Skip to the content
21

MCP73871-2CCI/ML

Microchip TechnologyExtended

-40℃~+85℃ 1 1.1A 28uA 4.1V~6V 4.2V Charging IC Support Support QFN-20(4x4) Battery Management ROHS

Part id
microchip/MCP73871-2CCI/ML
Category
Battery Management
Package
QFN-20(4x4)
Pins
21
In stock
395 at JLCPCB (C5121473)
Used on
28 open-source boards

Overview

The MCP73871-2CCI/ML is a battery Management made by Microchip Technology in a QFN-20(4x4) package with 21 pins. -40℃~+85℃ 1 1.1A 28uA 4.1V~6V 4.2V Charging IC Support Support QFN-20(4x4) Battery Management ROHS.

PCBKit's library has its KiCad symbol (Battery_Management:MCP73871, from KiCad's library) and its footprint (Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm, from KiCad's library), ready for a KiCad board. 395 are in stock at JLCPCB (part C5121473). 28 open-source boards in 27 repositories on GitHub use it.

Symbol

1OUT2VPCC3SEL4PROG25THERM6PG7STAT28STAT1/LBO9TE10VSS12PROG313PROG114VBAT16VBAT_SENSE17CE18IN
Battery_Management:MCP73871From KiCad's library

Footprint

21
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mmFrom KiCad's library

From the datasheet

16
Supply, most
6 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
7 V · VIN, absolute maximum · p. 4
Takes working
2.5 mA · ISS, typical while charging · p. 4
Takes at most
3.75 mA · ISS, max while charging · p. 4
Takes asleep
180 µA · ISS, typical standby · p. 4
Takes asleep
28 µA · ISS, typical shutdown · p. 4
Gives
1 A · Battery fast charge current, rated maximum · p. 1
Current limit
1.65 A · AC-DC adapter input current limit, typical; SEL = High · p. 5
Current limit
90 mA · USB input current limit, typical; PROG2 = Low, SEL = Low · p. 5
Current limit
450 mA · USB input current limit, typical; PROG2 = High, SEL = Low · p. 5
A pin gives at most
35 mA · STAT1/LBO, STAT2 and PG sink current, max · p. 6
Works from
-40 °C · TA, specified ambient minimum · p. 8
Works up to
85 °C · TA, specified ambient maximum · p. 8
Junction, hottest
125 °C · TJ, operating maximum · p. 8
Junction to air (20LD-QFN, 4x4)
50 K/W · Typical; 4-Layer JC51-7 Standard Board, natural convection · p. 8
Junction to case (20LD-QFN, 4x4)
8 K/W · Junction to case, typical · p. 8

What it is and has

13
System load sharing
Integrated system load sharing and battery charge management · p. 1
Charge controller
Linear · p. 1
Pass transistors
Integrated · p. 1
Current sense
Integrated · p. 1
Protection
Integrated reverse discharge protection · p. 1
Total input current control
Maximum 1.8A · p. 1
Charge termination
Resistor programmable termination set point · p. 1
Recharge
Automatic · p. 1
Safety timer
Enable/disable control · p. 1
Battery temperature
Battery cell temperature monitor · p. 1
Protection
Undervoltage lockout · p. 1
Status indicators
Charge status and fault condition indicators · p. 1
Package
20-Lead QFN (4 mm x 4 mm) · p. 1

