Skip to the content
123456

TLV61048DBV

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 100uA 2.65V~5.5V 3.3V~14V 550kHz、1MHz Adjustable Boost Boost Built-in No SOT-23-6 DC-DC Converters ROHS

Part id
ti/TLV61048DBV
Category
DC DC Converters
Package
SOT-23-6
Pins
6
In stock
13,858 at JLCPCB (C2861467)
Used on
8 open-source boards

Overview

The TLV61048DBV is a DC DC Converter made by Texas Instruments in a SOT-23-6 package with 6 pins. -40℃~+125℃@(TJ) 1 100uA 2.65V~5.5V 3.3V~14V 550kHz、1MHz Adjustable Boost Boost Built-in No SOT-23-6 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TLV61048DBVT, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 13,858 are in stock at JLCPCB (part C2861467). 8 open-source boards in 8 repositories on GitHub use it.

Symbol

1SW2GND3FB4EN5VIN6FREQ
EasyEDA_Cloud:TLV61048DBVTFrom EasyEDA

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

14
Supply, least
2.65 V · VIN, recommended operating minimum · p. 4
Supply, most
5.5 V · VIN, recommended operating maximum · p. 4
Supply, absolute maximum
6 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 4
Takes working
100 µA · VIN quiescent current, typical, enabled, no load, no switching · p. 5
Takes asleep
1 µA · VIN shutdown current, max, disabled, VIN = 2.6–5.5 V, TA = 25°C · p. 5
Current limit
3.7 A · Peak switch current limit, typical, 600 kHz, VIN = 3.3 V · p. 5
Feedback reference
800 mV · FB feedback voltage, typical, PWM mode, TA = −40°C to 125°C · p. 5
Feedback reference
810 mV · FB feedback voltage, typical, PFM mode, TA = 25°C · p. 5
Switches at
550 kHz · Switching frequency, typical, lower frequency setting, VIN = 3.3 V, VOUT = 12 V, PWM · p. 5
Switches at
1 MHz · Switching frequency, typical, higher frequency setting, VIN = 3.3 V, VOUT = 12 V, PWM · p. 5
Junction to air (DBV (SOT23))
177.7 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DBV (SOT23))
120.6 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (DBV (SOT23))
33.2 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

10
Output voltage
Up to 14 V · p. 1
Integrated low-side FET
85 mΩ at 3.3 VIN · p. 1
Switch current limit
3.7 A typical · p. 1
Switching frequency selection
600 kHz or 1 MHz · p. 1
Compensation
Internal · p. 1
Output-voltage accuracy
±2.5% · p. 1
Light-load operation
PFM · p. 1
Soft start
Internal, 2 ms · p. 1
Protection
Thermal shutdown · p. 1
Package
2.9-mm × 1.6-mm 6-Pin SOT-23 · p. 1

Around it

7
ind 2.2 µH to 10 µH
between Power input and SW; Boost inductor; select saturation current and DCR for the application. · p. 11
res smaller than 150 kΩ
between FB and GND; R2, the lower feedback divider resistor, for best accuracy. · p. 11
cap 3.3 µF to 10 µF
between VOUT and GND; Effective output capacitance for the 600-kHz configuration. · p. 12
cap 1 µF
between Rectifier diode cathode and GND; Place directly across the rectifier cathode and the IC ground pin to reduce high RMS current loop inductance. · p. 12
cap more than 1 µF
between Power input and GND; Ceramic input capacitor; enough for most applications. · p. 12
diode 20 V, 1 A Schottky diode B120AF-13
between SW and VOUT; Rectifier selected for the 12 V output example; anode at SW and cathode at VOUT. · p. 12
cap 47 µF
between Power input and GND; Additional electrolytic or tantalum bulk capacitance when the input supply is more than a few inches from the converter. · p. 15

