Skip to the content
17

BQ24074RGTT

Texas InstrumentsExtended

-40℃~+125℃ 1 1.5A 4.2V 4.35V~10.5V 6.5uA Charging IC Lithium Battery Support Support VQFN-16-EP(3x3) Battery Management ROHS

Part id
ti/BQ24074RGTT
Category
Battery Management
Package
VQFN-16-EP(3x3)
Pins
17
In stock
168 at JLCPCB (C2861252)
Used on
6 open-source boards

Overview

The BQ24074RGTT is a battery Management made by Texas Instruments in a VQFN-16-EP(3x3) package with 17 pins. -40℃~+125℃ 1 1.5A 4.2V 4.35V~10.5V 6.5uA Charging IC Lithium Battery Support Support VQFN-16-EP(3x3) Battery Management ROHS.

PCBKit's library has its KiCad symbol (Battery_Management:BQ24074RGT, from KiCad's library) and its footprint (Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm, from KiCad's library), ready for a KiCad board. 168 are in stock at JLCPCB (part C2861252). 6 open-source boards in 5 repositories on GitHub use it.

Symbol

1TS2BAT4CE5EN26EN17PGOOD8VSS9CHG10OUT12ILIM13IN14TMR15ITERM16ISET
Battery_Management:BQ24074RGTFrom KiCad's library

Footprint

17
Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mmFrom KiCad's library

From the datasheet

18
Supply, least
4.35 V · IN, recommended operating min · p. 10
Supply, most
10.2 V · IN, recommended operating max · p. 10
Supply, absolute maximum
28 V · IN, absolute maximum · p. 10
Junction, hottest
150 °C · Junction temperature absolute maximum · p. 10
Takes working
1.1 mA · IN, active supply current typical, charging enabled, no OUT load · p. 12
Takes asleep
4.3 µA · BAT sleep current typical, no OUT load, TJ = 85°C · p. 12
Takes asleep
41.3 µA · IN standby current typical, VIN = 6 V, TJ = 85°C · p. 12
Takes asleep
99.8 µA · IN standby current typical, VIN = 10 V, TJ = 85°C · p. 12
Gives
4.5 A · OUT current recommended max · p. 10
Gives
1.5 A · BAT charging current max; charging life reduced at 125°C · p. 10
A pin gives at most
15 mA · CHG or PGOOD sink current absolute maximum · p. 10
Output
4.4 V · OUT regulation typical, VIN > VOUT + VDO(IN-OUT) · p. 12
Dropout
300 mV · IN to OUT typical, IIN = 1 A, VIN = 4.3 V, VBAT = 4.2 V · p. 12
Dropout
50 mV · BAT to OUT typical, IOUT = 1 A, VIN = 0 V, VBAT > 3 V · p. 12
Junction to air (RGT)
44.5 K/W · Junction-to-ambient thermal resistance · p. 11
Junction to case (RGT)
54.2 K/W · Junction-to-case top thermal resistance · p. 11
Junction to board (RGT)
17.2 K/W · Junction-to-board thermal resistance · p. 11
Output
4.2 V · BAT, typical battery charge voltage · p. 13

What it is and has

12
Input voltage rating
28V, with overvoltage protection · p. 1
Programmable input current limit
Up to 1.5A for wall adapters · p. 1
Termination current
Programmable · p. 1
Safety timers
Programmable precharge and fast charge timers · p. 1
Protection
Reverse current, short circuit and thermal protection · p. 1
Temperature monitoring
NTC thermistor input · p. 1
Status indications
Charging, charge complete and power good · p. 1
Charger
Standalone single-cell 1.5 A linear battery charger with power path · p. 1
USB compliance
USB charger compliant · p. 1
Functional safety
BQ24074 functional safety support · p. 1
Protection
28 V input rating with overvoltage protection · p. 1
Package
VQFN (16), 3.00 mm × 3.00 mm · p. 1

Around it

11
cap 4.7-μF to 47-μF
between BAT and VSS; Ceramic bypass capacitor. · p. 8
cap 4.7-μF to 47-μF
between OUT and VSS; Ceramic bypass capacitor. · p. 8
cap 1 μF to 10 μF
between IN and VSS; Input bypass capacitor. · p. 8
res 1100-Ω to 8-kΩ
between ILIM and VSS; Programs maximum input current when EN2=1 and EN1=0. · p. 8
res 590-Ω to 8.9-kΩ
between ISET and VSS; Programs fast-charge current; use 1% tolerance. · p. 8
res 0-Ω to 15-kΩ
between ITERM and VSS; Programs termination current; leave open for default 10% termination. · p. 8
res 18-kΩ to 72-kΩ
between TMR and VSS; Programs safety timer duration. · p. 9
res 10-kΩ
between TS and VSS; Fixed resistor when the TS function is unused. · p. 9
res 1kΩ-100kΩ
between CHG and desired logic voltage rail; Charging-status pull-up; an LED is an alternative. · p. 8
res 1-kΩ to 100-kΩ
between PGOOD and desired logic voltage rail; Power-good pull-up; an LED is an alternative. · p. 8
res 1.1 kΩ to 8 kΩ
between ILIM and VSS; Programs the input current limit, adjustable up to 1.5 A. · p. 21

