
BQ24072RGTR
Texas InstrumentsExtended
-40℃~+125℃ 1 1.5A 1.5mA 4.2V 4.35V~6.6V Charging IC Lithium Battery Support QFN-16-EP(3x3) Battery Management ROHS
- Part id
- ti/BQ24072RGTR
- Category
- Battery Management
- Package
- QFN-16-EP(3x3)
- Pins
- 17
- In stock
- 2,424 at JLCPCB (C140288)
- Used on
- 30 open-source boards
Overview
The BQ24072RGTR is a battery Management made by Texas Instruments in a QFN-16-EP(3x3) package with 17 pins. -40℃~+125℃ 1 1.5A 1.5mA 4.2V 4.35V~6.6V Charging IC Lithium Battery Support QFN-16-EP(3x3) Battery Management ROHS.
PCBKit's library has its KiCad symbol (Battery_Management:BQ24072RGT, from KiCad's library) and its footprint (Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm, from KiCad's library), ready for a KiCad board. 2,424 are in stock at JLCPCB (part C140288). 30 open-source boards in 27 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
17- Supply, least
- 4.35 V · IN, recommended operating min, BQ24072 · p. 10
- Supply, most
- 6.4 V · IN, recommended operating max, BQ24072 · p. 10
- Supply, absolute maximum
- 28 V · IN, absolute maximum relative to VSS · p. 10
- Junction, hottest
- 150 °C · Junction temperature, absolute max · p. 10
- Takes working
- 1.1 mA · IN, typical active supply current, VIN = 6 V, no OUT load · p. 12
- Takes asleep
- 4.3 µA · BAT, typical sleep current, no input power, TJ = 85°C · p. 12
- Takes asleep
- 41.3 µA · IN, typical standby current, EN1 = EN2 = HI, VIN = 6 V, TJ = 85°C · p. 12
- Takes asleep
- 99.8 µA · IN, typical standby current, EN1 = EN2 = HI, VIN = 10 V, TJ = 85°C · p. 12
- Gives
- 1.5 A · BAT charging current, recommended max · p. 10
- Gives
- 4.5 A · OUT current, recommended max · p. 10
- A pin gives at most
- 15 mA · CHG or PGOOD sink current, absolute max · p. 10
- Output
- 4.2 V · BAT, typical battery charge regulation voltage · p. 13
- Dropout
- 300 mV · IN to OUT, typical at IIN = 1 A, VIN = 4.3 V, VBAT = 4.2 V · p. 12
- Dropout
- 50 mV · BAT to OUT, typical at IOUT = 1 A, VIN = 0 V, VBAT > 3 V · p. 12
- Junction to air (RGT)
- 44.5 K/W · Junction-to-ambient thermal resistance · p. 11
- Junction to board (RGT)
- 17.2 K/W · Junction-to-board thermal resistance · p. 11
- Junction to case (RGT)
- 54.2 K/W · Junction-to-case top thermal resistance · p. 11
What it is and has
7- Charger
- Standalone 1-cell, 1.5-A linear battery charger with power path · p. 1
- USB
- Fully compliant USB charger · p. 1
- System output
- Tracks battery voltage · p. 1
- Protection
- 28-V input rating with overvoltage protection · p. 1
- Certification
- IEC 62368-1 · p. 1
- USB compliance
- Fully compliant USB charger · p. 1
- USB charging
- Fully compliant USB charger · p. 1
Around it
18- cap 4.7-μF to 47-μF
- between BAT and VSS; Ceramic battery bypass capacitor. · p. 8
- cap 1 μF to 10 μF
- between IN and VSS; Input bypass capacitor. · p. 8
- cap 4.7-μF to 47-μF
- between OUT and VSS; Ceramic system output bypass capacitor. · p. 8
- res 1kΩ-100kΩ
- between CHG and desired logic voltage rail; Charging status pull-up; an LED is an alternative. · p. 8
- res 1-kΩ to 100-kΩ
- between PGOOD and desired logic voltage rail; Power-good status pull-up; an LED is an alternative. · p. 8
- res 1100-Ω to 8-kΩ
- between ILIM and VSS; Programs maximum input current when EN2=1 and EN1=0. · p. 8
- res 590-Ω to 8.9-kΩ
- between ISET and VSS; Programs fast charge current; use 1% tolerance. · p. 8
