Skip to the content
21

MCP73871T-2CCI/ML

Microchip TechnologyExtended

-40℃~+85℃ 1 1.8A 28uA 4.2V 4.6V~6V Charging IC Support QFN-20-EP(4x4) Battery Management ROHS

Part id
microchip/MCP73871T-2CCI/ML
Category
Battery Management
Package
QFN-20-EP(4x4)
Pins
20
In stock
1,038 at JLCPCB (C511310)
Used on
2 open-source boards

Overview

The MCP73871T-2CCI/ML is a battery Management made by Microchip Technology in a QFN-20-EP(4x4) package with 21 pins. -40℃~+85℃ 1 1.8A 28uA 4.2V 4.6V~6V Charging IC Support QFN-20-EP(4x4) Battery Management ROHS.

PCBKit's library has its KiCad symbol (Battery_Management:MCP73871, from KiCad's library) and its footprint (Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm, from KiCad's library), ready for a KiCad board. 1,038 are in stock at JLCPCB (part C511310). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1OUT2VPCC3SEL4PROG25THERM6PG7STAT28STAT1/LBO9TE10VSS12PROG313PROG114VBAT16VBAT_SENSE17CE18IN
Battery_Management:MCP73871From KiCad's library

Footprint

21
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mmFrom KiCad's library

From the datasheet

16
Supply, most
6 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
7 V · VIN, absolute maximum · p. 5
Works from
-40 °C · TA, specified ambient min · p. 9
Works up to
85 °C · TA, specified ambient max · p. 9
Junction, hottest
125 °C · TJ, operating max · p. 9
Takes working
2.5 mA · ISS, charging typical · p. 5
Takes at most
3.75 mA · ISS, charging max · p. 5
Takes asleep
180 µA · ISS, standby typical · p. 5
Takes asleep
28 µA · ISS, shutdown typical · p. 5
Gives
1 A · Battery fast charge, PROG1 = 1 kΩ, SEL high, typical · p. 6
Current limit
1.65 A · AC-DC adapter total input limit, SEL high, typical · p. 6
Current limit
90 mA · USB input limit, PROG2 low, SEL low, typical · p. 6
Current limit
450 mA · USB input limit, PROG2 high, SEL low, typical · p. 6
Output
4.2 V · VREG, regulated battery charge voltage typical · p. 5
Junction to air (20LD-QFN, 4x4)
50 K/W · Junction to ambient typical, 4-layer JC51-7 board, natural convection · p. 9
Junction to case (20LD-QFN, 4x4)
8 K/W · Junction to case typical · p. 9

What it is and has

16
System load sharing
Integrated system load sharing and battery charge management · p. 1
Power path
Ideal diode operation · p. 1
Charge controller
Linear · p. 1
Pass transistors
Integrated · p. 1
Current sense
Integrated · p. 1
Protection
Integrated reverse discharge protection · p. 1
Charge voltage regulation tolerance
±0.5% · p. 1
Total input current control
Maximum 1.8A · p. 1
Recharge
Automatic · p. 1
End-of-charge control
Automatic · p. 1
Safety timer
Enable/disable control · p. 1
Preconditioning
0.1C for deeply depleted cells · p. 1
Battery temperature monitor
Battery cell temperature monitoring · p. 1
Protection
Undervoltage lockout · p. 1
Indicators
Charge status and fault condition · p. 1
Package
20-Lead QFN (4 mm x 4 mm) · p. 1

Around it

5
cap 4.7 μF
between OUT and VSS; Minimum recommended bypass capacitance. · p. 17
cap 4.7 μF
between VBAT and VSS; Minimum bypass capacitance to ensure loop stability when the battery is disconnected. · p. 18
res 330 k
between IN and VPCC; R1 in the VPCC voltage-divider example. · p. 18
res 110 k
between VPCC and VSS; R2 in the VPCC voltage-divider example. · p. 18
res 5 k to 100 k
between PROG3 and VSS; Recommended termination programming resistor range. · p. 23

