Skip to the content
1234567891011121314

ATTINY1614-SSN

Microchip TechnologyExtended

-40℃~+105℃ 1.8V~5.5V 10bit 12 16KB 20MHz 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH SOIC-14 Microcontrollers (MCU/MPU/SOC) ROHS

Part id
microchip/ATTINY1614-SSN
Category
Microcontrollers (MCU, MPU, SOC)
Package
SOIC-14
Pins
14
In stock
185 at JLCPCB (C481364)
Used on
60 open-source boards

Overview

The ATTINY1614-SSN is a microcontroller made by Microchip Technology in a SOIC-14 package with 14 pins. -40℃~+105℃ 1.8V~5.5V 10bit 12 16KB 20MHz 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH SOIC-14 Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_Microchip_ATtiny:ATtiny1614-SS, from KiCad's library) and its footprint (Package_SO:SOIC-14_3.9x8.7mm_P1.27mm, from KiCad's library), ready for a KiCad board. 185 are in stock at JLCPCB (part C481364). 60 open-source boards in 46 repositories on GitHub use it.

Symbol

1VCC2PA43PA54PA65PA76PB37PB28PB19PB010RESET/PA011PA112PA213PA314GND
MCU_Microchip_ATtiny:ATtiny1614-SSFrom KiCad's library

Footprint

1234567891011121314
Package_SO:SOIC-14_3.9x8.7mm_P1.27mmFrom KiCad's library

From the datasheet

11
Supply, least
1.8 V · VDD, recommended operating min · p. 506
Supply, most
5.5 V · VDD, recommended operating max · p. 506
Supply, absolute maximum
6 V · VDD, absolute maximum · p. 505
Takes working
10.2 mA · VDD, active typical at 20 MHz, 5V, peripherals disabled · p. 508
Takes asleep
100 nA · VDD, power-down/standby typical at 3V, 25°C, all peripherals stopped · p. 508
A pin gives at most
40 mA · I/O pin sink/source absolute maximum · p. 505
Edge
1.3 ns · Fall time typical at VDD = 5.0V, load = 20 pF · p. 513
Junction to air (SOIC)
58 K/W · Junction-to-ambient thermal resistance · p. 583
Junction to case (SOIC)
26 K/W · Junction-to-case thermal resistance · p. 583
Takes at most
10.2 mA · VDD, largest stated typical active current at 20 MHz, 5 V · p. 508
Edge
2.7 ns · typical SPI master SCK rise time · p. 516

What it is and has

26
CPU
AVR · p. 1
Maximum clock
20 MHz · p. 1
Flash memory
16 KB, in-system self-programmable · p. 1
EEPROM
256 bytes · p. 1
SRAM
2 KB · p. 1
Interrupt controller
Two-level · p. 1
Hardware multiplier
Two-cycle · p. 1
Flash endurance
10,000 write/erase cycles · p. 1
EEPROM endurance
100,000 write/erase cycles · p. 1
Data retention
40 years at 55°C · p. 1
Reset
Power-on Reset (POR) · p. 1
Brown-out detection
Brown-out Detector (BOD) · p. 1
Internal oscillator
16/20 MHz low-power RC · p. 1
Internal low-power oscillator
32.768 kHz ULP RC · p. 1
External crystal oscillator
32.768 kHz · p. 1
Programming and debugging
Single-pin UPDI · p. 1
Sleep modes
Idle, Standby, Power-Down · p. 90
CPU
AVR® CPU · p. 1
I/O access
Single-cycle · p. 1
Flash write/erase endurance
10,000 cycles · p. 1
EEPROM write/erase endurance
100,000 cycles · p. 1
Power-on Reset
POR · p. 1
Brown-out Detector
BOD · p. 1
Internal RC oscillator
16/20 MHz, low-power · p. 1
Internal ULP RC oscillator
32.768 kHz · p. 1
Internal ULP oscillator
32.768 kHz · p. 1