- res 18-kΩ to 72-kΩ
- between TMR and VSS; Programs safety timer duration; grounding TMR disables timers and leaving it unconnected selects defaults. · p. 9
- res 10-kΩ
- between TS and VSS; Fixed resistor for applications that do not use the TS function. · p. 9
- other 10kΩ NTC thermistor
- between TS and VSS; Battery-pack temperature sensing. · p. 9
- res 1.1 kΩ to 8 kΩ
- between ILIM and VSS; Programs the input current limit, adjustable up to 1.5 A. · p. 21
- res 1.13 kΩ
- between ISET and VSS; Example programming resistor for approximately 800 mA fast charge current. · p. 34
- res 1.18 kΩ
- between ILIM and VSS; Example programming resistor for a 1.3 A input current limit. · p. 34
- res 46.4 kΩ
- between TMR and VSS; Example programming resistor for a 6.25-hour fast-charge safety timer. · p. 34
- res 10-kΩ
- between TS and VSS; Use when battery temperature monitoring is not required. · p. 35
- res 1.5-kΩ
- between OUT and CHG; Connect in series with an LED to indicate charging status. · p. 35
- res 1.5-kΩ
- between OUT and PGOOD; Connect in series with an LED to indicate a valid input source. · p. 35
- res on the order of 100 kΩ
- between processor power rail and CHG; Pullup for processor monitoring. · p. 35
Specifications
83| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input Voltage VI | IN (with respect to VSS) | min -0.3 · max 28 V | 10 |
| Input Voltage VI | BAT (with respect to VSS) | min -0.3 · max 5 V | 10 |
| Input Voltage VI | OUT, EN1, EN2, CE, TS, ISET, PGOOD, CHG, ILIM, TMR, ITERM, SYSOFF, TD (with respect to VSS) | min -0.3 · max 7 V | 10 |
| Input Current II | IN | max 1.6 A | 10 |
| Output Current (Continuous) IO | OUT | max 5 A | 10 |
| Output Current (Continuous) IO | BAT (Discharge mode) | max 5 A | 10 |
| Output Current (Continuous) IO | BAT (Charging mode); footnote (2) applies | max 1.5 A | 10 |
| Output Sink Current | CHG, PGOOD | max 15 mA | 10 |
| Junction temperature TJ | min -40 · max 150 °C | 10 | |
| Storage temperature Tstg | min -65 · max 150 °C | 10 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V | max 2000 V | 10 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 V | max 500 V | 10 |
| IN voltage range VI | min 4.35 · max 26 V | 10 | |
| IN operating voltage range VI | BQ24072 | min 4.35 · max 6.4 V | 10 |
| Input current, IN pin IIN | max 1.5 A | 10 | |
| Current, OUT pin IOUT | max 4.5 A | 10 | |
| Current, BAT pin (Discharging) IBAT | max 4.5 A | 10 | |
| Current, BAT pin (Charging) ICHG | Footnote (2) applies | max 1.5 A | 10 |
| Junction Temperature TJ | min -40 · max 125 °C | 10 | |
| Maximum input current programming resistor RILIM | min 1100 · max 8000 Ω | 10 | |
| Fast-charge current programming resistor RISET | Use a 1% tolerance resistor | min 590 · max 8900 Ω | 10 |
| Termination current programming resistor RITERM | min 0 · max 15 kΩ | 10 | |
| Timer programming resistor RTMR | min 18 · max 72 kΩ | 10 | |
| Junction-to-ambient thermal resistance RθJA | RGT, 16 PINS | typ 44.5 °C/W | 11 |
| Junction-to-case (top) thermal resistance RθJC(top) | RGT, 16 PINS | typ 54.2 °C/W | 11 |
| Junction-to-board thermal resistance RθJB | RGT, 16 PINS | typ 17.2 °C/W | 11 |
| Junction-to-top characterization parameter ψJT | RGT, 16 PINS | typ 1 °C/W | 11 |
| Junction-to-board characterization parameter ψJB | RGT, 16 PINS | typ 17.1 °C/W | 11 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | RGT, 16 PINS | typ 3.8 °C/W | 11 |
