

STM32F722RET Based brushed flight controller board
- Size
- 29 × 29 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 90
- Nets
- 92
- Pads
- 309
- Tracks, vias
- 429, 198
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 10 Apr 2024
- Updated
- 7 May 2024
Overview
BATF7 is an open-source printed circuit board by EIectron, from the EIectron/BATF7-Brushed-FC repository on GitHub. It is a 4-layer board of 29 × 29 mm with 90 parts on 92 nets, routed with 429 tracks and 198 vias.
It is built around the MS5611-01BA03, MPU-6500 and TPS63031DSK, with the SIS434DN, B3U-1000P and BC817 among its other parts. Its parts include 21 resistors, 18 capacitors, 7 diodes, 7 transistors and 6 ICs. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
8MS5611-01BA03
QFN-8(3x5)QFN-8(3x5) Pressure Sensors ROHSMEASPressure SensorsMPU-6500
QFN-24-40℃~+85℃ 16bit 6uA Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(3x3) Accelerometers ROHSTDK InvenSenseAccelerometersTPS63031DSK
UncategorisedTexas InstrumentsSIS434DN
PowerPAK1212-8-55℃~+150℃ 1 N-channel 1.2V 1.53nF 100pF 12.5nC@10V 35A 40V 7.6mΩ@10V PowerPAK1212-8 MOSFETs ROHSVishay IntertechnologyMOSFETsB3U-1000P
SMD,3x2.5mm-25℃~+70℃ 1.53N 1.6mm 12V 2.5mm 3mm 50mA Round Button SMD(SMT) Tab SPST Surface Mount,Vertical SMD,3x2.5mm Tactile Switches ROHSOmronTactile SwitchesBC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)IRLML6402
SOT-23-55℃~+150℃ 1 P-Channel 1.3W 110pF 12nC 145pF 20V 3.7A 400mV 633pF 65mΩ@4.5V P-Channel SOT-23 MOSFETs ROHSGuangdong HottechMOSFETsMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
Hardware/README.mdBATF7
V1
Key Features
- ARM Cortex-M7 core F7 216 MHz CPU
- Invensense MPU-6500 Six-Axis (Gyro + Accelerometer) low power consumption MEMS MotionTracking™ Device
- Blackbox logging via onboard dataflash chip
- Battery polarity reversed connection protection. The fc board remains perfect even if you plug the battery in wrong way.
- Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
- Designed to work with current Whoop Drone or Blade Inductrix setups
- The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Specifications
- CPU:
STM32F411CEU6 - Six-Axis:
MPU6500 - ESC: All FETs are rated at 35A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
- Size: 29mm x 29mm, fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BATF7 3.5.0
- Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
- Weight: 4.2g
Parts
90| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C4, C5, C6, C9, C10, C11, C12, C13, C14, C15, C17, C18, C19 |
| 11 | 10K | Resistor_SMD:R_0402_1005Metric | R1, R2, R4, R5, R10, R16, R17, R18, R19, R20, R21 |
| 5 | 1N5819 | Alperen:SOD-323 | D1, D4, D5, D6, D7 |
| 4 | 53047-0210 | Connector_Molex:Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | M1, M2, M3, M4 |
| 4 | MountingHole | Library:MH32 | H1, H2, H3, H4 |
| 4 | SIS434DN | Library:PPAK1212-8 | Q4, Q5, Q6, Q7 |
| 3 | 470R | Resistor_SMD:R_0402_1005Metric | R13, R14, R15 |
| 2 | 22R %1 | Resistor_SMD:R_0402_1005Metric | R6, R7 |
| 2 | 4.7K | Resistor_SMD:R_0402_1005Metric | R11, R12 |
| 1 | + | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | J2 |
| 1 | - | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | J3 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 1051330011 | Connector_USB:USB_Micro-B_Molex-105133-0031 | J4 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | 15K %1 | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 1S Lipo | Library:1x02-Long-Pad | J1 |
| 1 | 1uH | Inductor_SMD:L_Murata_DFE201610P | L1 |
| 1 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 220R | Inductor_SMD:L_0603_1608Metric | L2 |
| 1 | 22K %1 | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 500mA/6V | Fuse:Fuse_0805_2012Metric | F1 |
| 1 | 5020 | Alperen:ABMT-801-RC_PIEZO | U6 |
| 1 | 8MHz | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | B3U-1000P | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | IRLML6402 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | LIGHT | Capacitor_SMD:C_0805_2012Metric | J5 |
| 1 | LOGO | LOGO | G*** |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | MPU-6500 | Alperen:MPU6500 | U3 |
| 1 | MS5611-01BA | Package_LGA:LGA-8_3x5mm_P1.25mm | U4 |
| 1 | NRST | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | PB0 | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | RX | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | STM32F722RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | SWDIO | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | SWO | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | TPS63031DSK | Package_SON:WSON-10-1EP_2.5x2.5mm_P0.5mm_EP1.2x2mm | U1 |
| 1 | TX | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | U1_RX | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | U1_TX | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | VDD | TestPoint:TestPoint_Pad_1.0x1.0mm | TP8 |
| 1 | W25Q80DVUXIE-TR | Alperen:8-USON | U5 |
The 89 most common of 90 parts.
Similar boards
- 4 layers35 × 34 mm

- 2 layers50 × 75 mm

- 2 layers141.8 × 151.3 mm

- 4 layers54.7 × 78.5 mm

DisplayModule PONSv71
MasaoC/GPS-TFT-Map_PONS
鳥人間コンテストに特化したGNSS誘導システム。人力飛行機のパイロットが使いやすいことを目標にした航法装置です。ハードとソフトをオープンソースで開発しています。
151 parts14MIT - 2 layers100 × 72.8 mm

- 2 layers80 × 74 mm

Hubble metal detector
zartarn15/hubble-metal-detector
STM32-based digital metal detector with custom hardware and embedded DSP firmware.
156 parts2 - 6 layers42.2 × 61.4 mm

Dap proto board full
tsar-boomba/dap-proto-board-full
The culmination of all of my learning during the Spring '26 semester. All the way from making a simple dev board for the TAD5212 DAC, to making a RP2350 board, and now this. Everything combined on one 6-layer board.
102 parts1 - 2 layers100 × 100 mm

Hour meter board microfit can handroute
ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator
152 parts
Questions
How big is the BATF7 PCB?
It measures 29 × 29 mm and has 4 copper layers, 1.6 mm thick.
What parts does the BATF7 use?
90 parts, built around the MS5611-01BA03, MPU-6500, TPS63031DSK and SIS434DN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BATF7 KiCad files?
From the EIectron/BATF7-Brushed-FC repository on GitHub, at the commit this page was made from: the board is Hardware/BATF7.kicad_pcb and its schematic Hardware/BATF7.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BATF7 design in my own project?
Its repository states no licence, so its author keeps all rights: ask EIectron before reusing the design.