Specifications

246
ParameterConditionsAs printedPage
Power supply voltage VDDmin -0.5 · max 6 V505
Current into a VDD pin IVDDT = [-40, 85]°Cmax 200 mA505
Current into a VDD pin IVDDT = [85, 125]°Cmax 100 mA505
Current out of a GND pin IGNDT = [-40, 85]°Cmax 200 mA505
Current out of a GND pin IGNDT = [85, 125]°Cmax 100 mA505
RESET pin voltage with respect to GND VRSTmin -0.5 · max 13 V505
Pin voltage with respect to GND VPINmin -0.5 V505
I/O pin sink/source current IPINmin -40 · max 40 mA505
I/O pin injection current except RESET pin Ic1VPIN < GND – 0.6V or 5.5V < VPIN ≤ 6.1V; 4.9V < VDD ≤ 5.5Vmin -1 · max 1 mA505
I/O pin injection current except RESET pin Ic2VPIN < GND – 0.6V or VPIN ≤ 5.5V; VDD ≤ 4.9Vmin -15 · max 15 mA505
Sum of I/O pin injection current except RESET pin Ictotmin -45 · max 45 mA505
Storage temperature Tstoragemin -65 · max 150 °C505
Operating supply voltage VDDOperation ensured down to 1.8V or BOD triggering level, VBOD; extended temperature range only ensured down to 2.7Vmin 1.8 · max 5.5 V506
Operating temperature range TStandard temperature range; refer to device ordering codesmin -40 · max 105 °C506
Operating temperature range TExtended temperature range; refer to device ordering codes; only ensured down to 2.7Vmin -40 · max 125 °C506
Operating system clock frequency CLK_CPUVDD = [1.8, 5.5]V; T = [-40, 105]°Cmin 0 · max 5 MHz506
Operating system clock frequency CLK_CPUVDD = [2.7, 5.5]V; T = [-40, 105]°Cmin 0 · max 10 MHz506
Operating system clock frequency CLK_CPUVDD = [4.5, 5.5]V; T = [-40, 105]°Cmin 0 · max 20 MHz506
Operating system clock frequency CLK_CPUVDD = [2.7, 5.5]V; T = [-40, 125]°Cmin 0 · max 8 MHz506
Operating system clock frequency CLK_CPUVDD = [4.5, 5.5]V; T = [-40, 125]°Cmin 0 · max 16 MHz506
Active power consumptionCLK_CPU = 20 MHz (OSC20M), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 10.2 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 5.5 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 3.1 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 3.2 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 1.8 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 2V, T = 25°C, peripherals disabled, without I/O drivetyp 1.2 mA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 5V, T = 25°C, peripherals disabled, without I/O drivetyp 13.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 3V, T = 25°C, peripherals disabled, without I/O drivetyp 7.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 2V, T = 25°C, peripherals disabled, without I/O drivetyp 5 uA508
Idle power consumptionCLK_CPU = 20 MHz (OSC20M), VDD = 5V, T = 25°C; maximum based on characterizationtyp 4.3 · max 6.3 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 5V, T = 25°C; maximum based on characterizationtyp 2.2 · max 3.1 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2), VDD = 3V, T = 25°C; maximum based on characterizationtyp 1.1 · max 1.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 5V, T = 25°C; maximum based on characterizationtyp 1.1 · max 1.6 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 3V, T = 25°Ctyp 0.6 · max 0.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4), VDD = 2V, T = 25°Ctyp 0.4 mA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 5V, T = 25°C; maximum based on characterizationtyp 8.2 · max 20 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 3V, T = 25°C; maximum based on characterizationtyp 4.2 · max 15 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K), VDD = 2V, T = 25°Ctyp 2.6 uA508
