Skip to the content
2 layers30 × 49 mmI2c arduino lcd, the printed circuit board in 3D

I2c arduino lcd

voutti/board_fast_lcd

KiCad files for I2C LCD adapter board for HD44780 modules (1602 and 2004)

Size
30 × 49 mm
Copper layers
2
Thickness
1.6 mm
Parts
23
Nets
39
Pads
100
Tracks, vias
349, 51
Pours
89
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
14 May 2026
Updated
16 May 2026

Overview

I2c arduino lcd is an open-source printed circuit board by voutti, from the voutti/board_fast_lcd repository on GitHub, published under the MIT licence. It is a 2-layer board of 30 × 49 mm with 23 parts on 39 nets, routed with 349 tracks and 51 vias.

It is built around the ATMEGA328P-AU and S8050. Its parts include 6 capacitors, 6 resistors, 3 connectors, 1 IC and 1 transistor. It belongs with the lEDs and displays and interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

This is my attempt to replace the old PCF8574 or MCP23008 -based I2C to LCD adapters. The MCP23008 requires a ridiculous amount of I2C data to be written to output a character. PCF8574 based adapter is better but still requires 4 bytes for each character. This is not a problem with devices with fast I2C mastering capabilities but when, for example, bitbanging I2C with a slow CPU - this becomes quite slow.

In this adapter - the Atmel 328p is acting as a I2C slave and controls HD44780 based LCD via 4-bit interface. Firmware for the board as well as an example lib + test app for Commodore 64 (user port or cassette port) can be downloaded here: https://github.com/voutti/fast_lcd

Additionally I've added controlling the backlight which can also be put to "breathing" -mode via 328p PWM so, it does not load CPU of I2C master.

Notes:

  • 16MHz crystal is not needed
  • Solder bridges are available to enable I2C pull-ups if needed
  • It is fairly easy to program the 328p without soldering the J1 header just by holding it in place while programming.
  • By shorting JP4 when powering the board the firmware enters into test/demo -mode so, it is possible to test the board + LCD without I2C master.
  • RV1 is for adjusting the contrast of the LCD. I've used 10kohm trimmer since I had a lot of those (those blue square onces with 3 legs).
  • This design is for 5V based I2C master - it does not have level shifters for lower voltage operation.
i2c_lcd_back i2c_lcd_front i2c_lcd_assembled

Parts

23
QtyValueFootprintReferences
4SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP2, JP3, JP4
30.1uFPCM_JLCPCB:C_0603C2, C3, C6
210kPCM_JLCPCB:R_1206R1, R6
222pFPCM_JLCPCB:C_0603C4, C5
24.7kPCM_JLCPCB:R_1206R2, R3
110kConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalRV1
1120PCM_JLCPCB:R_1206R5
116MHzCrystal:Crystal_HC49-U_VerticalY1
11kPCM_JLCPCB:R_1206R4
14.7uFPCM_JLCPCB:C_0805C1
1ATmega328P-APackage_QFP:TQFP-32_7x7mm_P0.8mmU1
1Conn_01x04_SocketConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3
1Conn_01x16_SocketConnector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_VerticalJ2
1Conn_02x04_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_VerticalJ1
1S8050PCM_JLCPCB:Q_SOT-23Q1

Similar boards

  • 2 layers71.8 × 63.5 mmPlan b, the printed circuit board in 3D

    Plan b

    jwaeles/xmas-2019

    Dynamic christmas gift label that scrolls the name of the person it's for when you shake the gift

    152 parts3GPL-3.0
  • 2 layers109.3 × 45.4 mmAVR BRIDGE ATMEGA328P, the printed circuit board in 3D

    AVR BRIDGE ATMEGA328P

    MCLEANS/AVR-BRIDGE-ATMEGA328P-PCB

    PCB design for the AVR-BRIDGE ATMEGA328P test board

    55 parts1
  • 4 layers154 × 154 mmDC Controller STM32, the printed circuit board in 3D

    DC Controller STM32

    andymartell/Prius-STM32-DC-Motor-Contoller

    STM32 based DC Motor Controller using Prius Gen 3 hardware

    293 parts
  • 2 layers180 × 128 mmLeddriver, the printed circuit board in 3D

    Leddriver

    bitbyt3r/leddriver

    75 parts
  • 2 layers60 × 40 mmHASwitchPlate, the printed circuit board in 3D

    HASwitchPlate

    aderusha/HASwitchPlate

    LCD touchscreen for Home Automation

    16 parts738MIT
  • 10 layers224.5 × 160 mmHaasoscope pro adc fpga board, the printed circuit board in 3D

    Haasoscope pro adc fpga board

    drandyhaas/HaasoscopePro

    Affordable 2 GHz 3.2 GS/s 12 bit open-source open-hardware expandable USB real-time oscilloscope

    586 parts485MIT

Questions

How big is the I2c arduino lcd PCB?

It measures 30 × 49 mm and has 2 copper layers, 1.6 mm thick.

What parts does the I2c arduino lcd use?

23 parts, built around the ATMEGA328P-AU and S8050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the I2c arduino lcd KiCad files?

From the voutti/board_fast_lcd repository on GitHub, at the commit this page was made from: the board is i2c_arduino_lcd.kicad_pcb and its schematic i2c_arduino_lcd.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the I2c arduino lcd design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).