Specifications

76
ParameterConditionsAs printedPage
VIN VINmax 7 V4
Storage temperaturemin -65 · max 150 °C4
Machine ModelESD protection on all pins; 200 pF, No Series Resistancemax 300 V4
Supply Voltage VINMinimum VREG + 0.3Vmax 6 V4
Supply Current ISSChargingtyp 2500 · max 3750 uA4
Supply Current ISSCharge Completetyp 260 · max 350 uA4
Supply Current ISSStandbytyp 180 · max 300 uA4
Supply Current ISSShutdown (VDD < VBAT – 100 mV or VDD < VSTOP)typ 28 · max 50 uA4
UVLO Hysteresis VHYStyp 90 mV4
Regulated Charge Voltage Tolerance VRTOLTA = +25°Cmin -0.5 · max 0.5 %4
Regulated Charge Voltage Tolerance VRTOLTA = -5°C to +55°Cmin -0.75 · max 0.75 %4
Line Regulation |(ΔVBAT/VBAT)/ΔVDD|VDD = [VREG(typical) + 1V] to 6V; IOUT = 10 mAtyp 0.08 · max 0.2 %/V4
Load Regulation |ΔVBAT/VBAT|IOUT = 10 mA to 150 mA; VDD = [VREG(typical) + 1V]typ 0.08 · max 0.18 %4
Supply Ripple Attenuation PSRRIOUT = 10 mA, 1 kHztyp -47 dB4
Supply Ripple Attenuation PSRRIOUT = 10 mA, 10 kHztyp -40 dB4
AC-Adapter Fast Charge Current IREGPROG1 = 10 kΩ; TA = -5°C to +55°C, SEL = Highmin 90 · typ 100 · max 110 mA5
AC-Adapter Fast Charge Current IREGPROG1 = 1 kΩ; TA = -5°C to +55°C, SEL = Highmin 900 · typ 1000 · max 1100 mA5
USB Fast Charge Current IREGPROG2 = Low, SEL = Low; TA = -5°C to +55°C; maximum available charge current also limited by PROG1min 80 · typ 90 · max 100 mA5
USB Fast Charge Current IREGPROG2 = High, SEL = Low; TA = -5°C to +55°C; maximum available charge current also limited by PROG1min 400 · typ 450 · max 500 mA5
USB-Port Supply Current Limit ILIMIT_USBPROG2 = Low, SEL = Low; TA = -5°C to +55°Cmin 80 · typ 90 · max 100 mA5
USB-Port Supply Current Limit ILIMIT_USBPROG2 = High, SEL = Low; TA = -5°C to +55°Cmin 400 · typ 450 · max 500 mA5
AC-DC Adapter Current Limit ILIMIT_ACSEL = High, TA = -5°C to +55°Cmin 1500 · typ 1650 · max 1800 mA5
VPCC Input Threshold VVPCCIOUT = 10 mA; TA = -5°C to +55°Ctyp 1.23 V5
VPCC Input Threshold Tolerance VRTOLmin -3 · max 3 %5
Input Leakage Current ILKVPCC; VVPCC = VDDtyp 0.01 · max 1 uA5
Precondition Current Ratio IPREG/IREGPROG1 = 1.0 kΩ to 10 kΩ; TA = -5°C to +55°Cmin 7.5 · typ 10 · max 12.5 %5
Precondition Current Threshold Ratio VPTH/VREGVBAT Low-to-Highmin 69 · typ 72 · max 75 %5
Precondition Hysteresis VPHYSVBAT High-to-Lowtyp 105 mV5
Charge Termination Current Ratio ITERMPROG3 = 10 kΩ; TA = -5°C to +55°Cmin 75 · typ 100 · max 125 mA5
Charge Termination Current Ratio ITERMPROG3 = 100 kΩ; TA = -5°C to +55°Cmin 7.5 · typ 10 · max 12.5 mA5
ON-Resistance RDS_ONIN-to-OUT Pass Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m5
ON-Resistance RDSON_Charge Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m6
ON-Resistance RDS_ONBAT-to-OUT Pass Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m6
Output Reverse Leakage Current IDISCHARGEShutdown (VBAT < VDD < VUVLO)typ 30 · max 40 uA6
Output Reverse Leakage Current IDISCHARGEShutdown (0 < VDD < VBAT)typ 30 · max 40 uA6
Output Reverse Leakage Current IDISCHARGEVBAT = Power Out, No Loadtyp 30 · max 40 uA6
Output Reverse Leakage Current IDISCHARGECharge Completetyp -6 · max -13 uA6
Sink Current ISINKStatus Indicators - STAT1 (LBO), STAT2, PGtyp 16 · max 35 mA6
Low Output Voltage VOLStatus Indicators - STAT1 (LBO), STAT2, PG; ISINK = 4 mAtyp 0.4 · max 1 V6
Input Leakage Current ILKStatus Indicators - STAT1 (LBO), STAT2, PG; High Impedance, VDD on pintyp 0.01 · max 1 uA6
Low Battery Detection Hysteresis VLBO_HYSVBAT Low-to-Hightyp 150 mV6
Charge Impedance Range RPROGPROG1 Input (PROG1)min 1 · max 20 k6
Termination Impedance Range RPROGPROG3 Input (PROG3)min 5 · max 100 k6
Input High Voltage Level VIHPROG2 Input (PROG2)min 1.8 V6
Input Low Voltage Level VILPROG2 Input (PROG2)max 0.8 V6
Input Leakage Current ILKPROG2 Input (PROG2); VPROG2 = VDDtyp 0.01 · max 1 uA6
Input High Voltage Level VIHTimer Enable (TE); ensured by design and not production testedmin 1.8 V6
Input Low Voltage Level VILTimer Enable (TE); ensured by design and not production testedmax 0.8 V6
Input Leakage Current ILKTimer Enable (TE); VTE = VDDtyp 0.01 · max 1 uA6
Input High Voltage Level VIHChip Enable (CE)min 1.8 V7
Input Low Voltage Level VILChip Enable (CE)max 0.8 V7
Input Leakage Current ILKChip Enable (CE); VCE = VDDtyp 0.01 · max 1 uA7
Input High Voltage Level VIHInput Source Selection (SEL)min 1.8 V7
Input Low Voltage Level VILInput Source Selection (SEL)max 0.8 V7
Input Leakage Current ILKInput Source Selection (SEL); VSEL = VDDtyp 0.01 · max 1 uA7
Thermistor Current Source ITHERM2 kΩ < RTHERM < 50 kΩmin 47 · typ 50 · max 53 uA7
Upper Trip Threshold VT1Thermistor Comparator; VT1 Low-to-Highmin 1.2 · typ 1.24 · max 1.26 V7
Upper Trip Point Hysteresis VT1HYSThermistor Comparatortyp -40 mV7
Lower Trip Threshold VT2Thermistor Comparator; VT2 High-to-Lowmin 0.23 · typ 0.25 · max 0.27 V7
Lower Trip Point Hysteresis VT2HYSThermistor Comparatortyp 40 mV7
Die Temperature TSDThermal Shutdowntyp 150 C7
Die Temperature Hysteresis TSDHYSThermal Shutdowntyp 10 C7
UVLO Start Delay tSTARTVDD Low-to-Highmax 5 ms8
Transition Time Out of Precondition tDELAYVBAT < VPTH to VBAT > VPTHmax 10 ms8
Current Rise Time Out of Precondition tRISEIOUT Rising to 90% of IREGmax 10 ms8
Precondition Comparator Filter Time tPRECONAverage VBAT Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms8
Termination Comparator Filter Time tTERMAverage IOUT Fallingmin 0.4 · typ 1.3 · max 3.2 ms8
Charge Comparator Filter Time tCHARGEAverage VBAT Fallingmin 0.4 · typ 1.3 · max 3.2 ms8
Thermistor Comparator Filter Time tTHERMAverage THERM Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms8
Status Output Turn-off tOFFISINK = 1 mA to 0 mAmax 500 us8
Status Output Turn-on tONISINK = 0 mA to 1 mAmax 500 us8
Specified Temperature Range TAmin -40 · max 85 °C8
Operating Temperature Range TJmin -40 · max 125 °C8
Storage Temperature Range TAmin -65 · max 150 °C8
Thermal Resistance, 20LD-QFN, 4x4 JA4-Layer JC51-7 Standard Board, Natural Convectiontyp 50 °C/W8
Thermal Resistance, 20LD-QFN, 4x4 JCtyp 8 °C/W8

