Skip to the content

Boards using the WIZ850IO

20 boards

Boards in 20 GitHub repositories, designed in KiCad, that use the WIZ850IO by WIZNET (10Mbps、100Mbps 132mA 2.97V~3.63V Short-Circuit Protection、Data encryption、Built-in signature detection、Thermal Protection、Overvoltage Protection Plugin,25x23mm Ethernet Modules ROHS). See how each wires it, with its parts, size, README and files; the WIZ850IO’s symbol, footprint and pinout are on its own page.

  • 2 layers69 × 43 mmDiagral uart esp32, the printed circuit board in 3D

    Diagral uart esp32

    nicolas5000/diagral-esp32

    This project permits to connect Home Assitant to your Diagral alarm system DIAG91AGFK (using the 20 pins connector on the back)

    12 parts6Apache-2.0
  • 2 layers90.3 × 72.8 mmRio tangbob, the printed circuit board in 3D

    Rio tangbob

    multigcs/rio-tangbob

    71 parts4
  • 2 layers50.4 × 50.4 mmBluepill ethernet, the printed circuit board in 3D

    Bluepill ethernet

    kellerkindt/bluepill_sensor

    Bluepill stm31f103 ethernet sensor extension board with SW written in Rust

    47 parts3Apache-2.0
  • 4 layers331.4 × 259.8 mmOvenMonESP32, the printed circuit board in 3D

    OvenMonESP32

    ThiSel18/OvenMonESP32CircuitBoard

    KiCad Project for Oven Monitoring

    6 parts1
  • 2 layers59.1 × 75.2 mmPico datalogger v4e, the printed circuit board in 3D

    Pico datalogger v4e

    bablokb/pcb-datalogger-v4e

    Pico Board for Data-Logging (Ethernet Version)

    27 partsCC-BY-SA-4.0
  • 2 layers50 × 50 mmHelix minimal, the printed circuit board in 3D

    Helix minimal

    flintwinters/helix-hardware

    KiCad 10 schematic for a USB powered STM32C071FBP6 with one shared SPI bus. The WIZ850io W5500 module and a 3.3 V, six wire microSD SPI breakout have separate chip selects. SWD is available for first firmware bring-up.

    20 parts
  • 2 layers80 × 80.5 mmF1c200s proj, the printed circuit board in 3D

    F1c200s proj

    JoachimBose/nabby-linux

    An Allwinner F1C100s / F1C200s buildroot external tree for (among others) the hardware challenge for VUCTF-2026

    68 partsGPL-2.0
  • 4 layers90 × 100 mmPCB Madre, the printed circuit board in 3D

    PCB Madre

    Jose-WaitNRest/PCB-Madre

    64 parts
  • 4 layers98.4 × 188.6 mmWNR MB SEDE1-PCB, the printed circuit board in 3D

    WNR MB SEDE1-PCB

    josevasquez123/WNR-MB-SEDE1-PCB

    190 parts
  • 2 layers103 × 86.5 mmVentilator, the printed circuit board in 3D

    Ventilator

    Kbij/VentControl

    Firmware for a custom made RP-2040 board with relays. Used for Ventilation control.

    79 parts
  • 2 layers160 × 60 mmCarrier, the printed circuit board in 3D

    Carrier

    ntotten/Kohler-DTV-Plus

    Replacement interface and CGI protocol analysis for the Kohler DTV+ shower system controller (K-99695-NA / K-99693-P-NA), plus an open investigation into mid-shower shutoffs.

    52 parts
  • 2 layers99.1 × 99.1 mmPicoHome2, the printed circuit board in 3D

    PicoHome2

    skmatik/picohomepcb

    Raspberry Pi Pico Home Automation - PCB

    36 parts
  • 2 layers100 × 92 mmBase station, the printed circuit board in 3D

    Base station

    yeyintlwin/kicad-board-design

    Design a two-layer KiCad PCB entirely from Python scripts - no GUI step, no commercial autorouter

    69 partsMIT
  • 2 layers235 × 160 mmInput output.Disk, the printed circuit board in 3D

    Input output.Disk

    lynchaj/duodyne

    Duodyne is a hobbyist retrocomputer system designed to run ROMWBW. It is comprised of modules on a system bus

    136 parts15
  • 2 layers160 × 100 mmScoring prototype board, the printed circuit board in 3D

    Scoring prototype board

    AndrewCraswell/agency

    Native KiCad engineering prototype, separate from the earlier ESP32/tscircuit board. Open usb-scoring-platform.kicadpro in KiCad 10; schematic and PCB are the editable source, with no generator required.

    43 partsMIT
  • 2 layersPlaca, the printed circuit board in 3D

    Placa

    nahucvc/Tejada

    4 parts
  • 2 layers99.1 × 76.2 mmVetrnik control, the printed circuit board in 3D

    Vetrnik control

    ondras12345/vetrnik

    Electronics for heating water with power from a 2 kW wind turbine

    87 parts