Skip to the content
1234567899999999

DRV8871DDA

Texas InstrumentsExtended

-40℃~+125℃ 1 10uA 3.6A 565mΩ PWM Yes SO-8-EP Brushed DC Motor Drivers ROHS

Part id
ti/DRV8871DDA
Category
Stepper Motor Driver
Package
SO-8-EP
Pins
9
In stock
3,470 at JLCPCB (C75864)
Used on
78 open-source boards

Overview

The DRV8871DDA is a stepper Motor Driver made by Texas Instruments in a SO-8-EP package with 9 pins. -40℃~+125℃ 1 10uA 3.6A 565mΩ PWM Yes SO-8-EP Brushed DC Motor Drivers ROHS.

PCBKit's library has its KiCad symbol (Driver_Motor:DRV8871DDA, from KiCad's library) and its footprint (Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias, from KiCad's library), ready for a KiCad board. 3,470 are in stock at JLCPCB (part C75864). 78 open-source boards in 70 repositories on GitHub use it.

Symbol

1GND2IN23IN14ILIM5VM6OUT18OUT2
Driver_Motor:DRV8871DDAFrom KiCad's library

Footprint

1234567899999999
Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalViasFrom KiCad's library

From the datasheet

12
Supply, least
6.5 V · VM, recommended operating min · p. 4
Supply, most
45 V · VM, recommended operating max · p. 4
Supply, absolute maximum
50 V · VM, absolute max · p. 3
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
125 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature absolute max · p. 3
Takes working
3 mA · VM operating supply current typical, VM = 12 V · p. 5
Takes asleep
10 µA · VM sleep current max, VM = 12 V · p. 5
Gives
3.5 A · Output current absolute max, 100% duty cycle · p. 3
Junction to air (DDA (HSOP))
41.1 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to board (DDA (HSOP))
23.1 K/W · Junction-to-board thermal resistance · p. 4
Junction to case (DDA (HSOP))
53.1 K/W · Junction-to-case top thermal resistance · p. 4

What it is and has

10
Driver
H-bridge motor driver · p. 1
Peak output current
3.6 A · p. 1
Control interface
PWM · p. 1
Current regulation
No external sense resistor required · p. 1
Sleep mode
Low power · p. 1
Package
8-pin HSOP with PowerPAD · p. 1
Protection
VM undervoltage lockout · p. 1
Protection
Overcurrent protection · p. 1
Protection
Thermal shutdown · p. 1
Fault recovery
Automatic · p. 1

Around it

3
cap 0.1 µF
between VM and GND; Bypass capacitor; use ceramic and place close to the device pins; rate for VM. · p. 3
cap 47 µF
between VM and GND; Bulk capacitor in the typical application; place to minimize the high-current path through the driver. · p. 11
res 30 kΩ
between ILIM and GND; Typical application current-limit resistor; example motor current trip point is 2.1 A. · p. 11

