Skip to the content
123456

TPS56339DDC

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 3A 4.5V~24V 500kHz 800mV~16V 98uA Adjustable Buck Buck Built-in Yes TSOT-23-6 DC-DC Converters ROHS

Part id
ti/TPS56339DDC
Category
DC DC Converters
Package
TSOT-23-6
Pins
6
In stock
12,323 at JLCPCB (C2071106)
Used on
26 open-source boards

Overview

The TPS56339DDC is a DC DC Converter made by Texas Instruments in a TSOT-23-6 package with 6 pins. -40℃~+125℃@(TJ) 1 3A 4.5V~24V 500kHz 800mV~16V 98uA Adjustable Buck Buck Built-in Yes TSOT-23-6 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:TPS56339DDC, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 12,323 are in stock at JLCPCB (part C2071106). 26 open-source boards in 24 repositories on GitHub use it.

Symbol

1GND2SW3VIN4FB5EN6BOOT
Regulator_Switching:TPS56339DDCFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

14
Supply, least
4.5 V · VIN, recommended operating min · p. 4
Supply, most
24 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
26 V · VIN, absolute max · p. 4
Junction, hottest
150 °C · Junction temperature, absolute max · p. 4
Takes working
98 µA · VIN, typical non switching quiescent current; no load, VIN = 12 V, VFB = 1.2 V · p. 5
Takes asleep
3 µA · VIN, typical shutdown current; VIN = 12 V, VEN = 0 V · p. 5
Gives
3 A · Continuous output current max · p. 1
Current limit
4.7 A · High-side MOSFET current limit typical · p. 5
Current limit
3.6 A · Low-side MOSFET current limit typical; VIN = 12 V · p. 5
Feedback reference
802 mV · Feedback reference typical; TJ = 25 °C · p. 5
Switches at
500 kHz · Switching frequency typical · p. 5
Junction to air (DDC (SOT23))
119.1 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DDC (SOT23))
58.1 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (DDC (SOT23))
36.7 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

11
Output voltage range
0.8 V to 16 V · p. 1
Maximum duty cycle
97% · p. 1
Integrated MOSFETs
70-mΩ and 35-mΩ · p. 1
Soft-start
Internal 5 ms · p. 1
Loop compensation
Internal · p. 1
Protection
Non-latched UVP, UVLO and TSD · p. 1
Package
SOT-23 (6) · p. 1
Soft start
Internal, 5 ms · p. 12
Voltage reference accuracy
±2.5% over full temperature · p. 12
Overcurrent protection
Cycle-by-cycle peak and valley inductor current limiting · p. 13
Thermal shutdown
160°C typical · p. 13

Around it

24
res 30 Ω
between BOOT and SW; Boot resistor in the bootstrap network with the required capacitor. · p. 3
cap 0.1 μF
between BOOT and SW; Bootstrap capacitor with the required boot resistor; carries high-side MOSFET gate drive voltage. · p. 3
cap over 10 µF
between VIN and GND; Ceramic input decoupling capacitor; additional bulk capacitance depends on the application. · p. 18
cap 0.1-µF
between VIN and GND; C3, additional high frequency filtering. · p. 18
cap 0.1-µF
between BOOT and SW; Ceramic bootstrap capacitor, X5R or better, rated at least 10 V; connect through the required series bootstrap resistor. · p. 18
res 30-Ω
between BOOT and C4; R3, required series bootstrap resistor. · p. 18
res 174 kΩ
between VIN and EN; Example UVLO upper resistor R1 for 6.6 V start and 5.7 V stop thresholds. · p. 18
res 36.5 kΩ
between EN and GND; Example UVLO lower resistor R2 for 6.6 V start and 5.7 V stop thresholds. · p. 18
cap Two 22-uF
between VOUT and GND; Recommended for VOUT ≤ 5 V; 0805, 16 V. · p. 17
cap three 22-uF
between VOUT and GND; Recommended for VOUT > 5 V; 0805, 25 VDC. · p. 17
ind 1.5 µH
between SW and VOUT; Recommended L1 for 1.05 V output with 2×22 uF nominal output capacitance. · p. 17
ind 2.2 µH
between SW and VOUT; Recommended L1 for 1.8 V output with 2×22 uF nominal output capacitance. · p. 17
ind 3.3 µH
between SW and VOUT; Recommended L1 for 2.5 V output with 2×22 uF nominal output capacitance. · p. 17
ind 4.7 µH
between SW and VOUT; Recommended L1 for 3.3 V output with 2×22 uF nominal output capacitance. · p. 17
ind 5.6 µH
between SW and VOUT; Recommended L1 for 5 V output with 2×22 uF nominal output capacitance. · p. 17
ind 6.8 µH
between SW and VOUT; Recommended L1 for 12 V output with 3×22 uF nominal output capacitance. · p. 17
res 3.16 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 1.05 V output. · p. 17
res 12.4 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 1.8 V output. · p. 17
res 21.5 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 2.5 V output. · p. 17
res 31.6 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 3.3 V output. · p. 17
res 52.3 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 5 V output. · p. 17
res 140 kΩ
between VOUT and FB; Recommended upper feedback resistor R6 for 12 V output. · p. 17
res 10.0 kΩ
between FB and GND; Recommended lower feedback resistor R7 for the listed output voltage configurations. · p. 17
res 0 Ω
between VOUT and FB; R6 for 0.8 V output. · p. 17

