
THVD1420DRL
Texas InstrumentsExtended
-40℃~+125℃ 1 1 12Mbps 1uA 256 3V~5.5V Enable shutdown、Tx/Rx enable、Hot-swap protection Half-Duplex Transceiver ±16kV SOT-583 RS-485 / RS-422 ICs ROHS
- Part id
- ti/THVD1420DRL
- Category
- RS 485, RS 422 ICs
- Package
- SOT-583
- Pins
- 8
- In stock
- 30,366 at JLCPCB (C3235555)
- Used on
- 4 open-source boards
Overview
The THVD1420DRL is a RS 485, RS 422 IC made by Texas Instruments in a SOT-583 package with 8 pins. -40℃~+125℃ 1 1 12Mbps 1uA 256 3V~5.5V Enable shutdown、Tx/Rx enable、Hot-swap protection Half-Duplex Transceiver ±16kV SOT-583 RS-485 / RS-422 ICs ROHS.
PCBKit's library has its KiCad symbol (Interface_UART:THVD1420D, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 30,366 are in stock at JLCPCB (part C3235555). 4 open-source boards in 2 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
14- Supply, least
- 3 V · VCC, recommended operating min · p. 5
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 5
- Supply, absolute maximum
- 7 V · VCC, absolute max · p. 4
- Works from
- -40 °C · Operating ambient temperature min · p. 5
- Works up to
- 125 °C · Operating ambient temperature max · p. 5
- Junction, hottest
- 170 °C · Junction temperature absolute max · p. 4
- A pin gives at most
- 24 mA · Receiver output current absolute max magnitude · p. 4
- Takes working
- 1.5 mA · VCC = 3.6 V, driver and receiver enabled, no load, typical · p. 7
- Takes asleep
- 100 nA · VCC = 3.6 V or 5.5 V, driver and receiver disabled, no load, typical · p. 7
- Data rate, most
- 12 Mbit/s · THVD1420 signaling rate max · p. 5
- Edge
- 15 ns · Driver differential output rise and fall times, typical · p. 7
- Junction to air (DRL (SOT))
- 112.2 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to case (DRL (SOT))
- 28.4 K/W · Junction-to-case (top) thermal resistance · p. 5
- Junction to board (DRL (SOT))
- 22.1 K/W · Junction-to-board thermal resistance · p. 5
What it is and has
11- Interface
- Half-duplex RS-422/RS-485 · p. 1
- Data rate
- 12 Mbps · p. 1
- Bus I/O HBM ESD protection
- ±16 kV · p. 1
- Bus I/O IEC contact ESD protection
- ±12 kV · p. 1
- Bus I/O IEC air-gap ESD protection
- ±15 kV · p. 1
- Bus I/O fast transient burst protection
- ±4 kV · p. 1
- Receiver hysteresis
- Large receiver hysteresis for noise rejection · p. 1
- Hot plug-in capability
- Glitch-free power-up/down · p. 1
- Failsafe
- Open, short, and idle bus · p. 1
- Bus loading
- 1/8 unit load, up to 256 bus nodes · p. 1
- Package options
- SOIC-8 (D), SOT-8 (DRL) · p. 3
Around it
1- res matches the characteristic impedance, Z0, of the cable
- between A and B; Termination resistor RT at each cable end to eliminate line reflections. · p. 15
Specifications
66| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | Over operating free-air temperature range | min -0.5 · max 7 V | 4 |
| Input voltage at any logic pin (D, DE or RE) VL | Over operating free-air temperature range | min -0.3 · max 5.7 V | 4 |
| Voltage at A or B inputs VA, VB | Over operating free-air temperature range | min -16 · max 16 V | 4 |
| Receiver output current IO | Over operating free-air temperature range | min -24 · max 24 mA | 4 |