Standby power consumptionRTC running at 1.024 kHz from external XOSC32K (CL=7.5 pF), VDD = 3V, T = 25°Ctyp 0.69 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 25°Ctyp 0.71 · max 3 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 85°C; maximum based on characterizationmax 6 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K, VDD = 3V, T = 125°Cmax 8 uA508
Power-down/Standby power consumptionAll peripherals stopped, VDD = 3V, T = 25°Ctyp 0.1 · max 2 uA508
Power-down/Standby power consumptionAll peripherals stopped, VDD = 3V, T = 85°C; maximum based on characterizationmax 5 uA508
Power-down/Standby power consumptionAll peripherals stopped, VDD = 3V, T = 125°Cmax 7 uA508
Reset power consumptionReset line pulled down, VDD = 3V, T = 25°Ctyp 100 uA509
Start-up time from any Reset release twakeupVDD = 3V, T = 25°C, OSC20Mtyp 200 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 20 MHz, VDD = 5V, T = 25°Ctyp 1 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 10 MHz, VDD = 3V, T = 25°Ctyp 2 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 5 MHz, VDD = 2V, T = 25°Ctyp 4 us509
Wake-up from Standby and Power-Down sleep mode twakeupVDD = 3V, T = 25°C, OSC20Mtyp 10 us509
BODContinuous; VDD = 3V, T = 25°C, OSC20M at 1 MHz, Idle sleep modetyp 19 uA509
BODSampling @ 1 kHz; VDD = 3V, T = 25°C, OSC20M at 1 MHz, Idle sleep modetyp 1 uA509
TCA16-bit count @ 1 MHz; VDD = 3V, T = 25°C, OSC20M at 1 MHz, Idle sleep modetyp 13 uA509
TCB16-bit count @ 1 MHz; VDD = 3V, T = 25°C, OSC20M at 1 MHz, Idle sleep modetyp 7.5 uA509
RTC16-bit count @ 32.768 kHz @ OSCULP32K; VDD = 3V, T = 25°C, Idle sleep modetyp 1 uA509
Frequency fCLCLVDD = [1.8, 5.5]Vmin 0 · max 5 MHz513
Frequency fCLCLVDD = [2.7, 5.5]Vmin 0 · max 10 MHz513
Frequency fCLCLVDD = [4.5, 5.5]Vmin 0 · max 20 MHz513
Clock period tCLCLVDD = [1.8, 5.5]Vmin 200 ns513
Clock period tCLCLVDD = [2.7, 5.5]Vmin 100 ns513
Clock period tCLCLVDD = [4.5, 5.5]Vmin 50 ns513
High time tCHCXVDD = [1.8, 5.5]Vmin 80 ns513
High time tCHCXVDD = [2.7, 5.5]Vmin 40 ns513
High time tCHCXVDD = [4.5, 5.5]Vmin 20 ns513
Low time tCLCXVDD = [1.8, 5.5]Vmin 80 ns513
Low time tCLCXVDD = [2.7, 5.5]Vmin 40 ns513
Low time tCLCXVDD = [4.5, 5.5]Vmin 20 ns513
Input low-voltage, except RESET pin as I/O VILTA = [-40, 105]°C, VDD = [1.8, 5.5]Vmin -0.2 V513
I/O pin drive strength VOLVDD = 1.8V, IOL = 1.5 mA; TA = [-40, 105]°Cmax 0.36 V513
I/O pin drive strength VOLVDD = 3.0V, IOL = 7.5 mA; TA = [-40, 105]°Cmax 0.6 V513
I/O pin drive strength VOLVDD = 5.0V, IOL = 15 mA; TA = [-40, 105]°Cmax 1 V513
I/O pin drive strength VOHVDD = 1.8V, IOH = 1.5 mA; TA = [-40, 105]°Cmin 1.44 V513
I/O pin drive strength VOHVDD = 3.0V, IOH = 7.5 mA; TA = [-40, 105]°Cmin 2.4 V513
I/O pin drive strength VOHVDD = 5.0V, IOH = 15 mA; TA = [-40, 105]°Cmin 4 V513
Maximum combined I/O sink current per pin group ItotalTA = [-40, 105]°C, VDD = [1.8, 5.5]Vmax 100 mA513
Maximum combined I/O source current per pin group ItotalTA = [-40, 105]°C, VDD = [1.8, 5.5]Vmax 100 mA513
