
Europe ergo smd
Supermagnum/Europe-ergo
A 94 key ergonomic, split keyboard suitable for European countries.

The goal of this project was to create a professional, competition-ready button box featuring plug-in terminals, an OLED display for testing and diagnostics, an indicator LED, and a large logo of my FRC Team 5402…
BUTTON BOX is an open-source printed circuit board by Gusus169, from the Gusus169/FRC-Button-box repository on GitHub, published under the MIT licence. It is a 2-layer board of 236.8 × 130.7 mm with 46 parts on 78 nets, routed with 316 tracks and 45 vias.
It is built around the SC0915 and 1N4148W. Its parts include 31 diodes, 6 connectors, 1 resistor and 1 IC.
Reliability is critical in FIRST Robotics Competition (FRC), especially during matches where a single equipment failure can affect an entire game. One component that many teams depend on is a button box, which provides drivers with quick access to robot functions that would otherwise be difficult to control through a standard controller alone. Rather than relying on a commercially available solution, I decided to design a custom button box PCB tailored to my team's needs.
The goal of this project was to create a professional, competition-ready button box featuring plug-in terminals, an OLED display for testing and diagnostics, an indicator LED, and a large logo of my FRC Team 5402, Wreckless Robotics, integrated directly into the PCB design. Throughout the project, I researched existing button boxes used by other FRC teams, selected components through DigiKey, designed the schematic in KiCad, created the PCB layout, and prepared the board for manufacturing. Along the way, I learned more about PCB design, component libraries, footprint management, routing techniques, and design-for-manufacturing considerations.
This repository documents the complete development process, including planning, schematic design, PCB layout, manufacturing files, and project documentation. The finished design will be used to support driver practice and competition preparation for Team 5402 while providing a reliable and maintainable control interface for future seasons.
Front-
Back-
-Large Team Logo (very important) -Flexibility – features 30 independent ports where buttons can be plugged in; no fixed sequence required, just plug-and-play
-Buttons can be swapped or replaced within a minute
-Uses a Raspberry Pi Pico (RP2040), allowing buttons to be programmed as needed for different FRC sessions
-Supports advanced logic such as button pairing and conditional inputs
-Designed for reliability – minimal excess components, reducing potential points of failure
-Includes an indicator LED for button box status
-Features a 0.91" OLED display for individual button testing and diagnostics
-Includes mounting holes to securely fasten the PCB in an enclosure or driver station setup
Schematic-
PCB Front-
PCB Back-
| Qty | Component | Value / Part Number |
|---|---|---|
| 1 | OLED Display | SSD1306 0.91" 128×32 |
| 1 | LED | 3mm LED |
| 30 | Diode | 1N4148W |
| 6 | Terminal Block Connector | Phoenix 1792944 |
| 1 | Resistor | 330 Ω |
| 1 | Microcontroller | Raspberry Pi Pico (RP2040) |
MIT
| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | 1N4148W | Diode_SMD:D_SOD-123 | D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24 +14 |
| 6 | 1792944 | COMPONENTS:PHOENIX_1792944 | J1, J2, J3, J4, J5, J6 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | LOGO | COMPONENTS:wreckless logo | G***, G*** |
| 1 | 330 ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | SC0915 | COMPONENTS:pi pico | U1 |
| 1 | SSD1306 | RGB sk:SSD1306-0.91-OLED-4pin-128x32 | Brd1 |

Supermagnum/Europe-ergo
A 94 key ergonomic, split keyboard suitable for European countries.

Rack-Robotics/Powercore-V3
electrical-discharge power supply, open-source


jackw01/pi-pico-printer-board
Tinkerer-friendly Klipper compatible 3D printer control board using Raspberry Pi Pico


lambdaBoost/MC6205-graphical-display
graphical display on old neon plasma screen


It measures 236.8 × 130.7 mm and has 2 copper layers, 1.6 mm thick.
46 parts, built around the SC0915 and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Gusus169/FRC-Button-box repository on GitHub, at the commit this page was made from: the board is KiCad Files/BUTTON BOX.kicad_pcb and its schematic KiCad Files/BUTTON BOX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).