
EnvPico nRF52840
Envious-Data/EnvPico-nRF52840
a nRF52840 MCU board in the form of a raspberry pi pico.

a nRF52840 MCU board in the form of a raspberry pi pico.
EnvPico nRF52840 is an open-source printed circuit board by Envious-Data, from the Envious-Data/EnvPico-nRF52840 repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 21.2 × 57.2 mm with 45 parts on 125 nets, routed with 283 tracks and 31 vias.
It is built around the BQ24072RGTR, 1N4002W and TYPE-C-31-M-12. Its parts include 22 capacitors, 6 resistors, 5 inductors, 3 ICs and 3 connectors. It belongs with the nRF52 and nRF5x boards of this library.
A nRF52840 MCU board that is in the size of a raspberry pi pico.

like the other boards Ive designed, I wanted to make sure this would fit in place of a raspberry pi pico incase you wanted wifi + bluetooth and battery on one board instead of a stack of packs for the pi pico.
this is intended to be used with my keyboards again like the other boards but ive made sure to include a decently powerful PMIC just so its capable of other things too, the BQ24072RGT should be capable of upto 1.5A output but around 500mA charging.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C3, C7, C18, C22 |
| 3 | 100nF | Capacitor_SMD:C_0402_1005Metric | C2, C5, C6 |
| 3 | 10K 0402 | Resistor_SMD:R_0402_1005Metric | R11, R12, R14 |
| 2 | 10uH | Inductor_SMD:L_0603_1608Metric | L3, L4 |
| 2 | 15pF 0402 | Capacitor_SMD:C_0402_1005Metric | C10, C11 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C4, C23 |
| 2 | 2.54mm header 01x20 | 2.54mmheadercastelation:PinHeader_1x20_P2.54mm_Vertical_castelated | J3, J4 |
| 2 | 4.7uf 0402 | Capacitor_SMD:C_0402_1005Metric | C9, C21 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 1 | 0.1uf 0402 | Capacitor_SMD:C_0402_1005Metric | C12 |
| 1 | 0402 0.8pF | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | 0402 10uF | Resistor_SMD:R_0402_1005Metric | C20 |
| 1 | 0402 1uF | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 0402 led | LED_SMD:LED_0402_1005Metric | D2 |
| 1 | 100nF 0402 | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 100ohm | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 100pF 0402 | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 10uf 0402 | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 15nH | Capacitor_SMD:C_0402_1005Metric | L2 |
| 1 | 1N4002W | Diode_SMD:D_SOD-123 | D4 |
| 1 | 32MHz 12pF 2016-4P | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | 47nF | Capacitor_SMD:C_0402_1005Metric | C24 |
| 1 | 5.6nH 0402 | Inductor_SMD:L_0402_1005Metric | L5 |
| 1 | 820pF 0402 - DNP | Capacitor_SMD:C_0402_1005Metric | C17 |
| 1 | Antenna | RF_Antenna:Johanson_2450AT43F0100 | AE1 |
| 1 | BM03B 3P | Connector_JST:JST_SUR_BM03B-SURS-TF_1x03-1MP_P0.80mm_Vertical | J5 |
| 1 | BQ24072RGT | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm | U2 |
| 1 | INDUCTOR 2.2uH 0603 | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | LM3671MF 3.3 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | Li-Po Battery | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BT1 |
| 1 | TYPE-C-31-M-12 | HRO-TYPE-C31-M-12:HRO-TYPE-C-31-M-12 | USB1 |
| 1 | nRF52840 | Package_DFN_QFN:Nordic_AQFN-73-1EP_7x7mm_P0.5mm | U3 |

Envious-Data/EnvPico-nRF52840
a nRF52840 MCU board in the form of a raspberry pi pico.


RetroScaler/RP2040-PICO-BOOT
Raspberry PI RP2040 PICOBOOT for the Game cube console




Auroxin/N64xCart-Dumper
an open hardware / firmware project for dumping Nintendo 64 cartridges as a USB mass storage device

TrojanPinata/Model-B
A 75% keyboard based on the RP2040 - with hotswappable switches, OLED display and rotary encoder

nico25112005/Nerf-ATG-Electronics
This repository contains the electronic design files for a custom printed circuit board (PCB) developed to enhance Nerf LaserOps blasters.
It measures 21.2 × 57.2 mm and has 2 copper layers, 1.6 mm thick.
45 parts, built around the BQ24072RGTR, 1N4002W and TYPE-C-31-M-12. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Envious-Data/EnvPico-nRF52840 repository on GitHub, at the commit this page was made from: the board is PCB-Variant-A/EnvPico-nRF52840.kicad_pcb and its schematic PCB-Variant-A/EnvPico-nRF52840.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).