Input low-voltage on RESET pin as I/O VIL2TA = [-40, 105]°C, VDD = [1.8, 5.5]Vmin -0.2 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 1.8V, IOL = 0.1 mA; TA = [-40, 105]°Cmax 0.36 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 3.0V, IOL = 0.25 mA; TA = [-40, 105]°Cmax 0.6 V513
I/O pin drive strength on RESET pin as I/O VOL2VDD = 5.0V, IOL = 0.5 mA; TA = [-40, 105]°Cmax 1 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 1.8V, IOH = 0.1 mA; TA = [-40, 105]°Cmin 1.44 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 3.0V, IOH = 0.25 mA; TA = [-40, 105]°Cmin 2.4 V513
I/O pin drive strength on RESET pin as I/O VOH2VDD = 5.0V, IOH = 0.5 mA; TA = [-40, 105]°Cmin 4 V513
Rise time tRISEVDD = 3.0V, load = 20 pF; TA = [-40, 105]°Ctyp 2.5 ns513
Rise time tRISEVDD = 5.0V, load = 20 pF; TA = [-40, 105]°Ctyp 1.5 ns513
Fall time tFALLVDD = 3.0V, load = 20 pF; TA = [-40, 105]°Ctyp 2 ns513
Fall time tFALLVDD = 5.0V, load = 20 pF; TA = [-40, 105]°Ctyp 1.3 ns513
I/O pin capacitance except TOSC and TWI pins CPINTA = [-40, 105]°C, VDD = [1.8, 5.5]Vtyp 3 pF513
I/O pin capacitance on TOSC pins CPINTA = [-40, 105]°C, VDD = [1.8, 5.5]Vtyp 5.5 pF513
Internal reference voltage INT11VVDD = [1.8V, 3.6V]; T = [0, 105]°C; based on characterizationmin -2 · max 2 %520
Internal reference voltage INT055V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°C; based on characterizationmin -3 · max 3 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25V, INT43VVDD = [1.8V, 5.5V]; T = [-40, 125]°C; based on characterizationmin -5 · max 5 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°C; based on characterizationmin -3 · max 3 %520
Supply voltage VDDADC; Temperature = -40°C to 125°C; DUTYCYC = 25%; CLKADC = 13 × fADCmin 1.8 · max 5.5 V520
θJA θJA14-pin SOICtyp 58 °C/W583
θJC θJC14-pin SOICtyp 26 °C/W583
Active power consumptionCLK_CPU = 20 MHz (OSC20M); VDD = 5V; T = 25°C; peripherals disabled and without I/O drivetyp 10.2 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 5V; T = 25°C; peripherals disabled and without I/O drivetyp 5.5 mA508
Active power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 3V; T = 25°C; peripherals disabled and without I/O drivetyp 3.1 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 5V; T = 25°C; peripherals disabled and without I/O drivetyp 3.2 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 3V; T = 25°C; peripherals disabled and without I/O drivetyp 1.8 mA508
Active power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 2V; T = 25°C; peripherals disabled and without I/O drivetyp 1.2 mA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 5V; T = 25°C; peripherals disabled and without I/O drivetyp 13.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 3V; T = 25°C; peripherals disabled and without I/O drivetyp 7.5 uA508
Active power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 2V; T = 25°C; peripherals disabled and without I/O drivetyp 5 uA508
Idle power consumptionCLK_CPU = 20 MHz (OSC20M); VDD = 5V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 4.3 · max 6.3 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 5V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 2.2 · max 3.1 mA508
Idle power consumptionCLK_CPU = 10 MHz (OSC20M div2); VDD = 3V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 1.1 · max 1.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 5V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 1.1 · max 1.6 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 3V; T = 25°C; peripherals disabled and without I/O drivetyp 0.6 · max 0.9 mA508
