Skip to the content
4 layers65 × 56.5 mmCANopy, the printed circuit board in 3D

can hat design for raspberry pis

Size
65 × 56.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
42
Nets
65
Pads
180
Tracks, vias
441, 45
Pours
18
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Apr 2026
Updated
1 May 2026

Overview

CANopy is an open-source printed circuit board by taciturnaxolotl, from the taciturnaxolotl/CANopy repository on GitHub. It is a 4-layer board of 65 × 56.5 mm with 42 parts on 65 nets, routed with 441 tracks and 45 vias.

It is built around the MCP2562FD-E/SN and AT24C32N. Its parts include 14 capacitors, 9 resistors, 7 ICs, 4 connectors and 3 crystals.

Main components

2

README

README.md

CANopy

the main schematic the branch schematic

The canonical repo for this is hosted on tangled over at dunkirk.sh/CANopy

BOM

NamePurposeQuantityTotal Cost (USD)Distributor
2×20 40-pin stacking female header15-16mm pin length to clear Pi 5 active cooler, hand solder1$9.90Amazon
10kΩ 0603MCP2518FD RESET pull-up and MCP2562FD STBY pull-down, PCBA100$0.18LCSC
1kΩ 0603EEPROM write-protect pull-up to 3.3V, PCBA100$0.16LCSC
3.9kΩ 0603EEPROM SDA/SCL pull-ups to 3.3V, PCBA100$0.16LCSC
120Ω 0603CAN bus termination resistors, one per channel, PCBA100$0.09LCSC
10µF 0805Bulk caps for 3.3V and 5V rails, PCBA20$0.43LCSC
1µF 0603 X5RDecoupling caps for all ICs, PCBA100$0.56LCSC
15EDGRC-3.5-02P (plug & header)PCB-side right-angle pluggable terminal block, 3.5mm pitch, 2-pin, hand solder10$3.21LCSC
AT24C32D-SSHM-T32Kbit I2C EEPROM for HAT ID, SOIC-8, hand solder5$1.48LCSC
OVETGLJANF-40MHZ40MHz active oscillator, 3.3V, SMD5032-4P, hand solder11$6.14LCSC
MCP2562FDT-E/SNCAN FD transceiver with VIO pin, SOIC-8, hand solder11$12.87LCSC
MCP2518FDT-H/SLCAN FD SPI controller, SOIC-14, hand solder11$27.07LCSC

For use with the SystemCore the RSL can be emulated via the following

python
# pseudocode
gpio = /sys/class/gpio/gpioXX/value
while True:
  enabled = read("/sys/kernel/can_heartbeat/enabledro")
  gpio.write(enabled)
  # add blink pattern logic for disabled state
  sleep(0.05)

todo

  • add testpoints on i2c and can rx/tx 0.1" header
  • add termination resister jumper (dip switch block)
  • add rsl mosfet switching ground
  • 5v 5a pololu
  • new screw blocks DEGSON DG500-5.08-02P-14-00A(H)
  • esd diodes on the gpio pins for rsl
  • 120 ohm differential pairs for can

© 2026-present Kieran Klukas

Parts

42
QtyValueFootprintReferences
121µFCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12
310kΩResistor_SMD:R_0603_1608MetricR1, R4, R6
3120ΩResistor_SMD:R_0603_1608MetricR2, R3, R5
340MHZ OscillatorCrystal:Crystal_SMD_5032-4Pin_5.0x3.2mmY1, Y2, Y3
3LOGOLOGOduck-logo, first-logo, G***
3MCP2518FD-xQBBPCM_JLCPCB:SOIC-14_L8.7-W3.9-P1.27-LS6.0-BLU1, U3, U5
3MCP2562FD-E/SNPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU2, U4, U6
210µFCapacitor_SMD:C_0805_2012MetricC13, C14
23.9kΩResistor_SMD:R_0603_1608MetricR8, R9
11kΩResistor_SMD:R_0603_1608MetricR7
1AT24C32Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU7
1CAN0Degson:CONN-TH_DG500-5.08-02P-14-00A-HJ2
1CAN1Degson:CONN-TH_DG500-5.08-02P-14-00A-HJ3
1CAN2Degson:CONN-TH_DG500-5.08-02P-14-00A-HJ4
1OSHW-Logo2_7.3x6mm_SilkScreenSymbol:OSHW-Logo2_7.3x6mm_SilkScreenosh-hw
1RPi_GPIORPI_Hat:RPI_Hat_B+J1
1WriteProtect EnableTestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mmTP1

Similar boards

  • 2 layers65.5 × 98 mmFloppy Board v3.1, the printed circuit board in 3D

    Floppy Board v3.1

    FloppyO1/Floppy_Boards

    Floppy Boards are a series of breakout boards for rapid prototyping which I developed as an alternative of Arduino.

    339 parts5CERN-OHL-S-2.0
  • 2 layers65 × 56.5 mmPiFanIr, the printed circuit board in 3D

    PiFanIr

    llegoff/PiFanIrHat

    Raspberry pi HAT with fan and Ir receiver

    30 parts5
  • 4 layers94 × 72.8 mmMain board v2, the printed circuit board in 3D

    Main board v2

    BlueJayRacing/22xt_kicad

    As a summary, you should be using KiCad Version 9.0. All project will be modular, and you should be storing all your step files, symbols, & footprints within the created folders.

    163 parts
  • 4 layers66.7 × 66.2 mmSTM32G474 Dev v3, the printed circuit board in 3D

    STM32G474 Dev v3

    Rennaafi/stm32g474-dev-board

    4-layer STM32G474RE dev board (Nucleo-64 headers, USB-C, CAN-FD, STDC14) designed in KiCad 9: schematic, PCB layout, Gerbers & BOM

    77 partsMIT
  • 4 layers250 × 90 mmVCU V2, the printed circuit board in 3D

    VCU V2

    shutianx180/mk12-vcu-pcb

    366 parts
  • 8 layersFoc control, the printed circuit board in 3D

    Foc control

    sujaygouda123/foc-control

    BLDC field-oriented-control board for a humanoid robot actuator. KiCad 10, Ø80 mm, 8 layers, 1.6 mm.

    104 parts
  • 2 layers65 × 48 mmBarePi RTC, the printed circuit board in 3D

    BarePi RTC

    Panda381/BarePi

    Modular Microchip Kit

    15 parts4
  • 2 layers70 × 75 mmCloverpad mx, the printed circuit board in 3D

    Cloverpad mx

    Cloverpad/cloverpad-hardware

    Hardware designs for the Cloverpad, a 3-key keypad for osu!

    47 partsCERN-OHL-S-2.0

Questions

How big is the CANopy PCB?

It measures 65 × 56.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the CANopy use?

42 parts, built around the MCP2562FD-E/SN and AT24C32N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CANopy KiCad files?

From the taciturnaxolotl/CANopy repository on GitHub, at the commit this page was made from: the board is hardware/CANopy.kicad_pcb and its schematic hardware/CANopy.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CANopy design in my own project?

Its repository states no licence, so its author keeps all rights: ask taciturnaxolotl before reusing the design.