Specifications

79
ParameterConditionsAs printedPage
VIN VINmax 7 V5
All Inputs and Outputs w.r.t.VSSVDD = VIN or VBAT; upper limit VDD+0.3Vmin -0.3 V5
Storage temperaturemin -65 · max 150 °C5
ESD protection on all pinsHuman Body Model (1.5 kΩ in Series with 100 pF)min 4 kV5
ESD protection on all pinsMachine Model (200 pF, No Series Resistance)max 300 V5
Supply Voltage VINMinimum is VREG + 0.3Vmax 6 V5
Supply Current ISSChargingtyp 2500 · max 3750 uA5
Supply Current ISSCharge Completetyp 260 · max 350 uA5
Supply Current ISSStandbytyp 180 · max 300 uA5
Supply Current ISSShutdown; VDD < VBAT – 100 mV or VDD < VSTOPtyp 28 · max 50 uA5
UVLO Hysteresis VHYStyp 90 mV5
Regulated Charge Voltage VREGMCP73871T-2CCI/ML; VDD = [VREG(typical) + 1V], IOUT = 10 mA, TA = -5°C to +55°Cmin 4.179 · typ 4.2 · max 4.221 V5
Regulated Charge Voltage Tolerance VRTOLTA = +25°Cmin -0.5 · max 0.5 %5
Regulated Charge Voltage Tolerance VRTOLTA = -5°C to +55°Cmin -0.75 · max 0.75 %5
Line Regulation |(ΔVBAT/VBAT)/ΔVDD|VDD = [VREG(typical) + 1V] to 6V; IOUT = 10 mAtyp 0.08 · max 0.2 %/V5
Load Regulation |ΔVBAT/VBAT|IOUT = 10 mA to 150 mA; VDD = [VREG(typical) + 1V]typ 0.08 · max 0.18 %5
Supply Ripple Attenuation PSRRIOUT = 10 mA, 1 kHztyp -47 dB5
Supply Ripple Attenuation PSRRIOUT = 10 mA, 10 kHztyp -40 dB5
AC-Adapter Fast Charge Current IREGPROG1 = 10 kΩ, TA = -5°C to +55°C, SEL = Highmin 90 · typ 100 · max 110 mA6
AC-Adapter Fast Charge Current IREGPROG1 = 1 kΩ, TA = -5°C to +55°C, SEL = Highmin 900 · typ 1000 · max 1100 mA6
USB Fast Charge Current IREGPROG2 = Low, SEL = Low, TA = -5°C to +55°C; maximum available charge current also limited by PROG1min 80 · typ 90 · max 100 mA6
USB Fast Charge Current IREGPROG2 = High, SEL = Low, TA = -5°C to +55°C; maximum available charge current also limited by PROG1min 400 · typ 450 · max 500 mA6
USB-Port Supply Current Limit ILIMIT_USBPROG2 = Low, SEL = Low, TA = -5°C to +55°Cmin 80 · typ 90 · max 100 mA6
USB-Port Supply Current Limit ILIMIT_USBPROG2 = High, SEL = Low, TA = -5°C to +55°Cmin 400 · typ 450 · max 500 mA6
AC-DC Adapter Current Limit ILIMIT_ACSEL = High, TA = -5°C to +55°Cmin 1500 · typ 1650 · max 1800 mA6
VPCC Input Threshold VVPCCIOUT = 10 mA, TA = -5°C to +55°Ctyp 1.23 V6
VPCC Input Threshold Tolerance VRTOLmin -3 · max 3 %6
Input Leakage Current ILKVPCC; VVPCC = VDDtyp 0.01 · max 1 uA6
Precondition Current Ratio IPREG/IREGPROG1 = 1.0 kΩ to 10 kΩ, TA = -5°C to +55°Cmin 7.5 · typ 10 · max 12.5 %6
Precondition Current Threshold Ratio VPTH/VREGVBAT Low-to-Highmin 69 · typ 72 · max 75 %6
Precondition Hysteresis VPHYSVBAT High-to-Lowtyp 105 mV6
Charge Termination Current Ratio ITERMPROG3 = 10 kΩ, TA = -5°C to +55°Cmin 75 · typ 100 · max 125 mA6
Charge Termination Current Ratio ITERMPROG3 = 100 kΩ, TA = -5°C to +55°Cmin 7.5 · typ 10 · max 12.5 mA6
ON-Resistance RDS_ONIN-to-OUT Pass Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m6
ON-Resistance RDSON_Charge Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m7
ON-Resistance RDS_ONBAT-to-OUT Pass Transistor; VDD = 4.5V, TJ = 105°Ctyp 200 m7
Output Reverse Leakage Current IDISCHARGEShutdown; VBAT < VDD < VUVLOtyp 30 · max 40 uA7