Idle power consumptionCLK_CPU = 5 MHz (OSC20M div4); VDD = 2V; T = 25°C; peripherals disabled and without I/O drivetyp 0.4 mA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 5V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 8.2 · max 20 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 3V; T = 25°C; peripherals disabled and without I/O drive; maximum based on characterizationtyp 4.2 · max 15 uA508
Idle power consumptionCLK_CPU = 32.768 kHz (OSCULP32K); VDD = 2V; T = 25°C; peripherals disabled and without I/O drivetyp 2.6 uA508
Standby power consumptionRTC running at 1.024 kHz from external XOSC32K (CL=7.5 pF); VDD = 3V; T = 25°Ctyp 0.69 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 25°Ctyp 0.71 · max 3 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 85°Cmax 6 uA508
Standby power consumptionRTC running at 1.024 kHz from internal OSCULP32K; VDD = 3V; T = 125°Cmax 8 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 25°Ctyp 0.1 · max 2 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 85°Cmax 5 uA508
Power-down/Standby power consumption are the same when all peripherals are stoppedAll peripherals stopped; VDD = 3V; T = 125°Cmax 7 uA508
Max. Recommended Baud RateUPDICLKDIV = 0x1 (16 MHz)max 0.9 Mbps469
Min. Recommended Baud RateUPDICLKDIV = 0x1 (16 MHz)min 0.3 kbps469
Max. Recommended Baud RateUPDICLKDIV = 0x2 (8 MHz)max 450 kbps469
Min. Recommended Baud RateUPDICLKDIV = 0x2 (8 MHz)min 0.15 kbps469
Max. Recommended Baud RateUPDICLKDIV = 0x3 (4 MHz) - Defaultmax 225 kbps469
Min. Recommended Baud RateUPDICLKDIV = 0x3 (4 MHz) - Defaultmin 0.075 kbps469
Max. Total ErrorData + Parity Bits = 9; Rslow = 96.39; Rfast = 104.76min -3.61 · max 4.76 %469
Recommended Max. RX ErrorData + Parity Bits = 9; Rslow = 96.39; Rfast = 104.76min -1.5 · max 1.5 %469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x1 (16 MHz)typ 6.15 ms469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x2 (8 MHz)typ 12.3 ms469
Recommended BREAK Character DurationUPDICLKDIV[1:0] = 0x3 (4 MHz) - Defaulttyp 24.6 ms469
Reset power consumptionReset line pulled down; VDD = 3V; 25°Ctyp 100 uA509
Start-up time from any Reset release twakeupVDD = 3V; T = 25°Ctyp 200 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 20 MHz; VDD = 5V; T = 25°Ctyp 1 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 10 MHz; VDD = 3V; T = 25°Ctyp 2 us509
Wake-up from Idle sleep mode twakeupOSC20M @ 5 MHz; VDD = 2V; T = 25°Ctyp 4 us509
Wake-up from Standby and Power-Down sleep mode twakeupVDD = 3V; T = 25°C; OSC20M system clocktyp 10 us509
BODContinuous; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 19 uA509
BODSampling @ 1 kHz; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 1 uA509
TCA16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idletyp 13 uA509
TCB16-bit count @ 1 MHz; VDD = 3V; T = 25°C; Idletyp 7.5 uA509
RTC16-bit count @ 32.768 kHz @ OSCULP32K; VDD = 3V; T = 25°C; Idletyp 1 uA509
WDT (including OSCULP32K)VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 1 uA510
OSC20MVDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 125 uA510
ACFast mode; CPU in Standby; VDD = 3V; T = 25°Ctyp 92 uA510
ACLow-Power mode; CPU in Standby; VDD = 3V; T = 25°Ctyp 45 uA510