| Undervoltage lock-out UVLO | VIN: 0 V → 4 V | min 3.2 · typ 3.3 · max 3.4 V | 12 |
| Hysteresis on UVLO Vhys | VIN: 4 V → 0 V | min 200 · max 300 mV | 12 |
| Input power detection threshold VIN(DT) | Input power detected when VIN > VBAT + VIN(DT); VBAT = 3.6 V, VIN: 3.5 V → 4 V | min 55 · typ 80 · max 130 mV | 12 |
| Hysteresis on VIN(DT) Vhys | VBAT = 3.6 V, VIN: 4 V → 3.5 V | min 20 mV | 12 |
| Deglitch time, input power detected status tDGL(PGOOD) | Time measured from VIN: 0 V → 5 V 1 us rise-time to PGOOD = LO | typ 1.2 ms | 12 |
| Input overvoltage protection threshold VOVP | BQ24072; VIN: 5 V → 7 V | min 6.4 · typ 6.6 · max 6.8 V | 12 |
| Hysteresis on OVP Vhys | BQ24072; VIN: 7 V → 5V | typ 110 mV | 12 |
| Input overvoltage blanking time (OVP fault deglitch) tDGL(OVP) | typ 50 us | 12 | |
| Input overvoltage recovery time tREC | Time measured from VIN: 11 V → 5 V with 1 us fall-time to PGOOD = LO | typ 1.2 ms | 12 |
| Current source ISC | ILIM, ISET short-circuit detection, checked during startup; VIN > UVLO and VIN > VBAT + VIN(DT) | typ 1.3 mA | 12 |
| VSC VSC | ILIM, ISET short-circuit detection, checked during startup; VIN > UVLO and VIN > VBAT + VIN(DT) | typ 520 mV | 12 |
| Sleep current into BAT pin IBAT(PDWN) | CE = LO or HI, input power not detected, no load on OUT pin, TJ = 85°C | typ 4.3 · max 6.5 uA | 12 |
| Standby current into IN pin IIN | EN1= HI, EN2=HI, VIN = 6 V, TJ= 85°C | typ 41.3 · max 50 uA | 12 |
| Standby current into IN pin IIN | EN1= HI, EN2=HI, VIN = 10 V, TJ= 85°C | typ 99.8 · max 200 uA | 12 |
| Active supply current, IN pin ICC | CE = LO, VIN = 6 V, no load on OUT pin, VBAT > VBAT(REG), (EN1, EN2) ≠ (HI, HI) | typ 1.1 · max 1.5 mA | 12 |
| VIN – VOUT VDO(IN-OUT) | VIN = 4.3 V, IIN = 1 A, VBAT = 4.2 V | typ 300 · max 475 mV | 12 |
| VBAT – VOUT VDO(BAT-OUT) | IOUT = 1 A, VIN = 0 V, VBAT > 3 V | typ 50 · max 100 mV | 12 |
| OUT pin voltage regulation (BQ24072) VO(REG) | VIN > VOUT + VDO(IN-OUT), VBAT < 3.2 V | min 3.3 · typ 3.4 · max 3.5 V | 12 |
| Maximum input current IINmax | EN1 = LO, EN2 = LO | min 90 · typ 95 · max 100 mA | 12 |
| Maximum input current IINmax | EN1 = HI, EN2 = LO | min 450 · typ 475 · max 500 mA | 12 |
| Maximum input current factor KILIM | ILIM = 500 mA to 1.5 A | min 1500 · typ 1610 · max 1720 AΩ | 12 |
| Maximum input current factor KILIM | ILIM = 200 mA to 500 mA | min 1330 · typ 1525 · max 1720 AΩ | 12 |
| Programmable input current limit range IINmax | EN2 = HI, EN1 = LO, RILIM = 8 kΩ to 1.1 kΩ | min 200 · max 1500 mA | 12 |
| Input voltage threshold when input current is reduced VIN-DPM | EN2 = LO, EN1 = X | min 4.35 · typ 4.5 · max 4.63 V | 12 |
| Source current for BAT pin short-circuit detection IBAT | VBAT = 1.5 V | min 4 · typ 7.5 · max 11 mA | 13 |
| BAT pin short-circuit detection threshold VBAT(SC) | VBAT rising | min 1.6 · typ 1.8 · max 2 V | 13 |
| Battery charge voltage VBAT(REG) | BQ24072 | min 4.16 · typ 4.2 · max 4.23 V | 13 |
| Pre-charge to fast-charge transition threshold VLOWV | VIN > VUVLO and VIN > VBAT + VIN(DT) | min 2.9 · typ 3 · max 3.1 V | 13 |
| Deglitch time on pre-charge to fast-charge transition tDGL1(LOWV) | typ 25 ms | 13 | |
| Deglitch time on fast-charge to pre-charge transition tDGL2(LOWV) | typ 25 ms | 13 | |
| Battery fast charge current range ICHG | VBAT(REG) > VBAT > VLOWV, VIN = 5 V CE = LO, EN1 = LO, EN2 = HI | min 100 · max 1500 mA | 13 |
