Skip to the content
2 layers46 × 24.2 mmLi Po Battery Charger, the printed circuit board in 3D

USB-C 1S Li-Po Power Management & 3.3 V Supply PCB

Size
46 × 24.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
38
Nets
36
Pads
123
Tracks, vias
324, 50
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
28 Sep 2026
Updated
1 Oct 2026

Overview

Li Po Battery Charger is an open-source printed circuit board by Hossam-Mamdouh, from the Hossam-Mamdouh/Li-Po_Battery_Charger repository on GitHub, published under the MIT licence. It is a 2-layer board of 46 × 24.2 mm with 38 parts on 36 nets, routed with 324 tracks and 50 vias.

It is built around the TPS63802DLAR, DW01A and MCP73871-2CCI/ML, with the S2B-PH-K-S(LF)(SN), ESD9B5V and PSC-1608U52GC-G4 among its other parts. Its parts include 14 resistors, 8 capacitors, 3 ICs, 3 diodes and 1 transistor. It belongs with the power boards of this library.

Main components

6

README

README.md

PowerCore 3V3

USB-C 1S Li-Po Power Management & 3.3 V Supply PCB

PowerCore 3V3 is a compact power-management board for a single-cell Li-Po battery. It combines USB-C input, Li-Po charging, system power-path management, battery protection, and a regulated 3.3 V output.

Features

USB-C 5 V power input

1S Li-Po battery support

MCP73871 charger with system power-path management

DW01A + FS8205A battery protection

TPS63802 buck-boost regulator

Regulated 3.3 V output

Designed for up to 500 mA system load

Approximately 500 mA maximum programmed charge current

USB input PTC protection

Charge/status indication LEDs

Power Architecture

USB-C 5 V | v Input Protection | v MCP73871 Charger + Power Path | | v v 1S Li-Po VSYS | | v v DW01A + FS8205A TPS63802 Battery Protection Buck-Boost | v 3.3 V | v System Load

Main Components

Reference Component Function

U2 MCP73871 Li-Po charger and power-path controller U3 DW01A Battery protection controller Q1 FS8205A Dual N-channel MOSFET protection switch U4 TPS63802 Buck-boost regulator F1 1.5 A PTC USB input over-current protection J1 USB-C 5 V power input Battery JST-PH 2-pin 1S Li-Po connection

Charger Configuration

Charge Current

PROG1 = 2 kΩ

Programs approximately 500 mA maximum charge current.

The actual charging current is reduced when system load consumes part of the available input power.

Termination Current

PROG3 = 20 kΩ

Sets approximately 50 mA termination current.

Input Current Mode

SEL = +5V_USB

The charger uses the higher-current adapter mode rather than the 500 mA USB mode.

Other Settings

CE pulled high → charging enabled

TE# tied to GND → safety timer enabled

THERM uses a fixed 10 kΩ resistor to GND

VPCC tied to +5V_USB

PROG2 pulled high through 10 kΩ

PG# pulled high through 10 kΩ

STAT1 / STAT2 provide status indication

Battery Protection

The protection stage uses a DW01A controller and FS8205A dual MOSFET.

For the selected FUXINSEMI FS8205A:

Pin 1 → S1 Pin 2 → D1/D2 Pin 3 → S2 Pin 4 → G2 Pin 5 → D1/D2 Pin 6 → G1

Pins 2 and 5 are the common drain connection and must be electrically connected.

External connections:

Q1 S1 → B- Q1 S2 → GND / P- Q1 G1 → DW01A OD Q1 G2 → DW01A OC Q1 D1/D2 → common drain node

DW01A current sense:

CSI → 1 kΩ → GND / P-

3.3 V Regulation

The TPS63802 maintains a regulated 3.3 V rail from the 1S battery/system rail.

Intended load: 500 mA

Inductor: 0.47 µH

Input capacitor: 10 µF

Output capacitor: 22 µF

Feedback: 511 kΩ / 91 kΩ

EN: VSYS

MODE: GND

The buck-boost topology allows 3.3 V regulation as battery voltage moves above and below the output voltage.

USB-C Interface

The USB-C connector is configured as a power input.

CC1 → 5.1 kΩ → GND CC2 → 5.1 kΩ → GND

Input decoupling and transient protection are included.

Battery Connector

The current schematic uses:

Battery Pin 2 → VBAT (+) Battery Pin 1 → B- (-)

JST-PH pin numbering does not inherently define battery polarity. Verify the actual battery cable/mating connector pinout before connection.

Clearly mark + and − on the PCB.

Power Budget

The intended system load is:

3.3 V × 500 mA = 1.65 W

The programmed 500 mA battery charge current is a maximum. Actual charge current depends on system load, USB supply capability, regulator efficiency, and charger operating conditions.

PCB Layout Guidelines

Keep TPS63802 input/output capacitors close to the IC.

Keep the 0.47 µH inductor close to the switching pins.

Keep the FB trace away from switching nodes.

Use short, low-impedance high-current paths.

Place USB input protection close to the USB-C connector.

Use appropriate copper width for battery and system power paths.

Provide solid ground copper and thermal areas.

Clearly mark battery polarity.