ADC50 ksps; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 325 uA510
ADC100 ksps; VDD = 3V; T = 25°C; Idle; OSC20M at 1 MHztyp 340 uA510
XOSC32KCL = 7.5 pF; VDD = 3V; T = 25°C; Idletyp 0.5 uA510
OSCULP32KVDD = 3V; T = 25°C; Idletyp 0.5 uA510
USARTEnable @ 9600 Baud; VDD = 3V; T = 25°C; Idletyp 13 uA510
SPI (Master)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idletyp 2 uA510
TWI (Master)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idletyp 24 uA510
TWI (Slave)Enable @ 100 kHz; VDD = 3V; T = 25°C; Idletyp 17 uA510
Flash programmingErase Operation; VDD = 3V; T = 25°Ctyp 1.5 mA510
Flash programmingWrite Operation; VDD = 3V; T = 25°Ctyp 3 mA510
Power-on Slope SRONmax 100 V/ms510
POR threshold voltage on VDD falling VPORVDD falls/rises at 0.5 V/ms or slowermin 0.8 · max 1.6 V510
POR threshold voltage on VDD rising VPORVDD falls/rises at 0.5 V/ms or slowermin 1.4 · max 1.8 V510
BOD triggering level (falling/rising) VBODBODLEVEL7min 3.9 · typ 4.2 · max 4.5 V510
BOD triggering level (falling/rising) VBODBODLEVEL2min 2.4 · typ 2.6 · max 2.9 V510
BOD triggering level (falling/rising) VBODBODLEVEL0min 1.7 · typ 1.8 · max 2 V510
I/O pin capacitance on TWI pins CPINtyp 10 pF514
Pull-up resistor RPmin 20 · typ 35 · max 50 kΩ514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [1.8, 5.5]V; TA = [-40, 125]°Cmax 8 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [2.7, 5.5]V; TA = [-40, 125]°Cmax 16 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [4.5, 5.5]V; TA = [-40, 105]°Cmax 32 MHz514
CLK_TCD_SYNC maximum frequencies fCLK_TCD_SYNCVDD = [4.5, 5.5]V; TA = [-40, 125]°Cmax 20 MHz514
SCK clock frequency fSCKMastermax 10 MHz514
SCK period tSCKMastermin 100 ns514
SCK rise time tSCKRMastertyp 2.7 ns516
SCK fall time tSCKFMastertyp 2.7 ns516
MISO setup to SCK tMISMastertyp 10 ns516
MISO hold after SCK tMIHMastertyp 10 ns516
MOSI hold after SCK tMOHMastertyp 1 ns516
Slave SCK clock frequency fSSCKSlavemax 5 MHz516
SCK rise time tSSCKRSlavemax 1600 ns516
SCK fall time tSSCKFSlavemax 1600 ns516
MOSI setup to SCK tSISSlavemin 3 ns516
SS setup to SCK tSSSSlavemin 21 ns516
SS hold after SCK tSSHSlavemin 20 ns516
MISO setup to SCK tSOSSlavetyp 8 ns516
MISO hold after SCK tSOHSlavetyp 13 ns516
MISO setup after SS low tSOSSSlavetyp 11 ns516
MISO hold after SS low tSOSHSlavetyp 8 ns516
SCL clock frequency fSCLMaximum requires 10 MHz system clock, VDD = [2.7, 5.5]V and T = [-40, 105]°Cmin 0 · max 1000 kHz517
Output low voltage VOLIload = 3 mA, Normal mode, VDD > 2Vmax 0.4 V517
Low-level output current IOLfSCL ≤ 400 kHz, VOL = 0.4Vmin 3 mA517
Low-level output current IOLfSCL ≤ 1 MHz, VOL = 0.4Vmin 20 mA517
Capacitive load for each bus line CBfSCL ≤ 100 kHzmax 400 pF517
Capacitive load for each bus line CBfSCL ≤ 400 kHzmax 400 pF517
Capacitive load for each bus line CBfSCL ≤ 1 MHzmax 550 pF517
Rise time for both SDA and SCL tRfSCL ≤ 100 kHzmax 1000 ns517
Rise time for both SDA and SCL tRfSCL ≤ 400 kHzmin 20 · max 300 ns517
Rise time for both SDA and SCL tRfSCL ≤ 1 MHzmax 120 ns517
Output fall time from VIHmin to VILmax tOF10 pF < Capacitance of bus line < 400 pF; fSCL ≤ 400 kHzmax 250 ns517
Output fall time from VIHmin to VILmax tOF10 pF < Capacitance of bus line < 400 pF; fSCL ≤ 1 MHzmax 120 ns517
Spikes suppressed by Input filter tSPmin 0 · max 50 ns517