| Junction temperature TJ | max 170 °C | 4 | |
| Storage temperature TSTG | min -65 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; Bus terminals (A, B) and GND; ±16,000 V | min -16000 · max 16000 V | 4 |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; All other pins; ±4,000 V | min -4000 · max 4000 V | 4 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002; ±1,500 V | min -1500 · max 1500 V | 4 |
| Electrostatic discharge V(ESD) | IEC 61000-4-2 ESD (Contact Discharge), bus terminals and GND; ±12,000 V | min -12000 · max 12000 V | 4 |
| Electrostatic discharge V(ESD) | IEC 61000-4-2 ESD (Air-Gap Discharge), bus terminals and GND; ±15,000 V | min -15000 · max 15000 V | 4 |
| Electrostatic discharge V(ESD) | IEC 61000-4-4 EFT (Fast transient or burst), bus terminals and GND; ±4,000 V | min -4000 · max 4000 V | 4 |
| Supply voltage VCC | NOM column is 5 V | min 3 · typ 5 · max 5.5 V | 5 |
| Differential input voltage VID | min -12 · max 12 V | 5 | |
| Input voltage at any bus terminal VI | min -7 · max 12 V | 5 | |
| High-level input voltage (driver, driver-enable, and receiver-enable inputs) VIH | min 2 · max 5.5 V | 5 | |
| Low-level input voltage (driver, driver-enable, and receiver-enable inputs) VIL | min 0 · max 0.8 V | 5 | |
| Output current IO | Driver | min -60 · max 60 mA | 5 |
| Output current IO | Receiver | min -8 · max 8 mA | 5 |
| Differential load resistance RL | NOM column is 60 Ω | min 54 · typ 60 Ω | 5 |
| Signaling rate: THVD1420 1/tUI | THVD1420 | max 12 Mbps | 5 |
| Junction temperature TJ | min -40 · max 150 °C | 5 | |
| Operating ambient temperature TA | min -40 · max 125 °C | 5 | |
| Thermal shutdown threshold (temperature rising) TSHDN | NOM column is 170 °C | min 150 · typ 170 °C | 5 |
| Thermal shutdown hysteresis THYS | NOM column is 15 °C | typ 15 °C | 5 |
| Junction-to-ambient thermal resistance RθJA | DRL (SOT), 8 PINS; value column | typ 112.2 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | DRL (SOT), 8 PINS; value column | typ 28.4 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | DRL (SOT), 8 PINS; value column | typ 22.1 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | DRL (SOT), 8 PINS; value column | typ 1.2 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | DRL (SOT), 8 PINS; value column | typ 22 °C/W | 5 |
| Power dissipation, driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square-wave signal at maximum signaling rate (THVD1420) PD | THVD1420; Unterminated; RL = 300 Ω, CL = 50 pF; value column | typ 175 mW | 5 |
| Power dissipation, driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square-wave signal at maximum signaling rate (THVD1420) PD | THVD1420; RS-422 load; RL = 100 Ω, CL = 50 pF; value column | typ 200 mW | 5 |
| Power dissipation, driver and receiver enabled, VCC = 5.5 V, TA = 125°C, 50% duty cycle square-wave signal at maximum signaling rate (THVD1420) PD | THVD1420; RS-485 load; RL = 54 Ω, CL = 50 pF; value column | typ 250 mW | 5 |
| Driver differential-output voltage magnitude │VOD│ | RL = 60 Ω, -7 V ≤ Vtest ≤ 12 V; See Figure 6-1 | min 1.5 · typ 2 V | 6 |
