4 layers60 × 35 mm
Slug v1.0
rumbletech/Slug_v1.0
Slug ( Slog/Serial Logger ) is an open source firmware and an open source hardware project , it implements logging of serial buses like USART,I2C,SPI to an SD Card.
78 parts1MIT
Open-source KiCad boards
48 match “SL-RU”Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.
- 4 layers78.7 × 63.5 mm
Hdmi trigger interface
ruffner/MojoV3_HDMI_Interface
FPGA SLI controller with dual HDMI and Basler machine vision camera trigger interface PCB
19 parts4 - 4 layers60 × 25 mm
- 4 layers85 × 25 mm
- 4 layers85 × 67 mm
- 4 layers90 × 76.6 mm
Micro core
quintinbannink42/micro-core
Core EFI Micro Core — Hellen-One rusEFI ECU, 35-way AMPSEAL, vertical header
49 parts - 4 layers84 × 56.5 mm
- 4 layers63.5 × 33 mm
Zx50 SwitchInterposer
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
7 parts - 4 layers133.5 × 68.8 mm
Zx50 FrontPanelCard
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
23 parts - 4 layers133.5 × 68.8 mm
Zx50 FrontPanelCard
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
22 parts - 4 layers210.8 × 137.2 mm
Zx50 Backplane RevD
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
75 parts - 4 layers133.5 × 100.3 mm
Zx50 Cpu
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
26 parts - 4 layers132.1 × 81.9 mm
Zx50 Serial
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
25 parts - 4 layers123.4 × 129.8 mm
Zx50 MemoryCard RevA
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
53 parts - 4 layers38.5 × 73.5 mm
PtSolar
custom-ds/ptSolar
Under the hood, the ptSolar runs on the same Microchip ATMega328p microcontroller that the other trackers have been using for years, although this board runs at a lower 3.3 volt level, and a slower 8MHz clock speed.
70 partsGPL-3.0 - 4 layers50.2 × 69.8 mm
Zx50 Clock Mezzanine RevC
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
40 parts - 4 layers115 × 55 mm
Roamr motors
uw-roamr/roamr
turn your phone into a robot running SLAM with two motors, two control boards, and a bluetooth chip
110 parts6 - 4 layers133.5 × 100.3 mm
Zx50 Cpu RevB
mmosko/Zx50
This is the primary CPU board for the Zx50 8-slot passive backplane system. It hosts the Z80 microprocessor (running at 5 MHz to 10 MHz) and acts as the master controller for the primary bus.
38 parts - 4 layers290 × 215 mm
- 4 layers100 × 120 mm
Micromouse pcb
MukeshSethy/micromouse-runner
This is my repo for the first version of full size micromouse development.
184 parts - 4 layers100 × 70 mm
Data port x6
kartben/hw-testing-rack
3D-printed, tilted test shelf for 16 dev boards: sliding drawers, per-bay ESP32-S3 running Zephyr (USB/IP, power switching, metering), KiCad PCBs, OpenSCAD parts, BOM and an interactive 3D viewer
187 parts - 4 layers34 × 48 mm
- 4 layers145.5 × 64 mm
Muffin
JunOllyLi/TX_PCB
NOTE: the latest PCB had been manufactured was v2.0. But it had the Gimbal ZH-connector reversed. The schematics and PCB drawing had been updated to v2.1 to fix that. But v2.1 had not been really manufactured yet.
138 parts17 - 4 layers125.7 × 76.5 mm
UGC Main
HandHeldLegend/GC-Ultimate
The 3D shell, buttons, and other associated models are licensed under a Creative Commons Attribution 4.0 International License .
128 parts62