Specifications

50
ParameterConditionsAs printedPage
Input voltages VINmin -0.3 · max 26 V4
Input voltages ENmin -0.3 · max 6 V4
Input voltages BOOTMaximum: SW+6 Vmin -0.3 V4
Input voltages FBmin -0.3 · max 6 V4
Output voltages BOOT-SWmin -0.3 · max 6 V4
Output voltages SWmin -0.3 · max 26 V4
Output voltages SW<10 ns transientmin -3 · max 26 V4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±500 Vmax 500 V4
Input voltage VINmin 4.5 · max 24 V4
Input voltage ENmin -0.1 · max 5.5 V4
Input voltage FBmin -0.1 · max 5.5 V4
Output voltage BOOT-SWmin -0.1 · max 5.5 V4
Output voltage SWmin -0.1 · max 24 V4
Ouput Current IOUTmin 0 · max 3 A4
Operating junction temperature, TJ TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADDC (SOT23), 6 PINStyp 119.1 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DDC (SOT23), 6 PINStyp 58.1 °C/W4
Junction-to-board thermal resistance RθJBDDC (SOT23), 6 PINStyp 36.7 °C/W4
Junction-to-top characterization parameter ΨJTDDC (SOT23), 6 PINStyp 9.4 °C/W5
Junction-to-board characterization parameter ΨJBDDC (SOT23), 6 PINStyp 36.2 °C/W5
Operation input voltage VINTJ = –40°C to +125°Cmin 4.5 · max 24 V5
Non switching quiescent current IQFirst power on with no load, then force VFB to 1.2 V, VIN = 12 Vtyp 98 uA5
Shutdown supply current ISHDNVIN = 12 V, VEN = 0 Vtyp 3 uA5
Undervoltage lockout thresholds VIN_UVLOVIN Rising thresholdmin 3.9 · typ 4.2 · max 4.4 V5
Undervoltage lockout thresholds VIN_UVLOVIN Falling thresholdmin 3.5 · typ 3.7 · max 3.9 V5
Enable threshold VEN_RISEEN rising thresholdtyp 1.18 · max 1.28 V5
Enable threshold VEN_FALLEN falling thresholdmin 1.08 · typ 1.12 V5
Input current IEN_INPUTVEN = 1.0 Vtyp 1.2 uA5
Hysteresis current IEN_HYSVEN = 1.5 Vtyp 3.1 uA5
Reference voltage VREFTJ = 25 °Cmin 0.79 · typ 0.802 · max 0.814 V5
Reference voltage VREFTJ = -40 °C to 125 °Cmin 0.782 · typ 0.802 · max 0.822 V5
High-side MOSFET On-resistance RDS_ON_HSTJ = 25 °C, VBOOT-SW = 5 Vtyp 70 mΩ5
Low-side MOSFET On-resistance RDS_ON_LSTJ = 25 °C, VIN = 12 Vtyp 35 mΩ5
High-side MOSFET current limit IHS_LIMITmin 3.9 · typ 4.7 · max 5.4 A5
Low-side MOSFET current limit ILS_LIMITVIN = 12 Vmin 2.7 · typ 3.6 · max 4.7 A5
Output UVP thresholdHiccup detect (H→L)typ 62.5 %5
Hysteresis VUVP_HYSOutput undervoltage protectiontyp 5 %5
BOOT UVLO threshold VBOOT-SWtyp 2.2 V5
Switching frequency fSWmin 420 · typ 500 · max 600 KHz5
Thermal shutdown threshold TSHDNNot production testedtyp 160 °C5
Hysteresis THYSThermal shutdown; not production testedtyp 20 °C5
Minimum on time TON_MINVIN = 4.5 V to 24 V; not production testedtyp 55 ns6
Maximum on time TON_MAXVIN = 4.5 V to 24 Vtyp 5 us6
Minimum off time TOFF_MINVIN = 4.5 V to 24 Vtyp 115 ns6
Internal soft-start time TSSVIN = 4.5 V to 24 Vtyp 5 ms6
Hiccup on time THIC_WAITVIN = 4.5 V to 24 Vtyp 120 us6
Hiccup time before restart THIC_REVIN = 4.5 V to 24 Vtyp 38 ms6