Specifications

80
ParameterConditionsAs printedPage
Input Voltage VIIN with respect to VSSmin -0.3 · max 28 V10
Input Voltage VIBAT with respect to VSSmin -0.3 · max 5 V10
Input Voltage VIOUT, EN1, EN2, CE, TS, ISET, PGOOD, CHG, ILIM, TMR, ITERM, SYSOFF, TD with respect to VSSmin -0.3 · max 7 V10
Input Current IIINmax 1.6 A10
Output Current (Continuous) IOOUTmax 5 A10
Output Current (Continuous) IOBAT (Discharge mode)max 5 A10
Output Current (Continuous) IOBAT (Charging mode); footnote (2)max 1.5 A10
Output Sink CurrentCHG, PGOODmax 15 mA10
Junction temperature TJmin -40 · max 150 °C10
Storage temperature Tstgmin -65 · max 150 °C10
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1); value ±2000max 2000 V10
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101(2); value ±500max 500 V10
IN voltage range VImin 4.35 · max 26 V10
IN operating voltage range VIBQ24074min 4.35 · max 10.2 V10
Input current, IN pin IINmax 1.5 A10
Current, OUT pin IOUTmax 4.5 A10
Current, BAT pin (Discharging) IBATmax 4.5 A10
Current, BAT pin (Charging) ICHGFootnote (2)max 1.5 A10
Junction Temperature TJmin -40 · max 125 °C10
Maximum input current programming resistor RILIMmin 1100 · max 8000 Ω10
Fast-charge current programming resistor (1) RISETUse a 1% tolerance resistormin 590 · max 8900 Ω10
Termination current programming resistor RITERMmin 0 · max 15 kΩ10
Timer programming resistor RTMRmin 18 · max 72 kΩ10
Junction-to-ambient thermal resistance RθJABQ2407x, RGT, 16 PINStyp 44.5 °C/W11
Junction-to-case (top) thermal resistance RθJC(top)BQ2407x, RGT, 16 PINStyp 54.2 °C/W11
Junction-to-board thermal resistance RθJBBQ2407x, RGT, 16 PINStyp 17.2 °C/W11
Junction-to-top characterization parameter ψJTBQ2407x, RGT, 16 PINStyp 1 °C/W11
Junction-to-board characterization parameter ψJBBQ2407x, RGT, 16 PINStyp 17.1 °C/W11
Junction-to-case (bottom) thermal resistance RθJC(bot)BQ2407x, RGT, 16 PINStyp 3.8 °C/W11
Undervoltage lock-out UVLOVIN: 0 V → 4 Vmin 3.2 · typ 3.3 · max 3.4 V12
Hysteresis on UVLO VhysVIN: 4 V → 0 Vmin 200 · max 300 mV12
Input power detection threshold VIN(DT)Input power detected when VIN > VBAT + VIN(DT); VBAT = 3.6 V, VIN: 3.5 V → 4 Vmin 55 · typ 80 · max 130 mV12
Hysteresis on VIN(DT) VhysVBAT = 3.6 V, VIN: 4 V → 3.5 Vmin 20 mV12
Deglitch time, input power detected status tDGL(PGOOD)Time measured from VIN: 0 V → 5 V 1 us rise-time to PGOOD = LOtyp 1.2 ms12
Input overvoltage protection threshold VOVPBQ24074; VIN: 5 V → 11 Vmin 10.2 · typ 10.5 · max 10.8 V12
Hysteresis on OVP VhysBQ24074; VIN: 11 V → 5 Vtyp 175 mV12
Input overvoltage blanking time (OVP fault deglitch) tDGL(OVP)typ 50 us12
Input overvoltage recovery time tRECTime measured from VIN: 11 V → 5 V with 1 us fall-time to PGOOD = LOtyp 1.2 ms12
Current source ISCILIM, ISET short-circuit detection, checked during startup; VIN > UVLO and VIN > VBAT + VIN(DT)typ 1.3 mA12
Sleep current into BAT pin IBAT(PDWN)CE = LO or HI, input power not detected, no load on OUT pin, TJ = 85°Ctyp 4.3 · max 6.5 uA12
Standby current into IN pin IINEN1= HI, EN2=HI, VIN = 6 V, TJ= 85°Ctyp 41.3 · max 50 uA12
Standby current into IN pin IINEN1= HI, EN2=HI, VIN = 10 V, TJ= 85°Ctyp 99.8 · max 200 uA12
Active supply current, IN pin ICCCE = LO, VIN = 6 V, no load on OUT pin, VBAT > VBAT(REG), (EN1, EN2) ≠ (HI, HI)typ 1.1 · max 1.5 mA12
VIN – VOUT VDO(IN-OUT)VIN = 4.3 V, IIN = 1 A, VBAT = 4.2 Vtyp 300 · max 475 mV12