Design Status

Revision: A Status: Prototype / Engineering Design

Before manufacturing, verify:

Schematic ERC

PCB DRC

Q1 symbol-to-footprint pin mapping

Battery connector pinout

PTC fuse rating and thermal derating

USB-C input capability

TPS63802 thermal performance

Charger behavior under simultaneous load and charging

Battery protection thresholds

Applications

Embedded systems

IoT devices

Portable electronics

Battery-powered sensors

ESP32-based products

Automation systems

Custom electronics prototypes

Tools

KiCad 10.x

LCSC components where applicable

Author

Hossam Mamdouh Embedded Systems Engineer

Portfolio: https://hossam-mamdouh.github.io/

License

Choose an appropriate hardware/software license before public release.

Parts

38
QtyValueFootprintReferences
510uFlcsc_footprints:C3039641_C0603C1, C3, C6, C7, C8
4, , ,
410kΩlcsc_footprints:C326912_R0402R10, R12, R13, R14
31KΩlcsc_footprints:C11702_R0402R6, R7, R11
25.1KΩlcsc_footprints:C25905_R0402R1, R2
2S2B-PH-K-S(LF)(SN)lcsc_footprints:C173752_CONN-TH_S2B-PH-K-S-LF-SNBattery, Load
10.47 µHlcsc_footprints:C285747_IND-SMD_L4_0-W4_0_CHILISIN_MHCI04012NL1
10603lcsc_footprints:C2286_LED-SMD_L1_6-W0_8-R-RDLED1
11.5Alcsc_footprints:C118413_F1206F1
1100nFlcsc_footprints:C5448791_C0402C2
1100nFlcsc_footprints:C5137616_C0603C5
1100Ωlcsc_footprints:C106232_R0402R9
120 kΩlcsc_footprints:C93942_R0402R8
122uFlcsc_footprints:C22367828_C0603C4
12KΩlcsc_footprints:C4109_R0402R5
1511kΩlcsc_footprints:C861454_R0603R3
191 kΩlcsc_footprints:C2907077_R0603R4
1DW01Alcsc_footprints:C42459937_SOT-23-6_L2_9-W1_6-P0_95-LS2_8-BLU3
1ESD9B5Vlcsc_footprints:C2905646_SOD-923_L0_8-W0_6-LS1_0-BI-1D1
1FS8205A_C908265lcsc_footprints:C908265_SOT-23-6_L2_9-W1_6-P0_95-LS2_8-BRQ1
1MCP73871-2CCI/MLlcsc_footprints:C5121473_QFN-20_L4_0-W4_0-P0_50-BL-EP2_7U2
1PSC-1608U52GC-G4lcsc_footprints:C22371297_LED0603-RD_GREENLED2
1TPS63802DLARlcsc_footprints:C2845237_VSON-10_L3_0-W2_0-P0_50-TLU1
1TYPE-C 16P(073)lcsc_footprints:C668624_USB-C-SMD_TYPE-C16PIN_C668624USB-C

Similar boards

  • 2 layers28 × 28 mmScoopy, the printed circuit board in 3D

    Scoopy

    NiceHatThanks/scoopy-node

    Tiny, local-first room hardware for Home Assistant and ESPHome.

    13 parts41
  • 4 layers100 × 80 mmBuilt, the printed circuit board in 3D

    Built

    devbisme/ai-circuit-design-tests

    Tests of KiCad-related AI tools.

    243 parts10
  • 4 layers125 × 70 mm1000base t1-converter, the printed circuit board in 3D

    1000base t1-converter

    TLDSJPWORK/1000base-t1-converter

    学習用 1000BASE-T1 ↔ 1000BASE-T メディアコンバーター

    184 partsCC-BY-4.0
  • 4 layers118 × 76 mmSmart led badge, the printed circuit board in 3D

    Smart led badge

    zgeez/Pixel-Badge

    Wearable 32x32 LED badge with Zephyr firmware, BLE control, passive NFC, and a Flutter Android app, built around a custom nRF52840 PCB.

    1,236 partsMIT
  • 2 layers60 × 111.3 mmSilkscreen pcb, the printed circuit board in 3D

    Silkscreen pcb

    iandchasse/silkscreen-pcb

    Silkscreen: open-hardware ESP32-S3 e-paper reader mainboard (KiCad 9). Formerly the de-link hub.

    189 parts589CERN-OHL-S-2.0
  • 2 layers50.2 × 95.2 mmCheetoPet, the printed circuit board in 3D

    CheetoPet

    Cheet0sDelet0s/cheetoPet

    an esp32 s3 based tamagotchi

    104 parts3GPL-2.0
  • 4 layers42.5 × 47 mmTamagotchi thing, the printed circuit board in 3D

    Tamagotchi thing

    afonsus1997/Tamagotchi-thing

    Just a dumb attempt to make a tamagotch.

    90 parts
  • 2 layers30 × 60 mmSensor node kicad, the printed circuit board in 3D

    Sensor node kicad

    shyver/sensor-node

    This project is a compact, battery-powered environmental monitoring device built around the ESP32. It is designed to measure temperature, humidity, and atmospheric pressure, and transmit data wirelessly over Wi-Fi.

    53 partsMIT

Questions

How big is the Li Po Battery Charger PCB?

It measures 46 × 24.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Li Po Battery Charger use?

38 parts, built around the TPS63802DLAR, DW01A, MCP73871-2CCI/ML and S2B-PH-K-S(LF)(SN). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Li Po Battery Charger KiCad files?

From the Hossam-Mamdouh/Li-Po_Battery_Charger repository on GitHub, at the commit this page was made from: the board is Li-Po_Battery_Charger.kicad_pcb and its schematic Li-Po_Battery_Charger.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Li Po Battery Charger design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).