Output Reverse Leakage Current IDISCHARGEShutdown (0 < VDD < VBAT)typ 30 · max 40 uA7
Output Reverse Leakage Current IDISCHARGEVBAT = Power Out, No Loadtyp 30 · max 40 uA7
Output Reverse Leakage Current IDISCHARGECharge Completetyp -6 · max -13 uA7
Sink Current ISINKStatus Indicators - STAT1 (LBO), STAT2, PGtyp 16 · max 35 mA7
Low Output Voltage VOLStatus Indicators - STAT1 (LBO), STAT2, PG; ISINK = 4 mAtyp 0.4 · max 1 V7
Input Leakage Current ILKStatus Indicators - STAT1 (LBO), STAT2, PG; High Impedance, VDD on pintyp 0.01 · max 1 uA7
Low Battery Detection Hysteresis VLBO_HYSVBAT Low-to-Hightyp 150 mV7
Charge Impedance Range RPROGPROG1 Input (PROG1)min 1 · max 20 k7
Termination Impedance Range RPROGPROG3 Input (PROG3)min 5 · max 100 k7
Input High Voltage Level VIHPROG2 Input (PROG2)min 1.8 V7
Input Low Voltage Level VILPROG2 Input (PROG2)max 0.8 V7
Input Leakage Current ILKPROG2 Input (PROG2); VPROG2 = VDDtyp 0.01 · max 1 uA7
Input High Voltage Level VIHTimer Enable (TE); ensured by design and not production testedmin 1.8 V7
Input Low Voltage Level VILTimer Enable (TE); ensured by design and not production testedmax 0.8 V7
Input Leakage Current ILKTimer Enable (TE); VTE = VDDtyp 0.01 · max 1 uA7
Input High Voltage Level VIHChip Enable (CE)min 1.8 V8
Input Low Voltage Level VILChip Enable (CE)max 0.8 V8
Input Leakage Current ILKChip Enable (CE); VCE = VDDtyp 0.01 · max 1 uA8
Input High Voltage Level VIHInput Source Selection (SEL)min 1.8 V8
Input Low Voltage Level VILInput Source Selection (SEL)max 0.8 V8
Input Leakage Current ILKInput Source Selection (SEL); VSEL = VDDtyp 0.01 · max 1 uA8
Thermistor Current Source ITHERM2 kΩ < RTHERM < 50 kΩmin 47 · typ 50 · max 53 uA8
Upper Trip Threshold VT1Thermistor Comparator; VT1 Low-to-Highmin 1.2 · typ 1.24 · max 1.26 V8
Upper Trip Point Hysteresis VT1HYSThermistor Comparatortyp -40 mV8
Lower Trip Threshold VT2Thermistor Comparator; VT2 High-to-Lowmin 0.23 · typ 0.25 · max 0.27 V8
Lower Trip Point Hysteresis VT2HYSThermistor Comparatortyp 40 mV8
Die Temperature TSDThermal Shutdowntyp 150 C8
Die Temperature Hysteresis TSDHYSThermal Shutdowntyp 10 C8
UVLO Start Delay tSTARTVDD Low-to-Highmax 5 ms9
Transition Time Out of Precondition tDELAYVBAT < VPTH to VBAT > VPTHmax 10 ms9
Current Rise Time Out of Precondition tRISEIOUT Rising to 90% of IREGmax 10 ms9
Precondition Comparator Filter Time tPRECONAverage VBAT Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms9
Termination Comparator Filter Time tTERMAverage IOUT Fallingmin 0.4 · typ 1.3 · max 3.2 ms9
Charge Comparator Filter Time tCHARGEAverage VBAT Fallingmin 0.4 · typ 1.3 · max 3.2 ms9
Thermistor Comparator Filter Time tTHERMAverage THERM Rise/Fallmin 0.4 · typ 1.3 · max 3.2 ms9
Status Output Turn-off tOFFISINK = 1 mA to 0 mAmax 500 us9
Status Output Turn-on tONISINK = 0 mA to 1 mAmax 500 us9
Specified Temperature Range TAmin -40 · max 85 °C9
Operating Temperature Range TJmin -40 · max 125 °C9
Storage Temperature Range TAmin -65 · max 150 °C9
Thermal Resistance, 20LD-QFN, 4x4 JA4-Layer JC51-7 Standard Board, Natural Convectiontyp 50 °C/W9
Thermal Resistance, 20LD-QFN, 4x4 JCtyp 8 °C/W9

