Skip to the content

ADS1115IDGST

Texas InstrumentsExtended

-40℃~+125℃ 16 1LSB 1MHz 2V~5.5V 2uA 2、4 860Hz Built-in Built-in I2C Multiplexers、Power-on reset Sigma-Delta Support Yes VSSOP-10-0.5mm Analog to Digital Converters (ADC) ROHS

Part id
ti/ADS1115IDGST
Category
Analog To Digital Converters (ADC)
Package
VSSOP-10-0.5mm
Pins
10
In stock
1,845 at JLCPCB (C468683)
Used on
19 open-source boards

Overview

The ADS1115IDGST is an analog To Digital Converter made by Texas Instruments in a VSSOP-10-0.5mm package with 10 pins. -40℃~+125℃ 16 1LSB 1MHz 2V~5.5V 2uA 2、4 860Hz Built-in Built-in I2C Multiplexers、Power-on reset Sigma-Delta Support Yes VSSOP-10-0.5mm Analog to Digital Converters (ADC) ROHS.

PCBKit's library has its KiCad symbol (Analog_ADC:ADS1115IDGS, from KiCad's library) and its footprint (Package_SO:TSSOP-10_3x3mm_P0.5mm, from KiCad's library), ready for a KiCad board. 1,845 are in stock at JLCPCB (part C468683). 19 open-source boards in 17 repositories on GitHub use it.

Symbol

1ADDR2ALERT/RDY3GND4AIN05AIN16AIN27AIN38VDD9SDA10SCL
Analog_ADC:ADS1115IDGSFrom KiCad's library

Footprint

Package_SO:TSSOP-10_3x3mm_P0.5mmFrom KiCad's library

From the datasheet

14
Supply, least
2 V · VDD, recommended operating min · p. 4
Supply, most
5.5 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
7 V · VDD to GND, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
125 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Junction temperature absolute max · p. 4
Takes working
150 µA · VDD operating current typical, 3.3V, TA = 25°C · p. 6
Takes at most
300 µA · VDD operating current max over temperature, 3.3V · p. 6
Takes asleep
500 nA · VDD power-down current typical, 3.3V, TA = 25°C · p. 6
A pin gives at most
10 mA · Continuous input current absolute max, any pin except power supply pins · p. 4
Junction to air (DGS (VSSOP))
182.7 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to board (DGS (VSSOP))
103.8 K/W · Junction-to-board thermal resistance · p. 4
Junction to case (DGS (VSSOP))
67.2 K/W · Junction-to-case top thermal resistance · p. 4
Data rate, most
3.4 Mbit/s · I2C high-speed mode SCL clock frequency max · p. 6

What it is and has

9
ADC
16-bit, maximum 860 SPS, two differential or four single-ended inputs, PGA, I2C, comparator · p. 3
I2C addressing
Four pin-selectable addresses · p. 1
Settling
Single-cycle · p. 1
Voltage reference
Internal low-drift · p. 1
Oscillator
Integrated, 1MHz · p. 15
Programmable data rates
8SPS, 16SPS, 32SPS, 64SPS, 128SPS, 250SPS, 475SPS, 860SPS · p. 15
Resolution
16-bit · p. 1
Interface
I2C-compatible · p. 1
Integrated functions
Internal reference, oscillator, programmable comparator · p. 1

Around it

8
cap 0.1μF
between VDD and GND; Power-supply decoupling capacitor. · p. 3
res unspecified
between SCL and VDD; Pullup resistor. · p. 3
res unspecified
between SDA and VDD; Pullup resistor. · p. 3
res unspecified
between ALERT/RDY and VDD; Pullup resistor for the open-drain output. · p. 3
cap 0.1µF minimum
between VDD and GND; MLCC with low ESR and ESL; place as close to the power-supply pin as possible using low-impedance connections. · p. 37
res 100Ω
between OPA333 VOUT and AINP; R5 in the example low-side current-shunt circuit; 1% precision resistor. · p. 35
cap 0.22µF
between AINP and AINN; CDIFF in the example differential input filter. · p. 35
cap 0.022µF
between AINP and GND; CCM1 in the example common-mode input filter. · p. 35