Specifications

46
ParameterConditionsAs printedPage
Power supply voltage (VM)Over operating free-air temperature rangemin -0.3 · max 50 V3
Logic input voltage (IN1, IN2)Over operating free-air temperature rangemin -0.3 · max 7 V3
Continuous phase node pin voltage (OUT1, OUT2)Over operating free-air temperature range; maximum is VM + 0.7 Vmin -0.7 V3
Output current (100% duty cycle)Over operating free-air temperature rangemin 0 · max 3.5 A3
Operating junction temperature, TJ TJmin -40 · max 150 °C3
Storage temperature, Tstg Tstgmin -65 · max 150 °C3
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; rated value ±6000 Vmax 6000 V3
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; rated value ±750 Vmax 750 V3
Power supply voltage VMOver operating free-air temperature rangemin 6.5 · max 45 V4
Logic input voltage (IN1, IN2) VIOver operating free-air temperature rangemin 0 · max 5.5 V4
Logic input PWM frequency (IN1, IN2) fPWMInput pulse width at least 800 ns; at 200 kHz usable duty cycle is 16% to 84%min 0 · max 200 kHz4
Peak output current IpeakPower dissipation and thermal limits must be observedmin 0 · max 3.6 A4
Operating ambient temperature TAPower dissipation and thermal limits must be observedmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADRV8871, DDA (HSOP), 8 PINStyp 41.1 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DRV8871, DDA (HSOP), 8 PINStyp 53.1 °C/W4
Junction-to-board thermal resistance RθJBDRV8871, DDA (HSOP), 8 PINStyp 23.1 °C/W4
Junction-to-top characterization parameter ψJTDRV8871, DDA (HSOP), 8 PINStyp 8.2 °C/W4
Junction-to-board characterization parameter ψJBDRV8871, DDA (HSOP), 8 PINStyp 23 °C/W4
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV8871, DDA (HSOP), 8 PINStyp 2.7 °C/W4
VM operating voltage VMTA = 25°C, over recommended operating conditionsmin 6.5 · max 45 V5
VM operating supply current IVMTA = 25°C, VM = 12 Vtyp 3 · max 10 mA5
VM sleep current IVMSLEEPTA = 25°C, VM = 12 Vmax 10 uA5
Turn-on time tONTA = 25°C, VM > VUVLO with IN1 or IN2 high; initial power-up or exit from sleeptyp 40 · max 50 us5
Input logic low voltage VILTA = 25°C, over recommended operating conditionsmax 0.5 V5
Input logic high voltage VIHTA = 25°C, over recommended operating conditionsmin 1.5 V5
Input logic hysteresis VHYSTA = 25°C, over recommended operating conditionstyp 0.5 V5
Input logic low current IILTA = 25°C, VIN = 0 Vmin -1 · max 1 uA5
Input logic high current IIHTA = 25°C, VIN = 3.3 Vtyp 33 · max 100 uA5
Pulldown resistance RPDTA = 25°C, To GNDtyp 100 kΩ5
Propagation delay tPDTA = 25°C, INx to OUTx change (see Figure 6)typ 0.7 · max 1 us5
Time to sleep tsleepTA = 25°C, Inputs low to sleeptyp 1 · max 1.5 ms5
High-side FET on resistance RDS(ON)TA = 25°C, VM = 24 V, I = 1 A, fPWM = 25 kHztyp 307 · max 360 mΩ5
Low-side FET on resistance RDS(ON)TA = 25°C, VM = 24 V, I = 1 A, fPWM = 25 kHztyp 258 · max 320 mΩ5
Output dead time tDEADTA = 25°C, over recommended operating conditionstyp 220 ns5
Body diode forward voltage VdTA = 25°C, IOUT = 1 Atyp 0.8 · max 1 V5
Constant for calculating current regulation (see Equation 1) VILIMTA = 25°C, IOUT = 1 Amin 59 · typ 64 · max 69 kV5
PWM off-time tOFFTA = 25°C, over recommended operating conditionstyp 25 us5
PWM blanking time tBLANKTA = 25°C, over recommended operating conditionstyp 2 us5
VM undervoltage lockout VUVLOTA = 25°C, VM falls until UVLO triggerstyp 6.1 · max 6.4 V5
VM undervoltage lockout VUVLOTA = 25°C, VM rises until operation recoverstyp 6.3 · max 6.5 V5
VM undervoltage hysteresis VUV,HYSTA = 25°C, Rising to falling thresholdmin 100 · typ 180 mV5
Overcurrent protection trip level IOCPTA = 25°C, over recommended operating conditionsmin 3.7 · typ 4.5 · max 6.4 A5
Overcurrent deglitch time tOCPTA = 25°C, over recommended operating conditionstyp 1.5 us5
Overcurrent retry time tRETRYTA = 25°C, over recommended operating conditionstyp 3 ms5
Thermal shutdown temperature TSDTA = 25°C, over recommended operating conditionsmin 150 · typ 175 °C5
Thermal shutdown hysteresis THYSTA = 25°C, over recommended operating conditionstyp 40 °C5