| Driver differential-output voltage magnitude │VOD│ | RL = 60 Ω, -7 V ≤ Vtest ≤ 12 V, 4.5 V ≤ Vcc ≤ 5.5 V; See Figure 6-1 | min 2.1 · typ 3 V | 6 |
| Driver differential-output voltage magnitude │VOD│ | RL = 100 Ω, CL = 50 pF; See Figure 6-2 | min 2 · typ 2.5 V | 6 |
| Driver differential-output voltage magnitude │VOD│ | RL = 54 Ω, CL = 50 pF; See Figure 6-2 | min 1.5 · typ 2 V | 6 |
| Driver differential-output voltage magnitude │VOD│ | RL = 54 Ω, 4.5 V ≤ Vcc ≤ 5.5 V; See Figure 6-2 | min 2.1 · typ 3 V | 6 |
| Change in magnitude of driver differential-output voltage Δ│VOD│ | RL = 54 Ω or 100 Ω, CL = 50 pF; See Figure 6-2 | min -50 · max 50 mV | 6 |
| Steady-state common-mode output voltage VOC(SS) | RL = 54 Ω or 100 Ω, CL = 50 pF; See Figure 6-2; typical = VCC / 2 | min 1 · max 3 V | 6 |
| Change in differential driver common-mode output voltage ΔVOC | RL = 54 Ω or 100 Ω, CL = 50 pF; See Figure 6-2 | min -50 · max 50 mV | 6 |
| Peak-to-peak driver common-mode output voltage VOC(PP) | RL = 54 Ω, CL = 50 pF, VCC = 5 V; See Figure 6-2 | typ 520 mV | 6 |
| Peak-to-peak driver common-mode output voltage VOC(PP) | RL = 54 Ω, CL = 50 pF, VCC = 3.3 V; See Figure 6-2 | typ 250 mV | 6 |
| Driver short-circuit output current │IOS│ | DE = VCC, -7 V ≤ [VA or VB] ≤ 12 V, or A pin shorted to B pin | min -250 · max 250 mA | 6 |
| Bus input current (driver disabled) II | DE = 0 V, VCC = 0 V or 5.5 V; VI = 12 V | typ 75 · max 100 uA | 6 |
| Bus input current (driver disabled) II | DE = 0 V, VCC = 0 V or 5.5 V; VI = –7 V | min -97 · typ -70 uA | 6 |
| Positive-going receiver differential-input voltage threshold VIT+ | -7 V ≤ VCM ≤ 12 V | typ -70 · max -45 mV | 6 |
| Negative-going receiver differential-input voltage threshold VIT– | -7 V ≤ VCM ≤ 12 V | min -200 · typ -150 mV | 6 |
| Receiver differential-input voltage threshold hysteresis (VIT+ – VIT– ) VHYS | -7 V ≤ VCM ≤ 12 V | min 30 · typ 50 mV | 6 |
| Receiver low-level output voltage VOL | IOL = 4 mA | typ 0.2 · max 0.4 V | 6 |
| Receiver high-impedance output current IOZ | VO = 0 V or VCC, RE = VCC | min -1 · max 1 uA | 6 |
| Input current (D, DE, RE) IIN | min -5 · max 5 uA | 6 | |
| Supply current (quiescent) ICC | VCC = 3.6 V; Both driver and receiver enabled; DE = VCC, RE = 0, no load | typ 1500 · max 1800 uA | 7 |
| Supply current (quiescent) ICC | VCC = 3.6 V; Driver enabled and receiver disabled; DE = VCC, RE = VCC, no load | typ 1000 · max 1500 uA | 7 |
| Supply current (quiescent) ICC | VCC = 3.6 V; Driver disabled and receiver enabled; DE = 0, RE = 0, no load | typ 700 · max 900 uA | 7 |
| Supply current (quiescent) ICC | VCC = 3.6 V; Both driver and receiver disabled; DE = 0, RE = VCC, no load | typ 0.1 · max 1 uA | 7 |
| Supply current (quiescent) ICC | VCC = 5.5 V; Driver and receiver enabled; DE = VCC, RE = 0, no load | typ 1700 · max 3000 uA | 7 |
| Supply current (quiescent) ICC | VCC = 5.5 V; Driver enabled, receiver disabled; DE = VCC, RE = VCC, no load | typ 1300 · max 2500 uA | 7 |
| Supply current (quiescent) ICC | VCC = 5.5 V; Driver disabled, receiver enabled; DE = 0, RE = 0, no load | typ 800 · max 1000 uA | 7 |