Pins, by the datasheet

6
1 GND
Ground for the controller and source terminal of the low-side MOSFET; connect sensitive FB to this GND at a single point. · p. 3
2 SW
Switch node connection between high-side MOSFET and low-side MOSFET. · p. 3
3 VIN
Input voltage supply pin and drain terminal of the high-side MOSFET. · p. 3
4 FB
Converter feedback input; connect to output voltage with a feedback resistor divider. · p. 3
5 EN
Enable pin; float to enable, or adjust input undervoltage lockout with two resistors. · p. 3
6 BOOT
Connect a 30-Ω boot resistor and 0.1-uF bootstrap capacitor between BOOT and SW to supply high-side MOSFET gate drive. · p. 3

Ordering codes, by the datasheet

4
TPS56339DDCR
SOT-23-THIN (DDC), 6 pins · 3000 units, LARGE T&R · p. 25
TPS56339DDCR.A
SOT-23-THIN (DDC), 6 pins · 3000 units, LARGE T&R · p. 25
TPS56339DDCT
SOT-23-THIN (DDC), 6 pins · 250 units, SMALL T&R · p. 25
TPS56339DDCT.A
SOT-23-THIN (DDC), 6 pins · 250 units, SMALL T&R · p. 25

Open-source boards using it

26See all 26
  • 4 layers150 × 50 mmEmber, the printed circuit board in 3D

    Ember

    notaroomba/ember

    A custom hot plate powered by USB-C Power Delivery.

    136 parts25
  • 4 layers100 × 100 mmPlantomation V2, the printed circuit board in 3D

    Plantomation V2

    Synthron/Plantomation

    DIY plant watering system

    203 parts10
  • 2 layers95 × 35 mmSynth psu, the printed circuit board in 3D

    Synth psu

    mattvenn/usbc-synth-psu

    For build notes, problems and fixes, please check the project log

    91 parts2
  • 2 layers95 × 99 mmPolaris4.1, the printed circuit board in 3D

    Polaris4.1

    porbital/GNC_Hapsis

    Software for the GNC Hapsis launch structure control system

    95 parts2
  • 2 layersInter assignment, the printed circuit board in 3D

    Inter assignment

    Arpit192005/Buck-converter-using-TPS56339DDC

    12 parts1
  • 4 layers46 × 56 mmLINBoard HW, the printed circuit board in 3D

    LINBoard HW

    corygrant/LINBoard

    73 parts1
  • 4 layers101 × 51.5 mmQuack core, the printed circuit board in 3D

    Quack core

    HeyPCB/quack-core

    Brain board for the Open Duck Mini: Pi Zero 2W carrier, 14-servo STS bus, fused 2S power path in stitched copper zones (15-18 A battery side), USB-C charging with balancing, IMU.

    138 parts1CERN-OHL-S-2.0
  • 2 layers304.3 × 274 mmRobotont electronics mainboard, the printed circuit board in 3D

    Robotont electronics mainboard

    robotont/robotont-electronics-mainboard

    Unified pcb design for the 3rd generation robotont robot.

    426 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS56339DDC?

Yes. The symbol is Regulator_Switching:TPS56339DDC and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS56339DDC?

TSOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the TPS56339DDC datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS56339DDC?

JLCPCB lists it as part C2071106, with 12,323 in stock; the sellers' links on this page open their listings.

What can replace the TPS56339DDC?

Parts like it in the library: the TPS54302DDC by Texas Instruments, the MT3608B by XI'AN Aerosemi Tech, the SY8113IADC by 矽力杰silergy and the HFP6291LR-G1 by HXY MOSFET. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS56339DDC?

26 boards in 24 repositories on GitHub; the most starred are listed on this page, with their KiCad files.