
AT24C64D-SSHM-T
Microchip TechnologyExtended
-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 5ms 64Kbit Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHS
- Part id
- microchip/AT24C64D-SSHM-T
- Category
- EEPROM
- Package
- SOIC-8
- Pins
- 8
- In stock
- 34,591 at JLCPCB (C6487)
- Used on
- 11 open-source boards
Overview
The AT24C64D-SSHM-T is an EEPROM made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 5ms 64Kbit Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHS.
PCBKit's library has its KiCad symbol (Logic:AT24C64D-SSH, from CERN's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 34,591 are in stock at JLCPCB (part C6487). 11 open-source boards in 11 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 1.7 V · VCC, recommended operating min · p. 4
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 4
- Supply, absolute maximum
- 6.25 V · VCC, absolute maximum operating voltage · p. 2
- Works from
- -40 °C · Industrial operating ambient min · p. 4
- Works up to
- 85 °C · Industrial operating ambient max · p. 4
- Takes working
- 400 µA · VCC read current typical, 5.0 V, 400 kHz · p. 4
- Takes at most
- 3 mA · VCC write current max, 5.0 V, 400 kHz · p. 4
- Takes asleep
- 1 µA · VCC standby current max, 1.7 V, VIN = VCC or VSS · p. 4
- Takes asleep
- 6 µA · VCC standby current max, 5.0 V, VIN = VCC or VSS · p. 4
- A pin gives at most
- 5 mA · DC output current absolute max · p. 2
- Data rate, most
- 1 Mbit/s · Serial clock max, VCC = 2.5 V or 5.0 V · p. 5
What it is and has
10- EEPROM
- 64 Kbit, organized as 8,192 x 8 · p. 1
- Interface
- I2C-compatible 2-Wire serial · p. 1
- Interface clock
- 400 kHz at 1.7 V; 1 MHz at 2.5 V, 2.7 V, 5.0 V · p. 1
- Input filtering
- Schmitt Trigger, filtered inputs for noise suppression · p. 1
- Write protection
- Hardware Write Protect pin · p. 1
- Page Write
- 32 bytes · p. 1
- Partial Page Writes
- Allowed · p. 1
- Write cycle
- Self-timed, 5 ms maximum · p. 1
- Endurance
- 1,000,000 write cycles · p. 1
- Data retention
- 100 years · p. 1
Around it
2- res 10k or less
- between A0/A1/A2 and VCC; Optional address input pull-up; connect each address input to a known state. · p. 3
- res 10k or less
- between WP and VCC; Optional Write Protect pull-up; connect WP to a known state. · p. 3
Specifications
47| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Operating Temperature | Absolute maximum stress rating | min -55 · max 125 °C | 2 |
| Storage Temperature | min -65 · max 150 °C | 2 | |
| Voltage on any pin with respect to ground | min -1 · max 7 V | 2 | |
| Maximum Operating Voltage | max 6.25 V | 2 | |
| DC Output Current | max 5 mA | 2 | |
| Input/Output Capacitance (SDA) CI/O | TA = 25°C, f = 1.0MHz, VCC = 5.5V; VI/O = 0V | max 8 pF | 4 |
| Input Capacitance (A0, A1, A2, and SCL) CIN | TA = 25°C, f = 1.0MHz, VCC = 5.5V; VIN = 0V | max 6 pF | 4 |
| Supply Voltage VCC1 | TAI = -40°C to +85°C | min 1.7 · max 5.5 V | 4 |
| Supply Current ICC1 | VCC = 5.0V; Read at 400kHz; TAI = -40°C to +85°C | typ 0.4 · max 1 mA | 4 |
| Supply Current ICC2 | VCC = 5.0V; Write at 400kHz; TAI = -40°C to +85°C | typ 2 · max 3 mA | 4 |
| Standby Current ISB1 | VCC = 1.7V; VIN = VCC or VSS; TAI = -40°C to +85°C | max 1 uA | 4 |
| Standby Current ISB1 | VCC = 5.0V; VIN = VCC or VSS; TAI = -40°C to +85°C | max 6 uA | 4 |
| Input Leakage Current VCC = 5.0V ILI | VIN = VCC or VSS; TAI = -40°C to +85°C | typ 0.1 · max 3 uA | 4 |
| Output Leakage Current VCC = 5.0V ILO | VOUT = VCC or VSS; TAI = -40°C to +85°C | typ 0.05 · max 3 uA | 4 |
| Input Low Level(1) VIL | TAI = -40°C to +85°C, VCC = 1.7V to 5.5V; max = VCC x 0.3; minimum is reference only and not tested | min -0.6 V | 4 |
| Output Low Level VOL1 | VCC = 1.7V; IOL = 0.15mA; TAI = -40°C to +85°C | max 0.2 V | 4 |
| Output Low Level VOL2 | VCC = 3.0V; IOL = 2.1mA; TAI = -40°C to +85°C | max 0.4 V | 4 |
| Clock Frequency, SCL fSCL | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | max 400 kHz | 5 |
| Clock Frequency, SCL fSCL | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | max 1000 kHz | 5 |
| Clock Pulse Width Low tLOW | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 1300 ns | 5 |
| Clock Pulse Width Low tLOW | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 400 ns | 5 |
| Clock Pulse Width High tHIGH | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 600 ns | 5 |
| Clock Pulse Width High tHIGH | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 400 ns | 5 |
| Noise Suppression Time tI | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF; characterized, not 100% tested | max 100 ns | 5 |
| Noise Suppression Time tI | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF; characterized, not 100% tested | max 50 ns | 5 |
| Clock Low to Data Out Valid tAA | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 50 · max 900 ns | 5 |
| Clock Low to Data Out Valid tAA | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 50 · max 550 ns | 5 |
| Time the bus must be free before a new transmission can start(1) tBUF | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 1300 ns | 5 |
| Time the bus must be free before a new transmission can start(1) tBUF | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 500 ns | 5 |
| Start Hold Time tHD.STA | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 600 ns | 5 |
| Start Hold Time tHD.STA | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 250 ns | 5 |
| Start Set-up Time tSU.STA | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 600 ns | 5 |
| Start Set-up Time tSU.STA | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 250 ns | 5 |
| Data In Hold Time tHD.DAT | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 0 ns | 5 |
| Data In Hold Time tHD.DAT | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 0 ns | 5 |
| Data In Set-up Time tSU.DAT | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 100 ns | 5 |
| Data In Set-up Time tSU.DAT | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 100 ns | 5 |
| Inputs Rise Time(1) tR | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | max 300 ns | 5 |
| Inputs Rise Time(1) tR | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | max 300 ns | 5 |
| Inputs Fall Time tF | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF; characterized, not 100% tested | max 300 ns | 5 |
| Inputs Fall Time tF | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF; characterized, not 100% tested | max 100 ns | 5 |
| Stop Set-up Time tSU.STO | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 600 ns | 5 |
| Stop Set-up Time tSU.STO | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 250 ns | 5 |
| Data Out Hold Time tDH | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | min 50 ns | 5 |
| Data Out Hold Time tDH | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | min 50 ns | 5 |
| Write Cycle Time tWR | VCC = 1.7V; TAI = −40°C to +85°C; CL = 100pF | max 5 ms | 5 |
| Write Cycle Time tWR | VCC = 2.5V, 5.0V; TAI = −40°C to +85°C; CL = 100pF | max 5 ms | 5 |
Pins, by the datasheet
8- 1 A0
- Device address input; connect to GND or VCC to select the address. · p. 2
- 2 A1
- Device address input; connect to GND or VCC to select the address. · p. 2
- 3 A2
- Device address input; connect to GND or VCC to select the address. · p. 2
- 4 GND
- Ground. · p. 2
- 5 SDA
- Bidirectional serial data, driven open drain. · p. 2
- 6 SCL
- Serial clock input; positive edges clock data in and negative edges clock data out. · p. 2
- 7 WP
- Write protect; connect to GND for normal writes or VCC to inhibit all writes. · p. 2
- 8 VCC
- Device power supply. · p. 2
- 8 layers110 × 181.8 mm

