Skip to the content
12345678

M24C64-RMN6TP

STMicroelectronicsJLCPCB preferred

-40℃~+85℃ 1.8V~5.5V 1MHz 2.5mA 200 Years 3uA 4,000,000 Cycles 5ms 64Kbit Hardware write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHS

Part id
st/M24C64-RMN6TP
Category
EEPROM
Package
SOIC-8
Pins
8
In stock
208,768 at JLCPCB (C79988)
Used on
17 open-source boards

Overview

The M24C64-RMN6TP is an EEPROM made by STMicroelectronics in a SOIC-8 package with 8 pins. -40℃~+85℃ 1.8V~5.5V 1MHz 2.5mA 200 Years 3uA 4,000,000 Cycles 5ms 64Kbit Hardware write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHS.

PCBKit's library has its KiCad symbol (JLCPCB-Memory:64Kbit, I2C, from Cdfer) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 208,768 are in stock at JLCPCB (part C79988). 17 open-source boards in 14 repositories on GitHub use it.

Symbol

1A02A13A24VSS5SDA6SCL7#WC8VCC
JLCPCB-Memory:64Kbit, I2CFrom Cdfer

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

9
Supply, least
1.8 V · VCC, recommended operating min · p. 25
Supply, most
5.5 V · VCC, recommended operating max · p. 25
Supply, absolute maximum
6.5 V · VCC, absolute max · p. 24
Works from
-40 °C · Ambient operating temperature min · p. 25
Works up to
85 °C · Ambient operating temperature max · p. 25
Takes working
800 µA · VCC, Read current max at 1.8 V, 400 kHz · p. 28
Takes at most
2.5 mA · VCC, Read current max at 1 MHz, qualified devices · p. 28
Takes asleep
1 µA · VCC, Standby supply current max at 1.8 V · p. 28
A pin gives at most
5 mA · SDA, DC output sink current absolute max · p. 24

What it is and has

10
EEPROM
64 Kbit (8 Kbyte) · p. 1
Page size
32 byte · p. 1
Read modes
Random and sequential · p. 1
Write protection
Whole memory array · p. 1
Protection
Enhanced ESD/Latch-Up protection · p. 1
Byte Write
Within 5 ms · p. 1
Page Write
Within 5 ms · p. 1
Power-on reset
Included to prevent inadvertent writes during power-up · p. 10
EEPROM memory
64 Kbit (8 Kbyte) · p. 1
Interface
I2C serial access · p. 47

Around it

1
cap 10 nF to 100 nF
between VCC and VSS; Supply decoupling; place close to the VCC/VSS package pins. · p. 10