Specifications

75
ParameterConditionsAs printedPage
Power-supply voltageVDD to GNDmin -0.3 · max 7 V4
Digital input voltageSDA, SCL, ADDR, ALERT/RDY; minimum GND – 0.3max 5.5 V4
Input current, continuousAny pin except power supply pinsmin -10 · max 10 mA4
Temperature TAOperating ambientmin -40 · max 125 °C4
Temperature TJJunctionmin -40 · max 150 °C4
Temperature TstgStoragemin -60 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; value ±500 Vmax 500 V4
Power supply (VDD to GND)min 2 · max 5.5 V4
Digital input voltage VDIGMinimum GNDmax 5.5 V4
Operating ambient temperature TAmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADGS (VSSOP), 10 PINStyp 182.7 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DGS (VSSOP), 10 PINStyp 67.2 °C/W4
Junction-to-board thermal resistance RθJBDGS (VSSOP), 10 PINStyp 103.8 °C/W4
Junction-to-top characterization parameter ψJTDGS (VSSOP), 10 PINStyp 10.2 °C/W4
Junction-to-board characterization parameter ψJBDGS (VSSOP), 10 PINStyp 102.1 °C/W4
Common-mode input impedanceFSR = ±6.144Vtyp 10 MΩ5
Common-mode input impedanceFSR = ±4.096V, FSR = ±2.048Vtyp 6 MΩ5
Common-mode input impedanceFSR = ±1.024Vtyp 3 MΩ5
Common-mode input impedanceFSR = ±0.512V, FSR = ±0.256Vtyp 100 MΩ5
Differential input impedanceFSR = ±6.144Vtyp 22 MΩ5
Differential input impedanceFSR = ±4.096Vtyp 15 MΩ5
Differential input impedanceFSR = ±2.048Vtyp 4.9 MΩ5
Differential input impedanceFSR = ±1.024Vtyp 2.4 MΩ5
Differential input impedanceFSR = ±0.512V, ±0.256Vtyp 710 kΩ5
Resolution (no missing codes)min 16 Bits5
Data rate variationAll data ratesmin -10 · max 10 %5
Integral nonlinearity INLDR = 8SPS, FSR = ±2.048V; best-fit INL, covers 99% of full-scalemax 1 LSB5
Offset errorFSR = ±2.048V, differential inputs; typical ±1 LSBmin -3 · max 3 LSB5
Offset drift over temperatureFSR = ±2.048Vtyp 0.005 LSB/°C5
Offset power-supply rejectionFSR = ±2.048V, DC supply variationtyp 1 LSB/V5
Offset channel matchMatch between any two inputstyp 3 LSB5
Gain errorFSR = ±2.048V, TA = 25°Ctyp 0.01 · max 0.15 %5
Gain drift over temperatureFSR = ±0.256Vtyp 7 ppm/°C5
Gain drift over temperatureFSR = ±2.048Vtyp 5 · max 40 ppm/°C5
Gain drift over temperatureFSR = ±6.144Vtyp 5 ppm/°C5
Gain power-supply rejectiontyp 80 ppm/V5
Gain matchMatch between any two gainstyp 0.02 · max 0.1 %5
Gain channel matchMatch between any two inputstyp 0.05 · max 0.1 %5
Common-mode rejection ratio CMRRAt DC, FSR = ±0.256Vtyp 105 dB5
Common-mode rejection ratio CMRRAt DC, FSR = ±2.048Vtyp 100 dB5
Common-mode rejection ratio CMRRAt DC, FSR = ±6.144Vtyp 90 dB5
Common-mode rejection ratio CMRRfCM = 60Hz, DR = 8SPStyp 105 dB5
Common-mode rejection ratio CMRRfCM = 50Hz, DR = 8SPStyp 105 dB5
High-level input voltage VIHMinimum 0.7 VDDmax 5.5 V5
Low-level output voltage VOLIOL = 3mA; minimum GNDtyp 0.15 · max 0.4 V5
Input leakage currentGND < VDIG < VDDmin -10 · max 10 uA5
Supply current IVDDPower-down, TA = 25°C; VDD = 3.3Vtyp 0.5 · max 2 uA6
Supply current IVDDOperating, TA = 25°C; VDD = 3.3Vtyp 150 · max 200 uA6
Supply current IVDDOperating, TA = –40°C to +125°C; VDD = 3.3Vmax 300 uA6
Power dissipation PDVDD = 5.0Vtyp 0.9 mW6
Power dissipation PDVDD = 3.3 Vtyp 0.5 mW6
Power dissipation PDVDD = 2.0Vtyp 0.3 mW6
SCL clock frequency fSCLFAST MODEmin 0.01 · max 0.4 MHz6
SCL clock frequency fSCLHIGH-SPEED MODEmin 0.01 · max 3.4 MHz6
Bus free time between START and STOP condition tBUFFAST MODEmin 600 ns6
Bus free time between START and STOP condition tBUFHIGH-SPEED MODEmin 160 ns6
Hold time after repeated START condition. After this period, the first clock is generated. tHDSTAFAST MODEmin 600 ns6
Hold time after repeated START condition. After this period, the first clock is generated. tHDSTAHIGH-SPEED MODEmin 160 ns6
Setup time for a repeated START condition tSUSTAFAST MODEmin 600 ns6
Setup time for a repeated START condition tSUSTAHIGH-SPEED MODEmin 160 ns6
Setup time for STOP condition tSUSTOFAST MODEmin 600 ns6
Setup time for STOP condition tSUSTOHIGH-SPEED MODEmin 160 ns6
Data hold time tHDDATFAST MODEmin 0 ns6
Data hold time tHDDATHIGH-SPEED MODEmin 0 ns6
Data setup time tSUDATFAST MODEmin 100 ns6
Data setup time tSUDATHIGH-SPEED MODEmin 10 ns6
Low period of the SCL clock pin tLOWFAST MODEmin 1300 ns6
Low period of the SCL clock pin tLOWHIGH-SPEED MODEmin 160 ns6
High period for the SCL clock pin tHIGHFAST MODEmin 600 ns6
High period for the SCL clock pin tHIGHHIGH-SPEED MODEmin 60 ns6
Fall time for both SDA and SCL signals tFFAST MODEmax 300 ns6
Fall time for both SDA and SCL signals tFHIGH-SPEED MODE; bus line capacitive load must not exceed 400pFmax 160 ns6
Rise time for both SDA and SCL signals tRFAST MODEmax 300 ns6
Rise time for both SDA and SCL signals tRHIGH-SPEED MODE; bus line capacitive load must not exceed 400pFmax 160 ns6

