Skip to the content
123456

TPS562201DDC

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 2A 380uA 4.5V~17V 580kHz 768mV~7V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting Step-down type Yes TSOT-23-6 DC-DC Converters ROHS

Part id
ti/TPS562201DDC
Category
DC DC Converters
Package
TSOT-23-6
Pins
6
In stock
547,591 at JLCPCB (C90061)
Used on
12 open-source boards

Overview

The TPS562201DDC is a DC DC Converter made by Texas Instruments in a TSOT-23-6 package with 6 pins. -40℃~+125℃@(TJ) 1 2A 380uA 4.5V~17V 580kHz 768mV~7V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting Step-down type Yes TSOT-23-6 DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Celestial_Power_Switchmode:TI TPS562201DDC, from Altium's library) and its footprint (Package_TO_SOT_SMD:TSOT-23-6, from KiCad's library), ready for a KiCad board. 547,591 are in stock at JLCPCB (part C90061). 12 open-source boards in 11 repositories on GitHub use it.

Symbol

1GND6VBST2SW4VFB3VIN5EN
Celestial_Power_Switchmode:TI TPS562201DDCFrom Altium's library

Footprint

123456
Package_TO_SOT_SMD:TSOT-23-6From KiCad's library

From the datasheet

14
Supply, least
4.5 V · VIN, recommended operating min · p. 4
Supply, most
17 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
19 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 4
Takes working
120 µA · VIN, typical operating non-switching current, EN = 5 V, VFB = 0.9 V · p. 5
Takes asleep
8 µA · VIN, typical shutdown current, EN = 0 V · p. 5
Gives
2 A · Maximum available continuous output current · p. 12
Current limit
3.2 A · Typical DC current limit, VOUT = 1.05 V, L1 = 2.2 uH · p. 5
Feedback reference
768 mV · Typical VFB threshold, continuous mode, VO = 1.05 V · p. 5
Feedback reference
774 mV · Typical VFB threshold, Eco-mode, VO = 1.05 V, IO = 10 mA · p. 5
Switches at
580 kHz · Typical switching frequency, VIN = 12 V, VO = 3.3 V, IO = 1 A · p. 5
Junction to air (DDC (SOT))
90.8 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DDC (SOT))
42.3 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (DDC (SOT))
16.3 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

9
Control
D-CAP2 control with fast transient response · p. 1
Output voltage range
0.76V to 7V · p. 1
Light-load operation
Pulse-skip mode · p. 1
Feedback voltage accuracy
2% at 25°C · p. 1
Startup
Start-up from prebiased output voltage · p. 1
Protection
Cycle-by-cycle overcurrent limit · p. 1
Protection
Hiccup-mode overcurrent protection · p. 1
Protection
Non-latch UVP and TSD protections · p. 1
Soft start
Fixed, 1.0ms · p. 1

Around it

1
cap 0.1-µF
between VBST and SW; High-side NFET gate-drive supply capacitor. · p. 3

Specifications

48
ParameterConditionsAs printedPage
Input voltageVIN, ENmin -0.3 · max 19 V4
Input voltageVBSTmin -0.3 · max 25 V4
Input voltageVBST (10-ns transient)min -0.3 · max 27 V4
Input voltageVBST (vs SW)min -0.3 · max 6 V4
Input voltageVFBmin -0.3 · max 6 V4
Input voltageSWmin -2 · max 19 V4
Input voltageSW (10 ns transient)min -3.5 · max 21 V4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -55 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001min -2000 · max 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101min -1500 · max 1500 V4
Supply input voltage VINmin 4.5 · max 17 V4
Input voltage VIVBSTmin -0.1 · max 23 V4
Input voltage VIVBST (10-ns transient)min -0.1 · max 26 V4
Input voltage VIVBST(vs SW)min -0.1 · max 5.5 V4
Input voltage VIENmin -0.1 · max 17 V4
Input voltage VIVFBmin -0.1 · max 5.5 V4
Input voltage VISWmin -1.8 · max 17 V4
Input voltage VISW (10 ns transient)min -3.5 · max 20 V4
Operating junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJATPS562201, DDC (SOT), 6 PINStyp 90.8 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)TPS562201, DDC (SOT), 6 PINStyp 42.3 °C/W4
Junction-to-board thermal resistance RθJBTPS562201, DDC (SOT), 6 PINStyp 16.3 °C/W4
Junction-to-top characterization parameter ψJTTPS562201, DDC (SOT), 6 PINStyp 2.6 °C/W4
Junction-to-board characterization parameter ψJBTPS562201, DDC (SOT), 6 PINStyp 16.3 °C/W5
Operating – non-switching supply current IVINTPS562201; VIN current, EN = 5 V, VFB = 0.9 Vtyp 120 · max 200 uA5
Shutdown supply current IVINSDNVIN current, EN = 0 Vtyp 8 · max 20 uA5
EN high-level input voltage VENHmin 1.6 V5
EN low-level input voltage VENLmax 0.8 V5
EN pin resistance to GND RENVEN = 1.5 Vmin 600 · typ 1500 · max 2400 kΩ5
EN pulldown current IENVEN = 1.5 Vtyp 1 uA5
VFB threshold voltage (1) VFBTHVO = 1.05 V, IO = 10 mA, Eco-mode operation; not production testedtyp 774 mV5
VFB threshold voltage VFBTHVO = 1.05 V, continuous mode operationmin 749 · typ 768 · max 787 mV5
VFB input current IVFBVFB = 0.8 Vtyp 0 · max 0.1 uA5
High-side switch resistance RDS(on)hTA = 25°C, VBST – SW = 5 Vtyp 140 mΩ5
Low-side switch resistance RDS(on)lTA = 25°Ctyp 84 mΩ5
Current limit IoclDC current, VOUT = 1.05 V, L1 = 2.2 uHmin 2.4 · typ 3.2 · max 4 A5
Thermal shutdown threshold(1) TSDNShutdown temperature; not production testedtyp 160 °C5
Thermal shutdown threshold(1) TSDNHysteresis; not production testedtyp 25 °C5
Minimum off time tOFF(MIN)VFB = 0.5 Vtyp 220 · max 310 ns5
Soft-start time tssInternal soft-start timetyp 1 ms5
Switching frequency FswVIN = 12 V, VO = 3.3 V, IO = 1 Atyp 580 kHz5
Output UVP threshold VUVPHiccup detect (H > L)typ 65 %5
Hiccup wait time THICCUP_WAITtyp 1.2 ms5
Hiccup time before restart THICCUP_REtyp 10 ms5
UVLO threshold UVLOWake up VIN voltagetyp 3.8 · max 4.3 V5
UVLO threshold UVLOShut down VIN voltagemin 3.3 · typ 3.4 V5
UVLO threshold UVLOHysteresis VIN voltagetyp 0.4 V5