VBAT – VOUT VDO(BAT-OUT)IOUT = 1 A, VIN = 0 V, VBAT > 3 Vtyp 50 · max 100 mV12
OUT pin voltage regulation (BQ24073, BQ24074) VO(REG)BQ24074; VIN > VOUT + VDO(IN-OUT)min 4.3 · typ 4.4 · max 4.5 V12
Maximum input current IINmaxEN1 = LO, EN2 = LOmin 90 · typ 95 · max 100 mA12
Maximum input current IINmaxEN1 = HI, EN2 = LOmin 450 · typ 475 · max 500 mA12
Maximum input current factor KILIMILIM = 500 mA to 1.5 Amin 1500 · typ 1610 · max 1720 AΩ12
Maximum input current factor KILIMILIM = 200 mA to 500 mAmin 1330 · typ 1525 · max 1720 AΩ12
Programmable input current limit range IINmaxEN2 = HI, EN1 = LO, RILIM = 8 kΩ to 1.1 kΩmin 200 · max 1500 mA12
Input voltage threshold when input current is reduced VIN-DPMEN2 = LO, EN1 = Xmin 4.35 · typ 4.5 · max 4.63 V12
Source current for BAT pin short-circuit detection IBATVBAT = 1.5 Vmin 4 · typ 7.5 · max 11 mA13
BAT pin short-circuit detection threshold VBAT(SC)VBAT risingmin 1.6 · typ 1.8 · max 2 V13
Battery charge voltage VBAT(REG)BQ24074min 4.16 · typ 4.2 · max 4.23 V13
Pre-charge to fast-charge transition threshold VLOWVVIN > VUVLO and VIN > VBAT + VIN(DT)min 2.9 · typ 3 · max 3.1 V13
Deglitch time on pre-charge to fast-charge transition tDGL1(LOWV)typ 25 ms13
Deglitch time on fast-charge to pre-charge transition tDGL2(LOWV)typ 25 ms13
Battery fast charge current range ICHGVBAT(REG) > VBAT > VLOWV, VIN = 5 V CE = LO, EN1 = LO, EN2 = HImin 100 · max 1500 mA13
Fast charge current factor KISETmin 797 · typ 890 · max 975 AΩ13
Pre-charge current factor KPRECHGmin 70 · typ 88 · max 106 AΩ13
Current for external termination-setting resistor IBIAS(ITERM)VIN > VUVLO and VIN > VBAT + VIN(DT)min 72 · typ 75 · max 78 uA13
K Factor for termination detection threshold (externally set) (BQ24074) KITERMBQ24074; USB500 or ISET mode (EN1, EN2) ≠ (LO, LO); CE = LO, VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPPM loop and thermal loop not activemin 0.0225 · typ 0.03 · max 0.0375 A13
K Factor for termination detection threshold (externally set) (BQ24074) KITERMBQ24074; USB100 mode (EN1, EN2) = (LO, LO); CE = LO, VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPPM loop and thermal loop not activemin 0.008 · typ 0.01 · max 0.012 A13
Deglitch time, termination detected tDGL(TERM)typ 25 ms13
Deglitch time, recharge threshold detected tDGL(RCH)typ 62.5 ms13
Delay time, input power loss to OUT LDO turn-off tDGL(NO-IN)VBAT = 3.6 V. Time measured from VIN: 5 V → 3 V 1 us fall-timetyp 20 ms13
Sink current for battery detection IBAT(DET)VBAT = 2.5 Vmin 5 · typ 7.5 · max 10 mA13
Battery detection timer tDETBAT high or lowtyp 250 ms13
Pre-charge safety timer value tPRECHGTMR = floatingmin 1440 · typ 1800 · max 2160 s13
Charge safety timer value tMAXCHGTMR = floatingmin 14400 · typ 18000 · max 21600 s13
Timer factor KTMRmin 36 · typ 48 · max 60 s/kΩ13
NTC bias current INTCVIN > UVLO and VIN > VBAT + VIN(DT)min 72 · typ 75 · max 78 uA13
High temperature trip point VHOTBattery charging, VTS Fallingmin 270 · typ 300 · max 330 mV13
Hysteresis on high trip point VHYS(HOT)Battery charging, VTS Rising from VHOTtyp 30 mV13
Logic LOW input voltage VILEN1, EN2, CE, SYSOFF, TDmin 0 · max 0.4 V14
Logic HIGH input voltage VIHEN1, EN2, CE, SYSOFF, TDmin 1.4 · max 6 V14
Input sink current IILEN1, EN2, CE, SYSOFF, TD; VIL= 0 Vmax 1 uA14
Input source current IIHEN1, EN2, CE, SYSOFF, TD; VIH= 1.4 Vmax 10 uA14
Output LOW voltage VOLPGOOD, CHG; ISINK = 5 mAmax 0.4 V14