| Fast charge current factor KISET | min 797 · typ 890 · max 975 AΩ | 13 | |
| Pre-charge current factor KPRECHG | min 70 · typ 88 · max 106 AΩ | 13 | |
| Current for external termination-setting resistor IBIAS(ITERM) | VIN > VUVLO and VIN > VBAT + VIN(DT) | min 72 · typ 75 · max 78 uA | 13 |
| Deglitch time, termination detected tDGL(TERM) | typ 25 ms | 13 | |
| Deglitch time, recharge threshold detected tDGL(RCH) | typ 62.5 ms | 13 | |
| Delay time, input power loss to OUT LDO turn-off tDGL(NO-IN) | VBAT = 3.6 V. Time measured from VIN: 5 V → 3 V 1 us fall-time | typ 20 ms | 13 |
| Sink current for battery detection IBAT(DET) | VBAT = 2.5 V | min 5 · typ 7.5 · max 10 mA | 13 |
| Battery detection timer tDET | BAT high or low | typ 250 ms | 13 |
| Pre-charge safety timer value tPRECHG | TMR = floating | min 1440 · typ 1800 · max 2160 s | 13 |
| Charge safety timer value tMAXCHG | TMR = floating | min 14400 · typ 18000 · max 21600 s | 13 |
| Timer factor KTMR | min 36 · typ 48 · max 60 s/kΩ | 13 | |
| NTC bias current INTC | VIN > UVLO and VIN > VBAT + VIN(DT) | min 72 · typ 75 · max 78 uA | 13 |
| High temperature trip point VHOT | Battery charging, VTS Falling | min 270 · typ 300 · max 330 mV | 13 |
| Hysteresis on high trip point VHYS(HOT) | Battery charging, VTS Rising from VHOT | typ 30 mV | 13 |
| Logic LOW input voltage VIL | EN1, EN2, CE, SYSOFF, TD | min 0 · max 0.4 V | 14 |
| Logic HIGH input voltage VIH | EN1, EN2, CE, SYSOFF, TD | min 1.4 · max 6 V | 14 |
| Input sink current IIL | EN1, EN2, CE, SYSOFF, TD; VIL= 0 V | max 1 uA | 14 |
| Input source current IIH | EN1, EN2, CE, SYSOFF, TD; VIH= 1.4 V | max 10 uA | 14 |
| Output LOW voltage VOL | PGOOD, CHG; ISINK = 5 mA | max 0.4 V | 14 |
| Logic LOW input voltage VIL | EN1, EN2, CE | min 0 · max 0.4 V | 14 |
| Logic HIGH input voltage VIH | EN1, EN2, CE | min 1.4 · max 6 V | 14 |
| Input sink current IIL | EN1, EN2, CE; VIL= 0 V | max 1 uA | 14 |
| Input source current IIH | EN1, EN2, CE; VIH= 1.4 V | max 10 uA | 14 |
Pins, by the datasheet
16- 1 TS
- Battery-pack 10kΩ NTC thermistor input; connect a 10-kΩ resistor to VSS when unused. · p. 9
- 2 BAT
- Charger power stage output and battery voltage sense input; connect to battery positive and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
- 3 BAT
- Charger power stage output and battery voltage sense input; connect to battery positive and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
- 4 CE
- Active-low charge enable; high disables charging while OUT and battery supplement remain active; do not leave unconnected. · p. 8
- 5 EN2
- Input current limit configuration input used with EN1; internally pulled down; do not leave unconnected. · p. 8
- 6 EN1
- Input current limit configuration input used with EN2; internally pulled down; do not leave unconnected. · p. 8
- 7 PGOOD
- Pulls to VSS when a valid input source is detected; connect through a 1-kΩ to 100-kΩ resistor to the desired logic rail or use an LED. · p. 8
- 8 VSS
- Ground; connect to the thermal pad and circuit ground rail. · p. 9
- 9 CHG
- Pulls to VSS while charging and is high impedance when charging is complete or disabled; use a pull-up resistor or LED. · p. 8
- 10 OUT
- System supply output; connect to the system load and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
- 11 OUT
- System supply output; connect to the system load and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