Pins, by the datasheet

9
1 GND
Logic ground; connect to board ground. · p. 3
2 IN2
Logic input controlling the H-bridge output; has an internal pulldown. · p. 3
3 IN1
Logic input controlling the H-bridge output; has an internal pulldown. · p. 3
4 ILIM
Current limit control; connect a resistor to ground to set the current chopping threshold. · p. 3
5 VM
6.5-V to 45-V power supply; connect a 0.1-uF bypass capacitor and sufficient bulk capacitance to ground, rated for VM. · p. 3
6 OUT1
H-bridge output; connect directly to the motor or other inductive load. · p. 3
7 PGND
High-current ground path; connect to board ground. · p. 3
8 OUT2
H-bridge output; connect directly to the motor or other inductive load. · p. 3
— PAD
Thermal pad; connect to board ground using large ground planes on multiple layers and multiple nearby vias. · p. 3

Ordering codes, by the datasheet

2
DRV8871DDA
SO PowerPAD, DDA, 8 pins · Package quantity 75; operating temperature -40 to 125 °C · p. 18
DRV8871DDAR
SO PowerPAD, DDA, 8 pins · Package quantity 2500; operating temperature -40 to 125 °C · p. 18

Open-source boards using it

78See all 78
  • 4 layers122.2 × 115.1 mmScan controller kicad, the printed circuit board in 3D

    Scan controller kicad

    fwachsmuth/Filmkorn-Raw-Scanner

    The Filmkorn Raw Scanner, turning 8mm and 16mm films into lossless 12-bit CinemaDNG

    170 parts13MIT
  • 4 layers81.3 × 52.8 mmGlue Board, the printed circuit board in 3D

    Glue Board

    arkorobotics/robocar-pinky

    DIY Robocar Project - Codename Pinky

    87 parts12
  • 2 layers65.6 × 56 mmWw2020, the printed circuit board in 3D

    Ww2020

    dkjonas/WildWillyHardware

    69 parts11
  • 4 layers50 × 50 mmSimpleboard, the printed circuit board in 3D

    Simpleboard

    AlessioMorale/unav2_hardware

    Initial test hardware for the future uNav board version

    122 parts5MIT
  • 2 layers83.3 × 56.5 mmPhone bell, the printed circuit board in 3D

    Phone bell

    purduehackers/phone-bell

    A Rotary Phone Doorbell

    53 parts4
  • 4 layers123 × 56 mmSkyduino Hardware, the printed circuit board in 3D

    Skyduino Hardware

    Skyduino/Skyduino-Hardware

    Hardware design files for the Skyduino roaster

    80 parts4
  • 4 layers31.3 × 34 mmNOGGIN, the printed circuit board in 3D

    NOGGIN

    berkeleyauv/RoboSub_HW

    PCB designs for Underwater Robotics at Berkeley (UR@B)

    60 parts3GPL-3.0
  • 2 layers93.1 × 158.3 mmMegaMouse, the printed circuit board in 3D

    MegaMouse

    KenwoodFox/MegaMouse

    MegaMouse! An atmega 328p powered micromouse!

    136 parts3MIT

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the DRV8871DDA?

Yes. The symbol is Driver_Motor:DRV8871DDA and the footprint Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8871DDA?

SO-8-EP, with 9 pins. Its footprint is drawn on this page.

Where is the DRV8871DDA datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8871DDA?

JLCPCB lists it as part C75864, with 3,470 in stock; the sellers' links on this page open their listings.

What can replace the DRV8871DDA?

Parts like it in the library: the DRV8870DDA by Texas Instruments and the DRV8872DDAR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV8871DDA?

78 boards in 70 repositories on GitHub; the most starred are listed on this page, with their KiCad files.