- 6 layers84 × 69 mm

- 2 layers100 × 100 mm

Temp pro
CrafterSteve/ESP32_Temp_Con
An temperture control device, based on ESP32. With custom PCB board, it can fit an ESP32-DevKit as controller, DAC and ADC is done on board, as well as, a 5 to +-12v power supply..
134 parts - 4 layers64.6 × 55.2 mm

Whisker
HeyPCB/whisker
Drop-in controller for Petoi's Nybble robot cat running the stock OpenCat firmware: ATmega328P, PCA9685, MPU-6050, USB-C, 3 A buck, protected battery input. 4-layer KiCad 10 board plus printed cradle.
118 partsCERN-OHL-S-2.0 - 4 layers100 × 60 mm

Ephys test module-64
open-ephys/ephys-test-module-hirose-df40-64-chan
Test module for headstages using Hirose DF40C-70DP-0.4V(51) electrode interface
25 parts - 2 layers100 × 60 mm

Ephys test module molc-64-chan
open-ephys/ephys-test-module-molc-64-chan
Test module for headstages compatible with the NanoZ/MOLC-110-01-S-Q_1 electrode interface
20 parts - 2 layers106.9 × 69 mm

Ephys test module molex-504070-32
open-ephys/ephys-test-module-molex-504070-32-chan
Test module for headstages using Molex 504070 electrode interface
19 parts - 2 layers100 × 60 mm

Ephys test module-32
open-ephys/ephys-test-module-omnetics-a79026-001-32-chan
Test module for headstages using Omnetics A79026-001 electrode interface
16 parts
Parts like it
8M24C64-RMN6TP
SOIC-8-40℃~+85℃ 1.8V~5.5V 1MHz 2.5mA 200 Years 3uA 4,000,000 Cycles 5ms 64Kbit Hardware write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROMM24512-RMN6TP
SOIC-8-40℃~+85℃ 1.8V~5.5V 1MHz 1uA 200 Years 4,000,000 Cycles 512Kbit 5mA 5ms Hardware write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROMAT24C08C-SSHM-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 5ms 8Kbit I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMAT24C256C-SSHL-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 1MHz 256Kbit 40 Years 5ms Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMAT24C512C-SSHD-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1MHz 2.5V~5.5V 40 Years 512Kbit 5ms Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMCAT24C256WI-GT3
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 256Kbit 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHSonsemiEEPROMAT24C128C-SSHM-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 128Kbit 1MHz 3mA 450ns、900ns 5ms 6uA Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMBL24C256A-PARC
SOP-8L-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 256Kbit 3ms I2C SOP-8 EEPROM ROHSBLEEPROM
Questions
Is there a KiCad symbol and footprint for the AT24C64D-SSHM-T?
Yes. The symbol is Logic:AT24C64D-SSH and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the AT24C64D-SSHM-T?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the AT24C64D-SSHM-T datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the AT24C64D-SSHM-T?
JLCPCB lists it as part C6487, with 34,591 in stock; the sellers' links on this page open their listings.
What can replace the AT24C64D-SSHM-T?
Parts like it in the library: the M24C64-RMN6TP by STMicroelectronics, the M24512-RMN6TP by STMicroelectronics, the AT24C08C-SSHM-T by Microchip Technology and the AT24C256C-SSHL-T by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the AT24C64D-SSHM-T?
11 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.