Skip to the content

Boards using the IS25LP128F-JBLE

11 boards

Boards in 9 GitHub repositories, designed in KiCad, that use the IS25LP128F-JBLE by ISSI (-40℃~+105℃ 100,000 cycles 128Mbit 166MHz 2.3V~3.6V 20 Years 200us 8uA Power-on reset、Hardware write protection、Software write protection、Write enable latch、Power lock protection SPI SOIC-8-208mil NOR FLASH ROHS). See how each wires it, with its parts, size, README and files; the IS25LP128F-JBLE’s symbol, footprint and pinout are on its own page.

  • 4 layers94 × 50.8 mmUlx3s, the printed circuit board in 3D

    Ulx3s

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    235 parts744MIT
  • 4 layers50 × 50 mmInsulin Pump PCB Schematic, the printed circuit board in 3D

    Insulin Pump PCB Schematic

    UCBioengineering/open_source_insulin_pump

    This repository contains software and hardware files for building an open source insulin pump. Files were created by the team at UC Bioengineering, University of Canterbury, Christchurch, New Zealand.

    143 parts27
  • 4 layers95 × 80 mmKilsyth, the printed circuit board in 3D

    Kilsyth

    kbeckmann/Kilsyth

    Errata: - C9 is not a GPIO on ECP5 F12 and some other variants. To get the LED working put a jumper on pin 31 and 33 on the Wide connector. - FTCLK is not routed to a clock pin.

    170 parts110BSD
  • 4 layers82.8 × 56.7 mmState Mode Logic Analyzer, the printed circuit board in 3D

    State Mode Logic Analyzer

    baldengineer/State-Mode-Logic-Analyzer

    RP2040-Based Logic Analyzer that captures "state" mode

    134 parts8MIT
  • 6 layers113 × 99 mmUlx4m panel, the printed circuit board in 3D

    Ulx4m panel

    intergalaktik/ulx4m-ls

    ULX4M Lattice SDRAM

    970 parts5
  • 4 layers97.6 × 74.8 mmProject byte hamr, the printed circuit board in 3D

    Project byte hamr

    robertrico/project_byte_hamr

    Open source expansion platform for Apple IIe prototyping and development

    93 parts2
  • 4 layers55.1 × 40 mmUlx4m backup, the printed circuit board in 3D

    Ulx4m backup

    NSfsfe/ulx4m

    PCB for ULX4M FPGA R&D board

    151 parts
  • 8 layers60.1 × 32.1 mmPanelith, the printed circuit board in 3D

    Panelith

    w531t4/panelith

    PCB for Panelith FPGA Board

    103 parts
  • 4 layers95 × 80 mmKilsyth, the printed circuit board in 3D

    Kilsyth

    kbeckmann/Kilsyth

    Errata: - C9 is not a GPIO on ECP5 F12 and some other variants. To get the LED working put a jumper on pin 31 and 33 on the Wide connector. - FTCLK is not routed to a clock pin.

    156 parts110BSD
  • 6 layers55.5 × 40.5 mmUlx4m, the printed circuit board in 3D

    Ulx4m

    intergalaktik/ulx4m-ls

    ULX4M Lattice SDRAM

    240 parts5