Specifications

68
ParameterConditionsAs printedPage
Ambient operating temperaturemin -40 · max 130 °C24
Storage temperature TSTGmin -65 · max 150 °C24
DC output current (SDA = 0) IOLmax 5 mA24
Input or output range VIOmin -0.5 · max 6.5 V24
Supply voltage VCCmin -0.5 · max 6.5 V24
Electrostatic pulse (Human Body model) VESDNote (4): 4000 V for process letters K and P.max 3000 V24
Supply voltage VCCM24C64-Rmin 1.8 · max 5.5 V25
Ambient operating temperature TAM24C64-Rmin -40 · max 85 °C25
Operating clock frequency fCM24C64-R; note (1): 400 kHz for process letter P.max 1 MHz25
SCL input rise/fall time, SDA input fall timemax 50 ns25
Input capacitance (SDA) CINCharacterized only, not tested in production.max 8 pF26
Input capacitance (other pins) CINCharacterized only, not tested in production.max 6 pF26
Input impedance (E2, E1, E0, WC) ZLVIN < 0.3 VCC; memory selected after a Start condition; characterized only.min 30 kΩ26
Input impedance (E2, E1, E0, WC) ZHVIN > 0.7 VCC; memory selected after a Start condition; characterized only.min 500 kΩ26
Data retentionTA = 55 °C; process letter K or T.min 200 Year26
Input leakage current (E0, E1, E2, SCL, SDA) ILIVIN = VSS or VCC, device in Standby mode; magnitude limit ±2 uA.max 2 uA28
Output leakage current ILOSDA in Hi-Z, external voltage applied on SDA: VSS or VCC; magnitude limit ±2 uA.max 2 uA28
Supply current (Read) ICCVCC = 1.8 V, fc= 400 kHzmax 0.8 mA28
Supply current (Read) ICCfc= 1 MHz; only devices operating at fC max = 1 MHz.max 2.5 mA28
Supply current (Write) ICC0During tW; 1.8 V ≤ VCC 2.5 V as printed; process letter K or T; characterized value.max 1.5 mA28
Standby supply current ICC1Device not selected, VIN = VSS or VCC, VCC = 1.8 Vmax 1 uA28
Input low voltage (SCL, SDA) VIL1.8 V ≤ VCC < 2.5 V; maximum 0.25 VCC; Ei inputs tied to Vss.min -0.45 V28
Input high voltage (SCL, SDA) VIH1.8 V ≤ VCC < 2.5 V; minimum 0.75 VCC.max 6.5 V28
Output low voltage VOLIOL = 1 mA, VCC = 1.8 V; IOL = 0.7 mA for process letter P.max 0.2 V28
Input leakage current (SCL, SDA, E2, E1, E0) ILIApplicable to M24C64-R at 2.5 V < Vcc < 5.5 V and -40 °C < TA < +85 °C; VIN = VSS or VCC, Standby mode; magnitude limit ±2 uA.max 2 uA27
Output leakage current ILOApplicable to M24C64-R at 2.5 V < Vcc < 5.5 V and -40 °C < TA < +85 °C; SDA in Hi-Z, external voltage VSS or VCC; magnitude limit ±2 uA.max 2 uA27
Supply current (Read) ICCApplicable to M24C64-R; 2.5 V < VCC < 5.5 V, fc = 400 kHz, rise/fall time < 50 ns.max 2 mA27
Supply current (Read) ICCApplicable to M24C64-R; 2.5 V < VCC < 5.5 V, fc = 1 MHz, rise/fall time < 50 ns; process letter K or T.max 2.5 mA27
Supply current (Write) ICC0Applicable to M24C64-R above 2.5 V; during tW, 2.5 V ≤ VCC ≤ 5.5 V; characterized value.max 2.5 mA27
Standby supply current ICC1Applicable to M24C64-R per Table 15 note (1); device not selected, VIN = VSS or VCC, VCC = 2.5 V.max 2 uA27
Standby supply current ICC1Applicable to M24C64-R per Table 15 note (1); device not selected, VIN = VSS or VCC, VCC = 5.5 V; previous process P products: 5 uA.max 3 uA27
Input low voltage (SCL, SDA, WC, E2, E1, E0) VILApplicable to M24C64-R at 2.5 V < Vcc < 5.5 V and -40 °C < TA < +85 °C; maximum 0.3 VCC; Ei inputs tied to Vss.min -0.45 V27
Input high voltage (SCL, SDA) VIHApplicable to M24C64-R at 2.5 V < Vcc < 5.5 V and -40 °C < TA < +85 °C; minimum 0.7 VCC.max 6.5 V27
Output low voltage VOLApplicable to M24C64-R per Table 15 note (1); IOL = 2.1 mA, VCC = 2.5 V.max 0.4 V27
Output low voltage VOLApplicable to M24C64-R per Table 15 note (1); IOL = 3 mA, VCC = 5.5 V.max 0.4 V27
Clock frequency fCmax 400 kHz30
Clock pulse width high tCHCLmin 600 ns30
Clock pulse width low tCLCHmin 1300 ns30
SDA (out) fall time tQL1QL2Characterized only; minimum with CL = 10 pF.min 20 · max 300 ns30
Data in set up time tDXCHmin 100 ns30
Data in hold time tCLDXmin 0 ns30
Data out hold time tCLQXmin 50 ns30
Clock low to next data valid (access time) tCLQVRbus × Cbus within Figure 15 limits.max 900 ns30
Start condition setup time tCHDLmin 600 ns30
Start condition hold time tDLCLmin 600 ns30
Stop condition set up time tCHDHmin 600 ns30
Time between Stop condition and next Start condition tDHDLmin 1300 ns30
WC set up time (before the Start condition) tWLDLWC=0 to enable WRITE; characterized only.min 0 us30
WC hold time (after the Stop condition) tDHWHWC=0 to enable WRITE; characterized only.min 1 us30
Internal Write cycle duration tWmax 5 ms30
Pulse width ignored (input filter on SCL and SDA) - single glitch tNSCharacterized only.max 50 ns30
Clock frequency fCOnly process letter K or T, qualified at 1 MHz.min 0 · max 1 MHz31
Clock pulse width high tCHCLOnly process letter K or T.min 260 ns31
Clock pulse width low tCLCHOnly process letter K or T.min 500 ns31
SDA (out) fall time tQL1QL2Only process letter K or T; characterized only; minimum with CL = 10 pF.min 20 ns31
SDA (out) fall time tQL1QL2Only process letter K or T; characterized only; maximum on continuation line.max 120 ns31
Data in setup time tDXCHOnly process letter K or T.min 50 ns31
Data in hold time tCLDXOnly process letter K or T.min 0 ns31
Data out hold time tCLQXOnly process letter K or T.min 50 ns31
Clock low to next data valid (access time) tCLQVOnly process letter K or T; Rbus × Cbus within Figure 16 limits.max 450 ns31
Start condition setup time tCHDLOnly process letter K or T.min 250 ns31
Start condition hold time tDLCLOnly process letter K or T.min 250 ns31
Stop condition setup time tCHDHOnly process letter K or T.min 250 ns31
Time between Stop condition and next Start condition tDHDLOnly process letter K or T.min 500 ns31
WC set up time (before the Start condition) tWLDLOnly process letter K or T; WC=0 to enable WRITE; characterized only.min 0 us31
WC hold time (after the Stop condition) tDHWHOnly process letter K or T; WC=0 to enable WRITE; characterized only.min 1 us31
Write time tWOnly process letter K or T.max 5 ms31
Pulse width ignored (input filter on SCL and SDA) tNSOnly process letter K or T; characterized only.max 50 ns31