Open-source boards using it

28See all 28
  • 2 layers75 × 40 mmPicoTop Board Rev2, the printed circuit board in 3D

    PicoTop Board Rev2

    7west/PicoTop

    A very basic computer & OS based on the RP2350 microcontroller

    86 parts66
  • 2 layers160 × 100 mm36C3 Badge Hardware, the printed circuit board in 3D

    36C3 Badge Hardware

    CatoLynx/36C3-Badge

    VFD and LED badge fitting the 36C3 design

    159 parts5GPL-3.0
  • 2 layers150 × 150 mmBoardGame, the printed circuit board in 3D

    BoardGame

    jkordek1/Man-Don-t-Get-Angry-Board-game

    "Man don't get mad" - electronic board game

    218 parts5
  • 2 layers50 × 70 mmTime2time, the printed circuit board in 3D

    Time2time

    Resaj/time2time

    Chronometer with partials measurement for the line-following competitions

    97 parts5
  • 4 layers60 × 33.5 mmHome weather station esp32, the printed circuit board in 3D

    Home weather station esp32

    Norbixix/home-weather-station-esp32

    ESP32-based low-power home weather station PCB project

    49 parts2
  • 4 layers210 × 100 mm02 Power Board, the printed circuit board in 3D

    02 Power Board

    ad4363/LuX-ray-PCBs

    A repository containing KiCad schematic and pcb files for a wireless radiation detector testing interface

    115 parts1
  • 2 layers158.3 × 110 mmLathrum thesis, the printed circuit board in 3D

    Lathrum thesis

    Dylancyclone/thesis

    Undergraduate Honors thesis for graduation in 2022

    80 parts1
  • 4 layers53.4 × 38.4 mmGSR Board, the printed circuit board in 3D

    GSR Board

    esl-epfl/GSR_monitor

    Discrete validation platform for the HEEPidermis low-power SoC, designed for low-noise Galvanic Skin Response (GSR) measurements

    159 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP73871-2CCI/ML?

Yes. The symbol is Battery_Management:MCP73871 and the footprint Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP73871-2CCI/ML?

QFN-20(4x4), with 21 pins. Its footprint is drawn on this page.

Where is the MCP73871-2CCI/ML datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP73871-2CCI/ML?

JLCPCB lists it as part C5121473, with 395 in stock; the sellers' links on this page open their listings.

What can replace the MCP73871-2CCI/ML?

Parts like it in the library: the MCP73871T-2CCI/ML by Microchip Technology, the MCP73871-2CAI/ML by Microchip Technology, the MCP73871-2AAI/ML by Microchip Technology and the ADP5063ACPZ-1-R7 by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP73871-2CCI/ML?

28 boards in 27 repositories on GitHub; the most starred are listed on this page, with their KiCad files.