Input current for each I/O pin IL0.1×VDD < VI < 0.9×VDDmax 1 uA517
Capacitance for each I/O pin CImax 10 pF517
Internal reference voltage INT11VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -2 · max 2 %520
Internal reference voltage INT055V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -3 · max 3 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25V, INT43VVDD = [1.8V, 5.5V]; T = [-40, 125]°Cmin -5 · max 5 %520
Internal reference voltage INT055V, INT11V, INT15V, INT25VVDD = [1.8V, 3.6V]; T = [0, 105]°Cmin -3 · max 3 %520
Supply voltage VDDADCmin 1.8 · max 5.5 V520
Reference voltage VREFADC; REFSEL = Internal referencemin 0.55 V521
Reference voltage VREFADC; REFSEL = VDDmin 1.8 · max 5.5 V521
Input capacitance CINADC; SAMPCAP = 5 pFtyp 5 pF521
Input capacitance CINADC; SAMPCAP = 10 pFtyp 10 pF521
Input resistance RINADCtyp 14 kΩ521
Input voltage range VINADCmin 0 V521
Input bandwidth IBANDADC; 1.1V ≤ VREFmax 57.5 kHz521
Sample rate fADCADC; 1.1V ≤ VREFmin 15 · max 115 ksps521
Sample rate fADCADC; 1.1V ≤ VREF (8-bit resolution)min 15 · max 150 ksps521
Sample rate fADCADC; VREF = 0.55V (10 bits)min 7.5 · max 20 ksps521
Clock frequency CLKADCADC; VREF = 0.55V (10 bits)min 100 · max 260 kHz521
Clock frequency CLKADCADC; 1.1V ≤ VREF (10 bits)min 200 · max 1500 kHz521
Clock frequency CLKADCADC; 1.1V ≤ VREF (8-bit resolution); 50% duty cycle required above 1500 kHzmin 200 · max 2000 kHz521
Sampling time TsADCmin 2 · typ 2 · max 33 CLKADC cycles521
Conversion time (latency) TCONVADC; Sampling time = 2 CLKADCmin 8.7 · max 50 us521
Start-up time TSTARTADC; Internal VREFtyp 22 us521
Resolution RESADCtyp 10 bit521
Integral nonlinearity INLADC; REFSEL = INTERNAL; VREF = 0.55V; fADC = 7.7 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 15 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 77 kspstyp 1 LSb521
Integral nonlinearity INLADC; REFSEL = INTERNAL or VDD; 1.1V ≤ VREF; fADC = 115 kspstyp 1.2 LSb521
Conversion resolution TRES10 bitstyp 0.55 °C523
Conversion time tCONV1 MHz ADC clocktyp 13 us523
Supply voltage VDDDAC; supply must meet the VDD specification for the VREF level usedmin 1.8 · typ 3 · max 5.5 V523
Resistive external load RLoadDAC; VDD = 3Vmin 5 kΩ523
Capacitive external load CLoadDAC; VDD = 3Vmax 30 pF523
Output voltage range VOUTDAC; VDD = 3Vmin 0.2 V523
Output sink/source IOUTDAC; VDD = 3Vtyp 1 mA523
Maximum conversion rate fDACDAC; VDD = 3V; 0.55V ≤ VREF ≤ 2.5Vtyp 350 ksps523
Maximum conversion rate fDACDAC; VDD = 3V; VREF = 4.3Vtyp 270 ksps523
Resolution RESDACmax 8 bits523
Integral nonlinearity INLDAC; VDD = 3V; 0.55V ≤ VREF ≤ 4.3V; 5% to 95% rangemin -1.2 · typ 0.3 · max 1.2 LSb523
Differential nonlinearity DNLDAC; VDD = 3V; 0.55V ≤ VREF ≤ 4.3V; 5% to 95% rangemin -1 · typ 0.25 · max 1 LSb523
Offset error EOFFDAC; VDD = 3V; 0.55V ≤ VREF ≤ 1.5V; includes output buffer offsetmin -25 · typ -3 · max 20 mV523
Offset error EOFFDAC; VDD = 3V; VREF = 2.5V; includes output buffer offsetmin -30 · typ -6 · max 10 mV523
Offset error EOFFDAC; VDD = 3V; VREF = 4.3V; includes output buffer offsetmin -40 · typ -10 · max 0 mV523
Gain error EGAINDAC; VDD = 3V; 0.55V ≤ VREF ≤ 4.3V; VREF accuracy includedmin -10 · typ -1 · max 10 LSb523
Junction-to-ambient thermal resistance θJA14-pin SOICtyp 58 °C/W583
Junction-to-case thermal resistance θJC14-pin SOICtyp 26 °C/W583