Specifications

42
ParameterConditionsAs printedPage
Voltage range at terminals (2)VIN, EN, FREQmin -0.3 · max 6 V4
Voltage range at terminals (2)SWmin -0.3 · max 18 V4
Voltage range at terminals (2)FBmin -0.3 · max 3.6 V4
Operating junction temperature range, TJ TJmin -40 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (2); value ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (3); value ±500 Vmax 500 V4
Input voltage range VINmin 2.65 · max 5.5 V4
Output voltage range VOUTmin 3.3 · max 14 V4
Effective inductance range Lmin 2.2 · typ 4.7 · max 10 uH4
Effective input capacitance range CINmin 0.22 · typ 1 uF4
Effective output capacitance range COUTmin 3 uF4
Operating junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJATLV61048, DBV (SOT23), 6 PINStyp 177.7 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)TLV61048, DBV (SOT23), 6 PINStyp 120.6 °C/W4
Junction-to-board thermal resistance RθJBTLV61048, DBV (SOT23), 6 PINStyp 33.2 °C/W4
Junction-to-top characterization parameter ψJTTLV61048, DBV (SOT23), 6 PINStyp 21.5 °C/W4
Junction-to-board characterization parameter ψJBTLV61048, DBV (SOT23), 6 PINStyp 32.6 °C/W4
Input voltage range VINTA = –40°C to 85°Cmin 2.65 · max 5.5 V5
Under voltage lockout threshold VIN_UVLOVIN risingtyp 2.55 · max 2.65 V5
Under voltage lockout threshold VIN_UVLOVIN fallingmin 2.3 · typ 2.4 V5
VIN UVLO hysteresis VIN_HYSTA = 25°Ctyp 150 mV5
Quiescent current into VIN pin IQ_VINIC enabled, no load, no switching; VIN = 3.3 V, TA = 25°Ctyp 100 uA5
Shutdown current into VIN pin ISDIC disabled, VIN = 2.6 V to 5.5 V, TA = 25°Cmax 1 uA5
Output voltage range VOUTTA = –40°C to 85°C, VIN = 3.3 Vmin 3.3 · max 14 V5
Feedback voltage VREFPWM mode, TA=-40°C to 125°Cmin 0.78 · typ 0.8 · max 0.82 V5
Feedback voltage VREFPFM mode, TA=25°Ctyp 0.81 V5
Leakage current into FB pin IFB_LKGTA = 25°Cmax 50 nA5
Leakage current into SW pin ISW_LKGIC disabled, SW = 5.5Vmax 500 nA5
Low-side MOSFET on resistance RDS(on)VIN = 3.3, VOUT = 12Vtyp 85 mΩ5
Switching frequency fSWVIN = 3.3 V, VOUT = 12 V, PWM mode; lower frequency settingmin 430 · typ 550 · max 630 kHz5
Switching frequency fSWVIN = 3.3 V, VOUT = 12 V, PWM mode; higher frequency settingmin 850 · typ 1000 · max 1250 kHz5
Min. off time tOFF_minVIN = 3.3 V, TA = 25°Ctyp 130 ns5
Peak switch current limit ILIM_SW600kHz, VIN = 3.3Vmin 2.9 · typ 3.7 · max 4.5 A5
Startup time tSTARTUPVIN = 3.3 V, TA = 25°Ctyp 2 ms5
EN Logic high threshold VEN_HTA = –40°C to 85°C, VIN = 3.3 Vmax 1.2 V5
EN Logic low threshold VEN_LTA = –40°C to 85°C, VIN = 3.3 Vmin 0.4 V5
EN Pull Down Resistor RENVIN = 3.3 V, TA = 25°Ctyp 1 MΩ5
FREQ pull up resistance RFREQVIN = 3.3 V, TA = 25°Ctyp 950 kΩ5
FREQ logic high threshold VFREQ_HTA = –40°C to 85°C, VIN = 3.3 Vmax 1.2 V5
FREQ logic low threshold VFREQ_LTA = –40°C to 85°C, VIN = 3.3 Vmin 0.4 V5
Thermal shutdown threshold TSDTJ risingtyp 150 °C5
Thermal shutdown hysteresis TSD_HYSTJ falling below TSDtyp 20 °C5

Pins, by the datasheet

6
1 SW
Converter switch pin connected to the drain of the internal power MOSFET. · p. 3
2 GND
Ground. · p. 3
3 FB
Output voltage feedback; connect to the center tap of a resistor divider to program the output voltage. · p. 3
4 EN
Logic high enables the device; logic low disables it and enters shutdown mode. · p. 3
5 VIN
IC power supply input. · p. 3
6 FREQ
Frequency selection: floating or high selects 600 kHz; connection to GND selects 1 MHz. · p. 3

Open-source boards using it

8
  • 2 layers52.8 × 55 mmILDAWaveX16, the printed circuit board in 3D

    ILDAWaveX16

    stanleyondrus/ILDAWaveX16

    ILDAWaveX16 is an open-source, high-resolution, wireless laser DAC with SD-card playback, network control, and ILDA output.

    95 parts42
  • 4 layers64 × 77 mmOBSPro, the printed circuit board in 3D

    OBSPro

    FabianSchwartau/OBSPro

    Version of the OpenBikeSensor hardware optimized for PCBA

    131 parts3LGPL-2.1
  • 4 layers36 × 60 mmSignal generator, the printed circuit board in 3D

    Signal generator

    NidasioAlberto/signal-generator

    Signal Generator with an STM32

    70 parts3
  • 4 layers45 × 53 mmOpenTRV ESP, the printed circuit board in 3D

    OpenTRV ESP

    mpiraux/OpenTRV-ESP

    An open-source and open-hardware thermostatic radiator valve based on the ESP32C6 and the 28BYJ-48 stepper motor.

    64 parts2CERN-OHL-P-2.0
  • 2 layers32 × 46 mmGeneral purpose step up, the printed circuit board in 3D

    General purpose step up

    marcusmueller/12V_step_up

    General purpose Step-Up converter

    26 partsCERN-OHL-S-2.0
  • 4 layers59.3 × 37.5 mmModule, the printed circuit board in 3D

    Module

    Pollex/MFM-Module-RS485

    A MultiFlexMeter (MFM) sensor module. The hardware is a generic carrier: RS-485 + 1-Wire, with a software-selectable sensor supply rail (3.6 V / 5 V / 12 V).

    56 parts
  • 2 layers36.4 × 14.9 mmBOOST CONVERTER, the printed circuit board in 3D

    BOOST CONVERTER

    tsokomalusi/TLV61048_BOOST_CONVERTER

    12 parts
  • 2 layers20 × 10 mmDrone bms, the printed circuit board in 3D

    Drone bms

    AMLing2/MAS500_Drone_Arena

    4 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV61048DBV?

Yes. The symbol is EasyEDA_Cloud:TLV61048DBVT and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV61048DBV?

SOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the TLV61048DBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV61048DBV?

JLCPCB lists it as part C2861467, with 13,858 in stock; the sellers' links on this page open their listings.

What can replace the TLV61048DBV?

Parts like it in the library: the MT3608B by XI'AN Aerosemi Tech, the HFP6291LR-G1 by HXY MOSFET, the TPS564201DDC by Texas Instruments and the TPS565208DDC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV61048DBV?

8 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.