Pins, by the datasheet

6
1 GND
Low-side power NFET source and controller ground; connect sensitive VFB ground at a single point. · p. 3
2 SW
Switch node connection between high-side NFET and low-side NFET. · p. 3
3 VIN
Input voltage supply and high-side power NFET drain. · p. 3
4 VFB
Converter feedback input; connect to output voltage through a feedback resistor divider. · p. 3
5 EN
Active-high enable input; must be pulled up to enable the device. · p. 3
6 VBST
High-side NFET gate-drive supply; connect a 0.1-uF capacitor between VBST and SW. · p. 3

Open-source boards using it

12See all 12
  • 2 layers80 × 50 mmGreaseweazle F7 Plus V2, the printed circuit board in 3D

    Greaseweazle F7 Plus V2

    aerobaticant/Greaseweazle-F7-Plus

    My board design for Keir Fraser's Greaseweazle

    66 parts30
  • 4 layers70 × 47.5 mmQSFP Breakout, the printed circuit board in 3D

    QSFP Breakout

    mwrnd/QSFP_Breakout

    QSFP Breakout to U.FL/UMCC

    54 parts6BSD-2-Clause
  • 4 layers80 × 100 mmIce40 breakout, the printed circuit board in 3D

    Ice40 breakout

    RubenVoell/iceduino

    The basic idea behind this project is to create a simple breakout of an ICE40 FPGA with some LEDs and Buttons to interact with the FPGA and enough resources to run a simple softcore, like a small RISC-V core.

    248 parts3
  • 4 layers70 × 70.5 mmPCB FINAL UPDATED, the printed circuit board in 3D

    PCB FINAL UPDATED

    bash227/ECG-Motor-Control-Power-Management-PCB

    A multi-function PCB integrating biomedical signal acquisition (ECG), DC motor control, and advanced power management for wearable applications.

    111 parts2MIT
  • 2 layers34 × 4 mmMoco, the printed circuit board in 3D

    Moco

    dstutman/moco

    A compact and cost effective BLDC servo controller.

    58 parts2
  • 2 layers18.9 × 21.9 mmTPS562201 DC DC converter, the printed circuit board in 3D

    TPS562201 DC DC converter

    Bobrowicz/TPS562201-DC-DC-Converter-Module

    2A step down voltage regulator PCB module

    13 parts
  • 2 layers65 × 25 mmAqm fan controller, the printed circuit board in 3D

    Aqm fan controller

    cehbz/aqm-fan-controller

    KiCad PCB design for a PWM fan controller (ESP32-C3, TPS562201 buck converter)

    32 parts
  • 4 layers205 × 75 mmPicoMIST, the printed circuit board in 3D

    PicoMIST

    JacobR3301/picomist_pcb

    52 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS562201DDC?

Yes. The symbol is Celestial_Power_Switchmode:TI TPS562201DDC and the footprint Package_TO_SOT_SMD:TSOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS562201DDC?

TSOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the TPS562201DDC datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS562201DDC?

JLCPCB lists it as part C90061, with 547,591 in stock; the sellers' links on this page open their listings.

What can replace the TPS562201DDC?

Parts like it in the library: the SX1308 by SX, the ETA8120S2G by etasolution, the LN2220PAR by NATLINEAR and the TPS54302DDC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS562201DDC?

12 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.