Open-source boards using it

60See all 60
  • 4 layers67 × 98 mmSJ-201-R6, the printed circuit board in 3D

    SJ-201-R6

    MycroftAI/hardware-mycroft-mark-II

    Mycroft's Mark II Rpi mechanical, electrical and industrial designs

    235 parts113
  • 2 layers23.7 × 25.5 mmMalenki, the printed circuit board in 3D

    Malenki

    MarkR42/malenki-esc

    A small electronic speed controller for e.g. tiny fighting robots or other rc models

    30 parts7
  • 2 layers157.5 × 81.3 mmCollectorPanel, the printed circuit board in 3D

    CollectorPanel

    tjhiker/Personal-MiniBadges-2025

    My Personal MiniBadges used at SAINTCON 2025

    25 parts7
  • 2 layers179.1 × 67.9 mmControl Board, the printed circuit board in 3D

    Control Board

    Alan-JH/PCB-Heater

    Reflow hotplate PCB design

    77 parts6
  • 2 layers41 × 41 mmRid, the printed circuit board in 3D

    Rid

    swr06/LED-Wearable

    LED Wearable that displays patterns, based on ATTiny1614

    12 parts5MIT
  • 2 layers33 × 23.9 mmESPTiny1614, the printed circuit board in 3D

    ESPTiny1614

    tomtor/ESPTiny

    KiCad ATtiny84/x14/x02 (SMD) and ESP-01 (ESP 8266) PCB boards

    24 parts4GPL-3.0
  • 2 layers30.5 × 15.2 mmAvr attiny1614-mini, the printed circuit board in 3D

    Avr attiny1614-mini

    vladbelous/avr-attiny1614-mini

    AVR attiny1614 (tinyAVR 1-series) mini board

    26 parts4
  • 2 layers53.5 × 26.5 mmSB Pixel Count, the printed circuit board in 3D

    SB Pixel Count

    computergeek1507/SB_Pixel_Count

    SB Pixel Counter

    23 parts3

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATTINY1614-SSN?

Yes. The symbol is MCU_Microchip_ATtiny:ATtiny1614-SS and the footprint Package_SO:SOIC-14_3.9x8.7mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATTINY1614-SSN?

SOIC-14, with 14 pins. Its footprint is drawn on this page.

Where is the ATTINY1614-SSN datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATTINY1614-SSN?

JLCPCB lists it as part C481364, with 185 in stock; the sellers' links on this page open their listings.

What can replace the ATTINY1614-SSN?

Parts like it in the library: the PY32F002BD15S6TU by PUYA, the PIC16F1503-I/SL by Microchip Technology, the PIC16F1824-I/SL by Microchip Technology and the PIC16F676-I/SL by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATTINY1614-SSN?

60 boards in 46 repositories on GitHub; the most starred are listed on this page, with their KiCad files.