Skip to the content

Boards using the NSG2065Q

9 boards

Boards in 8 GitHub repositories, designed in KiCad, that use the NSG2065Q by WXNSIC. See how each wires it, with its parts, size, README and files; the NSG2065Q’s symbol, footprint and pinout are on its own page.

  • 6 layers31.2 × 33 mm4in1-mini, the printed circuit board in 3D

    4in1-mini

    OpenDrone-hw/OpenESC-20x20

    Open-source 4-in-1 AM32 ESC for FPV drones. 20x20 mm, 2-6S, one MCU per motor, CERN-OHL-S-2.0.

    191 parts279CERN-OHL-S-2.0
  • 6 layers41.6 × 80.4 mm4in1-panel, the printed circuit board in 3D

    4in1-panel

    OpenDrone-hw/OpenESC-30x30

    Open-source 4-in-1 AM32 ESC for FPV drones. 30.5x30.5 mm, 2-8S, one MCU per motor, CERN-OHL-S-2.0.

    404 parts85CERN-OHL-S-2.0
  • 6 layers40.5 × 43 mmVENDETTAESC, the printed circuit board in 3D

    VENDETTAESC

    Caped-Crussader/VENDETTAFC

    A fully open-source, custom-designed 4-in-1 ESC and F7 Flight Controller stack for FPV multirotors, designed from scratch in KiCad.

    236 parts31CERN-OHL-S-2.0
  • 8 layers35 × 35 mmOpenAIO, the printed circuit board in 3D

    OpenAIO

    OpenDrone-hw/OpenAIO

    Open-source AIO for 2-6S toothpick quads: flight controller, 4-in-1 AM32 ESC and ExpressLRS receiver, 25.5x25.5 mm.

    343 parts19CERN-OHL-S-2.0
  • 6 layers28.3 × 28.3 mmEsc, the printed circuit board in 3D

    Esc

    cookiemonsternz/drone

    F \ish PV is a open source, custom stack, 75mm tinywhoop drone design. It utilises AM32 for the ESC firmware and Betaflight for the flight controller.

    141 parts5
  • 8 layers35 × 35 mmOpenAIO, the printed circuit board in 3D

    OpenAIO

    tetraethylmethane/NIDAR-RescueSwarm

    Three autonomous drones that search a flood zone, find survivors, geotag them, and drop medical kits — with no network, no pilot, and one operator who only presses start.

    285 parts1
  • 6 layers41.6 × 42.5 mm4in1, the printed circuit board in 3D

    4in1

    OliviezGit/OpenESC-30x30

    Open-source 4-in-1 BLDC ESC with a 30.5 × 30.5 mm mounting pattern, built around four independent AT32F421 motor controllers running AM32. Six-layer, DShot over the standard 8-pin connector.

    218 parts
  • 6 layers46.5 × 49 mmDreamscape ESC35A, the printed circuit board in 3D

    Dreamscape ESC35A

    sneakylizard123-4/Dreamscape-ESC35A

    203 parts
  • 6 layers41.6 × 42.5 mm4in1, the printed circuit board in 3D

    4in1

    OpenDrone-hw/OpenESC-30x30

    Open-source 4-in-1 AM32 ESC for FPV drones. 30.5x30.5 mm, 2-8S, one MCU per motor, CERN-OHL-S-2.0.

    222 parts85CERN-OHL-S-2.0