Pins, by the datasheet

10
1 ADDR
I2C target address select. · p. 3
2 ALERT/RDY
Comparator output or conversion ready; connect to VDD using a pullup resistor. · p. 3
3 GND
Ground. · p. 3
4 AIN0
Analog input 0. · p. 3
5 AIN1
Analog input 1. · p. 3
6 AIN2
Analog input 2. · p. 3
7 AIN3
Analog input 3. · p. 3
8 VDD
Power supply; connect a 0.1uF power-supply decoupling capacitor to GND. · p. 3
9 SDA
Serial data input and output; connect to VDD using a pullup resistor. · p. 3
10 SCL
Serial clock input; connect to VDD using a pullup resistor. · p. 3

Ordering codes, by the datasheet

14
ADS1115IDGSR.B
VSSOP (DGS) | 10 · 2500, LARGE T&R; operating temperature -40 to 125°C · p. 43
ADS1115IDGST
VSSOP (DGS) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IDGST.A
VSSOP (DGS) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IDGST.B
VSSOP (DGS) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IDYNR
SOT-5X3 (DYN) | 10 · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGR
X2QFN (RUG) | 10 · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGR.A
X2QFN (RUG) | 10 · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGR.B
X2QFN (RUG) | 10 · 3000, LARGE T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGT
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGT.A
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGT.B
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGTG4
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGTG4.A
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43
ADS1115IRUGTG4.B
X2QFN (RUG) | 10 · 250, SMALL T&R; operating temperature -40 to 125°C · p. 43

Open-source boards using it

19See all 19
  • 2 layers191.3 × 181.7 mmIO Card G3, the printed circuit board in 3D

    IO Card G3

    PerMalmberg/IO-Card-G3

    This is my custom I/O card, third generation. Main purpose is to serve as an alarm system.

    400 parts7MIT
  • 4 layers75 × 170 mmOpencalc pcb V5, the printed circuit board in 3D

    Opencalc pcb V5

    CoryPearl/opencalc

    A new and improved, better than the TI-84, open-source, graphing calculator

    194 parts2
  • 2 layersAdc ads1115, the printed circuit board in 3D

    Adc ads1115

    Nuclear-Squid/KiCad-Templates

    A KiCad plugin to save and reuse schematic + routing templates.

    8 parts1GPL-3.0
  • 2 layers52 × 88 mmPRAN RAKSHAK RevA, the printed circuit board in 3D

    PRAN RAKSHAK RevA

    SrivarsanK/PranRakshak

    Project README · Hardware designs · Original PCB ZIP

    49 parts1
  • 4 layers416 × 130 mmHardware pruefadapter, the printed circuit board in 3D

    Hardware pruefadapter

    CodeByMika/technikerarbeit2026-hardwarepruefadapter

    Im Schuljahr 2025/2026 wurde im Rahmen der Ausbildung zum staatlich geprüften Techniker diese Technikerarbeit in Zusammenarbeit mit der Gottlieb Daimler Schule 2 in Sindelfingen sowie der SOTEC GmbH & Co KG in…

    454 parts
  • 2 layers100 × 100 mmHour meter board microfit can handroute, the printed circuit board in 3D

    Hour meter board microfit can handroute

    ilomon10/embedded-totalizer-hour-meter

    ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator

    152 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ADS1115IDGST?

Yes. The symbol is Analog_ADC:ADS1115IDGS and the footprint Package_SO:TSSOP-10_3x3mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ADS1115IDGST?

VSSOP-10-0.5mm, with 10 pins. Its footprint is drawn on this page.

Where is the ADS1115IDGST datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the ADS1115IDGST?

JLCPCB lists it as part C468683, with 1,845 in stock; the sellers' links on this page open their listings.

What can replace the ADS1115IDGST?

Parts like it in the library: the ADS1015IDGS by Texas Instruments, the ADS1014IDGS by Texas Instruments, the ADS1114IDGSR by Texas Instruments and the ADS1118IDGS by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ADS1115IDGST?

19 boards in 17 repositories on GitHub; the most starred are listed on this page, with their KiCad files.