualConcrete.
68 parts1 - 2 layers33.7 × 97.8 mm
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 2 layers130 × 80 mm
Kegmon2 4scales
mp-se/pcb-designs
This repository contains the PCB designs for my projects and currently the following is included:
18 parts3 - 2 layers65 × 55 mm
- 2 layers47 × 48.3 mm
Olimex esp32-poe iso breakout
DanNixon/CAD-Things
Various things I have designed for CNC manufacture
27 parts - 2 layers50 × 50 mm
- 2 layers57 × 97 mm
MainCollar
plyalex/OpenFence
OpenFence is an open source GPS based digital livestock fencing system and web interface, aiming to reduce barriers of using cell grazing.
78 parts28GPL-3.0
Questions
How big is the PS2BaseMount PCB?
It measures 273 × 146 mm and has 2 copper layers, 1.6 mm thick.
What parts does the PS2BaseMount use?
98 parts, built around the DS18B20, LM2596T-5.0, PAM8403 and RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PS2BaseMount KiCad files?
From the MRKane05/PS2BaseMount repository on GitHub, at the commit this page was made from: the board is PS2BaseMount.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PS2BaseMount design in my own project?
Its repository states no licence, so its author keeps all rights: ask MRKane05 before reusing the design.