Pins, by the datasheet

16
1 TS
External battery-pack 10kΩ NTC thermistor input; connect a 10-kΩ resistor to VSS when unused. · p. 9
2 BAT
Charger power stage output and battery voltage sense input; connect to battery positive and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
3 BAT
Charger power stage output and battery voltage sense input; connect to battery positive and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
4 CE
Active-low charge enable; drive high to disable charging or low to enable it; do not leave unconnected. · p. 8
5 EN2
Input current limit configuration input with EN1; do not leave unconnected. · p. 8
6 EN1
Input current limit configuration input with EN2; do not leave unconnected. · p. 8
7 PGOOD
Pulls to VSS when a valid input source is detected; connect a 1-kΩ to 100-kΩ pull-up to the desired logic rail or use an LED. · p. 8
8 VSS
Connect to the thermal pad and circuit ground rail. · p. 9
9 CHG
Pulls to VSS while charging and becomes high impedance when charging completes or is disabled; use a pull-up or LED. · p. 8
10 OUT
System supply output; connect to system load and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
11 OUT
System supply output; connect to system load and bypass to VSS with a 4.7-uF to 47-uF ceramic capacitor. · p. 8
12 ILIM
Connect a 1100-Ω to 8-kΩ resistor to VSS to program maximum input current with EN2=1 and EN1=0; leaving unconnected disables charging. · p. 8
13 IN
External DC supply input from adapter or USB; bypass to VSS with 1 uF to 10 uF. · p. 8
14 TMR
Programs pre-charge and fast-charge safety timers; ground to disable timers, use 18-kΩ to 72-kΩ to VSS to program, or leave open for defaults. · p. 9
15 ITERM
Connect a 0-Ω to 15-kΩ resistor to VSS to program termination current; leave open for the default 10% threshold. · p. 8
16 ISET
Connect a 590-Ω to 8.9-kΩ resistor to VSS to program fast-charge current; its voltage monitors charging current; leaving open disables charging. · p. 8

Open-source boards using it

6
  • 2 layers26 × 40 mmNervous EDA, the printed circuit board in 3D

    Nervous EDA

    sensors-inl/Nervous-EDA

    ECAD design files, firmware source code and standalone application for the EDA sensor of the Nervous project.

    55 parts3MIT
  • 2 layers26 × 40 mmNervous ECG, the printed circuit board in 3D

    Nervous ECG

    sensors-inl/Nervous-ECG

    ECAD design files, firmware source code and standalone application for the ECG sensor of the Nervous project.

    65 parts2MIT
  • 4 layers122 × 76 mmESP iRadio, the printed circuit board in 3D

    ESP iRadio

    hghaken/ESP-iRadio

    ESP32 internet radio with Bluetooth A2DP output (headphones/speaker), 1.69" display and web control

    122 partsGPL-3.0
  • 2 layers65 × 65.5 mmSchmatic, the printed circuit board in 3D

    Schmatic

    Yorha-7/Rocket

    in this repo we are simulating rocket basic physics and make a onboard flight computer which utilizes MCU, gyro, pressure sensor, fin servo controls, to get realtime target tracking abilities to a solid fuel rocket.

    77 parts
  • 2 layers36.5 × 25.1 mmSolarCharger, the printed circuit board in 3D

    SolarCharger

    dean-meyer/PCB-Designs

    PCB design projects from physics courses and research.

    14 parts
  • 2 layers31.2 × 20.3 mmSolarCharger v2, the printed circuit board in 3D

    SolarCharger v2

    dean-meyer/PCB-Designs

    PCB design projects from physics courses and research.

    14 parts

Parts like it

7

Questions

Is there a KiCad symbol and footprint for the BQ24074RGTT?

Yes. The symbol is Battery_Management:BQ24074RGT and the footprint Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ24074RGTT?

VQFN-16-EP(3x3), with 17 pins. Its footprint is drawn on this page.

Where is the BQ24074RGTT datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ24074RGTT?

JLCPCB lists it as part C2861252, with 168 in stock; the sellers' links on this page open their listings.

What can replace the BQ24074RGTT?

Parts like it in the library: the BQ24075RGT by Texas Instruments, the BQ24072RGTR by Texas Instruments, the BQ24073RGTR by Texas Instruments and the BQ24074RGTR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ24074RGTT?

6 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.