Skip to the content
2 layers50 × 50 mmMotor driver, the printed circuit board in 3D

it is a very simple motor driver that will recive the data from another micro-controller

Size
50 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
18
Pads
58
Tracks, vias
140, 13
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
14 Jul 2026
Updated
14 Jul 2026

Overview

Motor driver is an open-source printed circuit board by Dhruv2212-star, from the Dhruv2212-star/Motor-driver repository on GitHub. It is a 2-layer board of 50 × 50 mm with 14 parts on 18 nets, routed with 140 tracks and 13 vias.

It is built around the AO3407A, MF-R250 and SMBJ15A. Its parts include 5 capacitors, 4 connectors, 1 resistor, 1 IC and 1 diode. It belongs with the robots and motor control boards of this library.

Main components

3

README

README.md

The schematic is divided into 2 parts for easier designing-

  1. Power distribution system

  2. Logic system

  3. Block 1 – Power System Objective-

The Power System is responsible for receiving power from the battery, protecting the circuit from electrical faults, filtering supply noise, and delivering a clean, protected power rail to the motor driver IC. Every component in this block contributes to either protection, power conditioning, or power distribution.

RefComponentSelected PartWhy this part was used and what role it plays
J1Power Input ConnectorPhoenix Contact MKDS 1,5/2-5.08J1 serves as the entry point for the external power supply. A screw terminal was selected because it provides a secure, reliable, and vibration-resistant connection for battery wires while allowing easy installation and removal during testing or maintenance.
F1Resettable PolyfuseBourns MF-R250The MF-R250 was chosen to protect the entire PCB from excessive current caused by short circuits or wiring faults. Unlike a traditional fuse, it automatically resets after the fault is removed, eliminating the need for replacement. It is placed immediately after the power connector so every downstream component is protected.
Q1P-Channel MOSFETAO3407AThe AO3407A was selected to provide reverse-polarity protection with almost no voltage drop. If the battery is connected correctly, the MOSFET conducts normally with very low resistance. If the battery is connected in reverse, it blocks current completely, preventing damage to the rest of the circuit. This method is significantly more efficient than using a series diode.
R1Gate Pull-Down Resistor100 kΩThe 100 kΩ resistor ensures that the MOSFET gate is always held at a defined voltage during power-up and power-down. This guarantees predictable switching behavior and prevents the MOSFET from turning on unintentionally due to electrical noise or a floating gate.
D1TVS DiodeSMBJ15AThe SMBJ15A TVS diode was selected to protect the circuit from sudden voltage spikes and transients generated by motors, wiring inductance, or external power disturbances. Under normal operating conditions it remains inactive, but during an over-voltage event it quickly clamps the voltage to a safe level, protecting sensitive components.
C1Bulk Capacitor470 µF, 25 V ElectrolyticC1 acts as the primary energy reservoir for the motor supply. Motors can draw large bursts of current during startup or rapid direction changes, causing the supply voltage to dip. This capacitor supplies that short-term current, reducing voltage fluctuations and improving overall system stability.
C2Decoupling Capacitor100 nF CeramicWhile C1 handles low-frequency voltage fluctuations, C2 removes high-frequency electrical noise generated by switching circuits and motor commutation. Ceramic capacitors have very low impedance at high frequencies, making them ideal for filtering fast voltage spikes that electrolytic capacitors cannot effectively suppress.
  1. Block 2 – Motor Driver System Objective-

The Motor Driver System receives logic commands from an external microcontroller and controls two DC motors using the TB6612FNG dual H-bridge driver. It also provides the required power conditioning for the IC and exposes the motor outputs through dedicated connectors.