Open-source boards using it

17See all 17
  • 2 layers106 × 55 mmIoboard 4ports isolated, the printed circuit board in 3D

    Ioboard 4ports isolated

    OpenLightingProject/rp2040-dmxsun

    RP2040-based USB DMX dongle with integrated web server

    60 parts128Apache-2.0
  • 2 layers139 × 113.5 mmEmber, the printed circuit board in 3D

    Ember

    kenyoshizoe/ember

    32Key Hall Effect Keyboard for Gaming

    112 parts36MIT
  • 4 layers80 × 50.5 mmLoeti, the printed circuit board in 3D

    Loeti

    elagil/loeti

    Soldering equipment for JBC irons

    110 parts5
  • 2 layers52 × 36 mmCyphalPicoBase CAN, the printed circuit board in 3D

    CyphalPicoBase CAN

    generationmake/CyphalPicoBase-CAN

    Board for the Raspberry Pi Pico to connect via CAN using OpenCyphal and UCANPHY Micro

    62 parts5CERN-OHL-W-2.0
  • 4 layers60 × 73.5 mmAnthracite bottom, the printed circuit board in 3D

    Anthracite bottom

    trope-oshw/anthracite

    MIDI-controllable fuzz pedal: open hardware (CERN-OHL-S-2.0), firmware (GPL-3.0-or-later)

    224 parts5CERN-OHL-S-2.0
  • 4 layers243.8 × 243.8 mmTangenta, the printed circuit board in 3D

    Tangenta

    vmetodiev/tangenta

    Micro ATX motherboard for Toradex Verdin iMX8M Mini

    577 parts5
  • 4 layers25 × 25 mmLaserCAN Board, the printed circuit board in 3D

    LaserCAN Board

    GrappleRobotics/LaserCAN

    59 parts3GPL-3.0
  • 4 layers85 × 54 mmIntegrated motor controller, the printed circuit board in 3D

    Integrated motor controller

    kgieselman/integrated_motor_controller_pcb

    Integrated Motor Controller for a robotics competion hosted by my work. The competitions changes each year so this board is flexible and contains mutliple headers for expanding to daughter boards.

    150 partsCERN-OHL-S-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the M24C64-RMN6TP?

Yes. The symbol is JLCPCB-Memory:64Kbit, I2C and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the M24C64-RMN6TP?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the M24C64-RMN6TP datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the M24C64-RMN6TP?

JLCPCB lists it as part C79988, with 208,768 in stock; the sellers' links on this page open their listings.

What can replace the M24C64-RMN6TP?

Parts like it in the library: the M24512-RMN6TP by STMicroelectronics, the AT24C08C-SSHM-T by Microchip Technology, the AT24C256C-SSHL-T by Microchip Technology and the AT24C512C-SSHD-T by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the M24C64-RMN6TP?

17 boards in 14 repositories on GitHub; the most starred are listed on this page, with their KiCad files.