| Supply current (quiescent) ICC | VCC = 5.5 V; Both driver and receiver disabled; DE = 0, RE = VCC, no load | typ 0.1 · max 1 uA | 7 |
| Driver differential output rise and fall times tr, tf | THVD1420; over operating free-air temperature range; See Figure 6-3 | typ 15 · max 25 ns | 7 |
| Driver propagation delay tPHL, tPLH | THVD1420; over operating free-air temperature range; See Figure 6-3 | typ 20 · max 38 ns | 7 |
| Driver pulse skew, |tPHL – tPLH| tSK(P) | THVD1420; over operating free-air temperature range; See Figure 6-3 | max 3.5 ns | 7 |
| Driver disable time tPHZ, tPLZ | THVD1420; over operating free-air temperature range; See Figure 6-4 and Figure 6-5 | typ 15 · max 38 ns | 7 |
| Driver enable time tPZH, tPZL | THVD1420; Receiver enabled; See Figure 6-4 and Figure 6-5 | typ 15 · max 70 ns | 7 |
| Driver enable time tPZH, tPZL | THVD1420; Receiver disabled; See Figure 6-4 and Figure 6-5 | typ 4 · max 10 us | 7 |
Pins, by the datasheet
8- 1 R
- Receive data output. · p. 3
- 2 RE
- Receiver enable, active low, with internal 2-MΩ pull-up. · p. 3
- 3 DE
- Driver enable, active high, with internal 2-MΩ pull-down. · p. 3
- 4 D
- Driver data input. · p. 3
- 5 GND
- Device ground. · p. 3
- 6 A
- Bus I/O port, A (complementary to B). · p. 3
- 7 B
- Bus I/O port, B (complementary to A). · p. 3
- 8 VCC
- 3.3-V to 5-V supply. · p. 3
Open-source boards using it
4Parts like it
8SP3485EN-L/TR
SOIC-8-40℃~+85℃ 1 1 10Mbps 2mA 3.3V 32 Half-Duplex Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsSP485EEN-L/TR
SOIC-8-40℃~+85℃ 1 1 10Mbps 4.75V~5.25V 900uA Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsSN75176BD
SOIC-80℃~+70℃ 1 1 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsMAX485ESA+T
SOIC-8-40℃~+85℃ 1 1 2.5Mbps 4.75V~5.25V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsMAX13487EESA+T
SOIC-8-40℃~+85℃ 1 1 128 4.5mA 4.75V~5.25V 500Kbps Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsTHVD2450D
SOIC-8-40℃~+125℃ 1 1 256 3V~5.5V 50Mbps Half-Duplex Transceiver ±16kV SOIC-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsTP8485E-SR
SOIC-8-40℃~+125℃ 1 1 1.4mA 250Kbps 256 3V~5.5V Transceiver ±18kV SOIC-8 RS-485 / RS-422 ICs ROHS3PEAKRS-485 / RS-422 ICsSP3078EEN-L/TR
SOIC-8-40℃~+85℃ 1 1 1.5mA 16Mbps 256 3.3V Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICs
Questions
Is there a KiCad symbol and footprint for the THVD1420DRL?
Yes. The symbol is Interface_UART:THVD1420D and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the THVD1420DRL?
SOT-583, with 8 pins. Its footprint is drawn on this page.
Where is the THVD1420DRL datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the THVD1420DRL?
JLCPCB lists it as part C3235555, with 30,366 in stock; the sellers' links on this page open their listings.
What can replace the THVD1420DRL?
Parts like it in the library: the SP3485EN-L/TR by MaxLinear, the SP485EEN-L/TR by MaxLinear, the SN75176BD by Texas Instruments and the MAX485ESA+T by Maxim Integrated (Analog Devices). Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the THVD1420DRL?
4 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.