Pins, by the datasheet

21
1 OUT
System Output Terminal. · p. 17
2 VPCC
Voltage proportional charge control. · p. 17
3 SEL
Input type selection: low for USB port, high for AC-DC adapter. · p. 17
4 PROG2
USB port input current limit selection when SEL is low: low selects 100 mA, high selects 500 mA. · p. 17
5 THERM
Thermistor monitoring input and bias current. · p. 17
6 PG
Power Good Status Output. · p. 17
7 STAT2
Charge Status Output 2. · p. 17
8 STAT1/LBO
Charge Status Output 1; low battery output indicator when VBAT > VIN. · p. 17
9 TE
Enables Safety Timer when active-low. · p. 17
10 VSS
Battery Management 0V Reference. · p. 17
11 VSS
Battery Management 0V Reference. · p. 17
12 PROG3
Termination set point for both AC-DC adapter and USB port. · p. 17
13 PROG1
Fast charge current regulation setting with SEL high; preconditioning set point for both USB port and AC-DC adapter. · p. 17
14 VBAT
Battery Positive Input and Output connection. · p. 17
15 VBAT
Battery Positive Input and Output connection. · p. 17
16 VBAT_SENSE
Battery Voltage Sense. · p. 17
17 CE
Device Charge Enable; enabled when CE is high. · p. 17
18 IN
Power Supply Input. · p. 17
19 IN
Power Supply Input. · p. 17
20 OUT
System Output Terminal. · p. 17
21 VSS
Exposed Thermal Pad; internally connected to VSS and must connect to the same potential as VSS on the PCB. · p. 17

Open-source boards using it

2
  • 2 layers100 × 68.1 mmSnaphat pcb, the printed circuit board in 3D

    Snaphat pcb

    marchmare/snaphat-pcb

    RaspberryPi Zero 2 W addon serving as a handheld photo camera setup

    116 parts4Apache-2.0
  • 4 layers30 × 34.6 mmKeyboard QFAA, the printed circuit board in 3D

    Keyboard QFAA

    anhenaobe/nrf52840-modular-wireless-som

    Reusable four-layer nRF52840 wireless SoM with BLE, USB-C, LiPo charging, buck-boost power management, RF antenna integration, and manufacturing-ready outputs.

    66 partsGPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the MCP73871T-2CCI/ML?

Yes. The symbol is Battery_Management:MCP73871 and the footprint Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MCP73871T-2CCI/ML?

QFN-20-EP(4x4), with 21 pins. Its footprint is drawn on this page.

Where is the MCP73871T-2CCI/ML datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the MCP73871T-2CCI/ML?

JLCPCB lists it as part C511310, with 1,038 in stock; the sellers' links on this page open their listings.

What can replace the MCP73871T-2CCI/ML?

Parts like it in the library: the MCP73871-2CCI/ML by Microchip Technology, the MCP73871-2CAI/ML by Microchip Technology, the MCP73871-2AAI/ML by Microchip Technology and the ADP5063ACPZ-1-R7 by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the MCP73871T-2CCI/ML?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.