Open-source KiCad boards

39 match “Greg-R”

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

2 layers150 × 8 mm
Gregdavill cap sense flex rx
oomlout/oomlout_oomp_project_bot_v_2

10 parts
2 layers22.8 × 20.3 mm
Gregdavill icebreaker pmod qspi ram
oomlout/oomlout_oomp_project_bot_v_2

6 parts
2 layers99.6 × 99.9 mm
Magloop pico
Greg-R/magloop_pico_pcb
Design and fabrication files the Magnetic Loop Antenna Controller printed circuit board.
102 parts1GPL-3.0
2 layers99.6 × 99.9 mm
Magloop pico
Greg-R/magloop_pico_pcb_2
Design and fabrication files the Magnetic Loop Antenna Controller printed circuit board.
101 parts1GPL-3.0
2 layers100 × 75 mm
Qse2
Greg-R/qse2
The documentation for this design is located here:
82 parts1GPL-3.0
2 layers166.1 × 30 mm
Rear Logics Custom Droid
greghulette/KiCad-Files-Public

274 parts2
2 layers28.6 × 30 mm
Esp daikin r1p1
gregdavill/daikin-esp
ESP32-C3 hardware to connect to a Daikin ducted A/C system. enabling WiFi control in Home Assistant.
37 parts29
2 layers30 × 30 mm
Hb bob r1p0
gregdavill/daikin-esp
ESP32-C3 hardware to connect to a Daikin ducted A/C system. enabling WiFi control in Home Assistant.
67 parts29
2 layers69 × 36 mm
Dinky Charge Regulator
Gregification/BeeMS
Battery Management System
10 parts5MIT
2 layers80 × 20 mm
Gregdavill ledmatrixdual ledmatrixdual
oomlout/oomlout_oomp_project_bot_v_2

46 parts
2 layers30 × 61 mm
Gregdavill clock controller clockcontroller
oomlout/oomlout_oomp_project_bot_v_2

49 parts
2 layers34.5 × 22 mm
Gregdavill fumecube ctrl esp ctrl
oomlout/oomlout_oomp_project_bot_v_2

26 parts
2 layers18 × 20.3 mm
Gregdavill icebreaker pmod ibp tristate led
oomlout/oomlout_oomp_project_bot_v_2

34 parts
2 layers50.8 × 77.5 mm
Gregdavill orangecrab test orangecrab test
oomlout/oomlout_oomp_project_bot_v_2

66 parts
2 layers50.8 × 22.9 mm
Gregdavill upythonfeatherlora upythonfeatherlora
oomlout/oomlout_oomp_project_bot_v_2

14 parts
2 layers44.2 × 83.8 mm
PlaneController
gregora/Arduino-RC-Plane
An RC airplane, controlled by a custom flight controller based on Arduino Nano.
17 parts
2 layers100 × 75 mm
Sousvide
gregorv/sousvide
Hardware and software for an ATmega8 based Sous-Vide temperature controller
66 partsGPL-3.0
2 layers76.2 × 76.2 mm
Speaker
gregory-chekler/Volume-Adjusting-Speaker-PCB
The circuit takes in a signal from an audio jack, that is of a frequency from about 40 Hz to 22 kHz (the range of human hearing). The LM 378 is supplied with 9 volts and the gain is at most 200 times.
12 parts
2 layers200 × 80 mm
Oal psu
gregose/oal-psu
TSP7A47-based power supply
68 parts
2 layers68.6 × 53.3 mm
Capteur Graphite
MOSH-Insa-Toulouse/2024-2025-4GP-GregoryBibiloni-GuillaumeBarth
Projet du capteur graphite "low tech" des 4GPs
25 partsGPL-3.0
2 layers347 × 156.5 mm
OF1 v1
GregTurbo/Open-Frame1
An open-source rectangle hardware project for smash, prioritizing ease of assembly and cost
68 parts120GPL-3.0
2 layers319.7 × 58.4 mm
Mini Orion TEM
Gregification/BeeMS
Battery Management System
170 parts5MIT
2 layers50 × 100 mm
Computy
gregora/Computy
Flight computer based on STM32 microcontroller
47 parts2
2 layers80 × 20 mm
LedMatrixDual
gregdavill/ledMatrixDual

35 parts1