RefComponentSelected PartWhy this part was used and what role it plays
U1Dual H-Bridge Motor DriverTB6612FNGThe TB6612FNG was selected because it is a reliable dual H-bridge motor driver capable of independently controlling two DC motors. It supports PWM speed control, forward/reverse operation, braking, and standby mode while offering significantly lower power loss than older bipolar motor drivers such as the L298N.
J2Logic Interface Header1×9 Pin HeaderJ2 provides the electrical interface between the motor driver PCB and an external microcontroller such as an STM32, Arduino, or ESP32. It carries all required logic signals including PWM inputs, direction control, standby control, logic power, and ground.
J3Motor A ConnectorPhoenix Contact MKDS 1,5/2-5.08J3 provides a secure connection between the motor driver outputs and Motor A. A screw terminal was selected to allow easy connection and replacement of motors while providing reliable electrical contact under vibration and higher current conditions.
J4Motor B ConnectorPhoenix Contact MKDS 1,5/2-5.08J4 performs the same function as J3 for Motor B, providing a durable and removable connection for the second motor output.
C3Logic Supply Decoupling Capacitor100 nF CeramicC3 stabilizes the logic supply (VCC) of the TB6612FNG by filtering high-frequency noise. This prevents disturbances from affecting the IC's internal control circuitry and improves overall reliability.
C4Motor Supply Decoupling Capacitor100 nF CeramicC4 filters high-frequency switching noise present on the motor supply (VM). It is positioned close to the motor driver IC to minimize voltage spikes caused by the rapid switching of the internal MOSFETs.
C5Bulk Motor Supply Capacitor10 µF, 25 V ElectrolyticC5 provides additional local energy storage directly beside the motor driver IC. During sudden motor current demands, it supplies instant current to the TB6612FNG, helping maintain a stable VM supply and reducing voltage dips on the PCB.

Parts

14
QtyValueFootprintReferences
3Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ1, J3, J4
2100 nFCapacitor_SMD:C_0805_2012MetricC3, C4
110 µF, 25 VCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC5
1100 kΩ, 1%Resistor_SMD:R_0805_2012MetricR1
1100 nF, 50 VCapacitor_SMD:C_0805_2012MetricC2
1470 µF, 25 VCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC1
1AO3407APackage_TO_SOT_SMD:SOT-23Q1
1Conn_01x09_PinConnector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_VerticalJ2
1MF-R250Fuse:Fuse_Bourns_MF-RG300F1
1SMBJ15ADiode_SMD:D_SMBD1
1TB6612FNGPackage_SO:SSOP-24_5.3x8.2mm_P0.65mmU1

Similar boards

  • 2 layers90 × 70 mmMidi s3 mini, the printed circuit board in 3D

    Midi s3 mini

    usr-ein/TriMixxx

    Open source standalone DJ multimedia player, compatible with Rekordbox

    102 parts44GPL-3.0
  • 4 layers152.4 × 96.5 mmFdmbox pcb tiny, the printed circuit board in 3D

    Fdmbox pcb tiny

    gdck/fdmbox_pcb_tiny

    Tiny PCB for a great FDM 3d printer

    132 partsGPL-3.0
  • 2 layers170 × 105 mmSsio check, the printed circuit board in 3D

    Ssio check

    paulbruneau/ssio-check

    A bench tester for the Bally/Midway MCR Sound I/O family: the 90908 Sound I/O and the 90913 / 91483 / 91657 Super Sound I/O (Z80, two AY-3-8910s, and all of the game's input ports).

    72 parts
  • 2 layers53.5 × 46 mmNodeNet PWR Module, the printed circuit board in 3D

    NodeNet PWR Module

    stephentissot/NodeNet-SoC-Risc-v

    Hello World project on Colorlight i9 FPGA

    14 partsMIT
  • 6 layers36 × 124 mmOpenDual Reader, the printed circuit board in 3D

    OpenDual Reader

    nuerolynx/embedded-systems-lab

    Arduino UNO R4 WiFi and ESP32 prototypes for access control, automation, displays, monitoring, and Bluetooth audio.

    74 parts4
  • 8 layers217.5 × 187.5 mmBoard c openroute partial, the printed circuit board in 3D

    Board c openroute partial

    ajisrawi/passive-radar-counter-drone

    Passive radar for counter-drone using DVB-T, 4G and 5G: simulation, receiver hardware, FPGA micro-Doppler firmware, antennas, enclosure

    314 parts3
  • 2 layers170.6 × 121.1 mmEIM, the printed circuit board in 3D

    EIM

    bhorst519/bluecar

    232 parts3
  • 4 layers220 × 120 mmCandidate filled profile, the printed circuit board in 3D

    Candidate filled profile

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    569 parts3MIT

Questions

How big is the Motor driver PCB?

It measures 50 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Motor driver use?

14 parts, built around the AO3407A, MF-R250 and SMBJ15A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Motor driver KiCad files?

From the Dhruv2212-star/Motor-driver repository on GitHub, at the commit this page was made from: the board is PCB/Motor driver.kicad_pcb and its schematic PCB/Motor driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Motor driver design in my own project?

Its repository states no licence, so its author keeps all rights: ask Dhruv2212-star before reusing the design.