- 12 ILIM
- Connect a 1100-Ω to 8-kΩ resistor to VSS to program maximum input current when EN2=1 and EN1=0; leaving unconnected disables charging. · p. 8
- 13 IN
- External DC supply input from an AC adapter or USB port; bypass to VSS with 1 uF to 10 uF. · p. 8
- 14 TMR
- Safety timer programming input; connect to VSS to disable timers, use an 18-kΩ to 72-kΩ resistor to program them, or leave unconnected for defaults. · p. 9
- 15 TD
- Termination disable input sampled only at startup; high disables termination and VSS enables it; do not leave unconnected. · p. 9
- 16 ISET
- Connect a 590-Ω to 8.9-kΩ resistor to VSS to program fast charge current; voltage monitors charge current and leaving unconnected disables charging. · p. 8
- 2 layers21.2 × 51.6 mm

- 4 layers108.7 × 55.1 mm

- 2 layers144.9 × 59.8 mm

Monkeys
PacketChat/MonkeyBadge
This repository contains the hardware design files, badge code, and backend infrastructure code for the HushCon Winter 2023 badge.
153 parts21 - 4 layers51 × 44 mm

- 2 layers21.2 × 57.2 mm

EnvPico nRF52840
Envious-Data/EnvPico-nRF52840
a nRF52840 MCU board in the form of a raspberry pi pico.
45 parts6Apache-2.0 - 4 layers39.6 × 49.6 mm

MS88SF3-ms keyboard
vsnrain/ms-keyboard
Custom Microsoft Sculpt compatible board replacement using MS88SF3 NRF52840 microcontroller.
69 parts2 - 4 layers58.5 × 26.5 mm

- 4 layers98.5 × 193.5 mm

Parts like it
7BQ24075RGT
QFN-16-EP(3x3)-40℃~+125℃ 1.5A 4.2V 4.35V~6.4V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24073RGTR
QFN-16-EP(3x3)-40℃~+125℃ 1.5A 4.2V 4.35V~6.4V 50uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24074RGTT
VQFN-16-EP(3x3)-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.5V 6.5uA Charging IC Lithium Battery Support Support VQFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24074RGTR
QFN-16-EP(3x3)-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.2V 6.5uA Charging IC Lithium Battery Not supported Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24079RGT
QFN-16-EP(3x3)-40℃~+125℃ 1.5A 4.1V 4.35V~6.6V 6.5uA Charging IC Lithium Battery Support QFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24074RGTRG4
VQFN-16(3x3)-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.5V 6.5uA Charging IC Lithium Battery Support Support VQFN-16(3x3) Battery Management ROHSTexas InstrumentsBattery ManagementBQ24073RGTT
VQFN-16-EP(3x3)-40℃~+85℃ 1 1.5A 4.2V 4.35V~6.4V 6.5uA Charging IC Lithium Battery Support Support VQFN-16-EP(3x3) Battery Management ROHSTexas InstrumentsBattery Management
Questions
Is there a KiCad symbol and footprint for the BQ24072RGTR?
Yes. The symbol is Battery_Management:BQ24072RGT and the footprint Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the BQ24072RGTR?
QFN-16-EP(3x3), with 17 pins. Its footprint is drawn on this page.
Where is the BQ24072RGTR datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the BQ24072RGTR?
JLCPCB lists it as part C140288, with 2,424 in stock; the sellers' links on this page open their listings.
What can replace the BQ24072RGTR?
Parts like it in the library: the BQ24075RGT by Texas Instruments, the BQ24073RGTR by Texas Instruments, the BQ24074RGTT by Texas Instruments and the BQ24074RGTR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the BQ24072RGTR?
30 boards in 27 repositories on GitHub; the most starred are listed on this page, with their KiCad files.