
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

BB-8 1:1 Blender model, engineering validation, assembly guide, and D-O public resource map
Stage19 dual permissive gate is an open-source printed circuit board by zhangyinxina-ui, from the zhangyinxina-ui/bb8-do-assembly-guide repository on GitHub. It is a 2-layer board of 50 × 35 mm with 38 parts on 21 nets, routed with 1,614 tracks and 54 vias.
It is built around the SN74LVC2G08DCU, VO617A-4 and 1N4148W. Its parts include 13 resistors, 5 ICs, 5 connectors, 3 capacitors and 2 diodes. It belongs with the robots and motor control boards of this library.
This package replaces the Stage-18 empty gate-board placeholder with a reviewable electrical contract, deterministic KiCad 10 schematic and a real 50 × 35 mm two-layer routed PCB. KiCad 10.0.4 reports 0 ERC violations, 0 PCB DRC violations and 0 unconnected items. The 34 electrical references, 91 pin assignments and 21 named nets match the canonical CSV; the PCB adds four contracted 3.2 mm M3 NPTH mounting holes. It is deliberately not a fabrication release: independent schematic/layout peer review, intentional Gerber/drill review, fabrication, continuity, power-up and bench waveforms remain absent.
flowchart LR
MCU[MCU PWM L/R] --> A[U3: AND SAFE_A_OK]
A --> B[U4: AND SAFE_B_OK]
B --> C[U5: AND ALERT_N]
C --> MDD[MDD20A PWM L/R]
SA[12–16.8 V permissive A] --> OA[VO617A-4 A]
SB[12–16.8 V permissive B] --> OB[VO617A-4 B]
OA --> A
OB --> B
INA[Dual INA226 open-drain ALERT] --> C
REL[Safety relay] --> SA
REL --> SB
REL --> SW60[Normally-open main contactor]Both outputs follow:
PWM_OUT = LOGIC_POWER_OK AND PWM_IN AND SAFE_A_OK AND SAFE_B_OK AND ALERT_N
Either safety channel, a current ALERT, or loss of 3.3 V forces both PWM outputs low. DIR_L and DIR_R pass through directly and are not safety signals. The contract therefore requires MDD20A sign-magnitude mode, where PWM low is brake.
The board provides six declared test points: SAFE_A_OK, SAFE_B_OK, ALERT_N, PWM_L_OUT, PWM_R_OUT and GND. The PCB-plus-component envelope is 11.4 mm; including the 3.0 mm insulated mounting stack gives 14.4 mm installed height and only 0.6 mm analytical margin inside the Stage-18 keepout.
ALERT_N wire can be pulled high by R13; that path is not fail-safe. Commissioning must test the sensor harness and MCU freshness latch separately.engineering/stage19_dual_permissive_gate_contract.json — source-of-truth requirements and official references.engineering/stage19_gate_netlist.csv — pin-level connectivity contract.engineering/stage19_gate_bom.csv — provisional BOM; many passives remain manufacturer-TBD.engineering/stage19_gate_truth_table.csv — all 64 input combinations.engineering/stage19_dual_permissive_gate_results.json — analytical result and unresolved release gates.stage19_dual_permissive_gate.kicad_sch / .kicad_pro / .kicad_pcb — formal KiCad 10 schematic and routed two-layer PCB project.stage19_symbols.kicad_sym — project-local custom MCU-header and VO617A-4 symbols used by the deterministic capture.engineering/stage19_kicad_erc.json — KiCad 10.0.4 ERC export with zero violations.engineering/stage19_kicad_netlist.xml / stage19_kicad_bom.csv — machine-audited connectivity and KiCad BOM exports.engineering/stage19_kicad_pcb_drc.json — KiCad 10.0.4 PCB DRC report with zero violations and zero unconnected items.engineering/stage19_kicad_pcb_verification.json — structural regeneration, board envelope, mounting-hole, net and DRC evidence.output/pcb/BB8_stage19_gate_pcb_* — top/bottom copper review plots and a visually inspected isometric render; review images only, not Gerbers.output/pdf/BB8_stage19_dual_permissive_gate_schematic.pdf — reviewed one-page A4 schematic rendering.tools/verify_stage19_kicad.py — regenerates, runs ERC/exports and cross-audits the canonical netlist without granting fabrication release.tools/generate_stage19_kicad_pcb.py — deterministically places and routes the PCB with real KiCad footprints.tools/verify_stage19_kicad_pcb.py — regenerates the PCB in a temporary directory, compares UUID-independent structure and runs DRC on both copies.tools/export_stage19_kicad_pcb.py — exports review SVG/PNG files only; it cannot emit Gerber or drill manufacturing data.tools/verify_dual_permissive_gate.py — deterministic evaluator.board_envelope.scad — deterministic component-envelope model source. The local OpenSCAD 2021.01 CLI did not complete a headless export, so no STL is claimed in this stage.SAFE_A and SAFE_B independently.ALERT_N, logic-power loss and MCU stuck-high drive both PWM outputs low within 20 ms.| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 10.0k 1% | R_0805_2012Metric | R5, R6, R7, R8, R9, R10, R11, R12, R13 |
| 4 | M3 INSULATED | MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100nF | C_0603_1608Metric | C1, C2, C3 |
| 3 | SN74LVC2G08DCU | VSSOP-8_2.3x2mm_P0.5mm | U3, U4, U5 |
| 2 | 1N4148W | D_SOD-123 | D1, D2 |
| 2 | 2.00k 1% 0.5W | R_1210_3225Metric | R1, R2 |
| 2 | 4.70k 1% | R_0805_2012Metric | R3, R4 |
| 2 | VO617A-4 | DIP-4_W7.62mm | U1, U2 |
| 1 | ALERT_N | TestPoint_Loop_D2.50mm_Drill1.0mm | TP3 |
| 1 | GND | TestPoint_Loop_D2.50mm_Drill1.0mm | TP6 |
| 1 | LOGIC POWER 3V3 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | MCU PWM DIR ALERT | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J2 |
| 1 | MDD20A PWM DIR | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J3 |
| 1 | PWM_L_OUT | TestPoint_Loop_D2.50mm_Drill1.0mm | TP4 |
| 1 | PWM_R_OUT | TestPoint_Loop_D2.50mm_Drill1.0mm | TP5 |
| 1 | SAFE A 12-16V8 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | SAFE B 12-16V8 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | SAFE_A_OK | TestPoint_Loop_D2.50mm_Drill1.0mm | TP1 |
| 1 | SAFE_B_OK | TestPoint_Loop_D2.50mm_Drill1.0mm | TP2 |

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

pierrechevalier83/ferris
A low profile split keyboard designed to satisfy one single use case elegantly



MickiusMousius/Rolio46Keyboard
A split wireless keyboard based on the Corne and Sofle


sadekbaroudi/bgkeeb
This is a reversible 100mm x 100mm pcb with support for mx or choc switches (no hotswap), per key led, rotary encoders, and exposes the SDA/SCL/GND/VCC lines in the form of the pimoroni trackball pins (meaning you can…

It measures 50 × 35 mm and has 2 copper layers, 1.6 mm thick.
38 parts, built around the SN74LVC2G08DCU, VO617A-4 and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the zhangyinxina-ui/bb8-do-assembly-guide repository on GitHub, at the commit this page was made from: the board is hardware/stage19_dual_permissive_gate/stage19_dual_permissive_gate.kicad_pcb and its schematic hardware/stage19_dual_permissive_gate/stage19_dual_permissive_gate.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask zhangyinxina-ui before reusing the design.