Skip to the content
2 layers82.8 × 160 mmPower, the printed circuit board in 3D

Modular laboratory power supply witch switched preregulator

Size
82.8 × 160 mm
Copper layers
2
Thickness
1.6 mm
Parts
115
Nets
83
Pads
353
Tracks, vias
704, 56
Pours
13
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
14 Apr 2025
Updated
14 Apr 2025

Overview

Power is an open-source printed circuit board by t0mka14, from the t0mka14/lab_supply repository on GitHub. It is a 2-layer board of 82.8 × 160 mm with 115 parts on 83 nets, routed with 704 tracks and 56 vias.

It is built around the ADS1015IDGS, IR2113S and MCP4728-E/UN, with the TPS60240DGK, ADUM7241ARZ and LM5035MH among its other parts. Its parts include 42 capacitors, 38 resistors, 11 ICs, 11 diodes and 3 connectors.

Main components

9

README

readme.md

Modular laboratory power supply with switched preregulator

This was one of my first large projects and also a subject of my diploma thesis back in 2020. At that time good and small multichannel laboratory power supplies were almost non existent, or at least I didn't know about any :D Therefore, we decided to build one. The transformer had to go and since 30V drop at 2A would burn any modest sized linear stabilizer, a switched preregulator followed by linear stabilizer was used. The output of the switched regulatoru would be always 1-2V above the set output voltage, ensuring good efficiency while having good dynamic parameters thanks to the linear stabilizer. One module contains two channels, 0-30V, 0-2A output each, galvanically isolated. You can find very detailed design procedure in my diploma thesis but it is in Czech...sorry 😅.

Table of Contents

Hardware

This project contains two PCBs, one is the actual power module and then there is a control panel assy. To be honest, the PCBs are not ideal, when I opened this project now, 5 years later, i see tons of posibilites for improvement.

Power PCB

The switched part is a half-bridge design controlled by LM5035 which is a voltage mode controller with line feed forward. 12V supply voltage comes from front assy. The transformer is classic half-bridge, custom wound on RM6 ferrite core. For the simplicity of design and because of relatively low ouptut curents, shotky diodes are used as rectifiers. Since the rectified input voltage is 320V, IR2113 is used as a high-side driver. The transformer: core

The linear part uses LT3086. It is a very nice IC, with current limit, current sensing, OV protection, thermal protection all easily coolable DPAK package. Only problem is, that is expects to be controlled by potentiometers, so we rigged it a bit with custom control circuit. Finally there are a few ICs for isolation and power for the secondary side.

Front assy

The front assy contains its own 12V power from small transformer, Arduino Nano, buttons, touch lcd display and relays for switching the ouput. It is supposed to fit one of those universal aluminium cases, which was used on this finished prototype: prototype

Measurements

One can find tons of measurements in the thesis, bellow are some which I used in defense presentation. I compared the measured values to Hantek HM7004 power supply. Check online how big and heavy that thing is. Also check how bad the dynamic parameters are. Measurements from the prototype are on the left, HM7004 on the right.

V mea 1 V mea 1

V mea 2 V mea 2

I mea 1 I mea 1

Parts

115
QtyValueFootprintReferences
10RResistor_SMD:R_0805_2012MetricR20, R23, R25, R26, R29, R33, R35, R36, R37, R38
61uCapacitor_SMD:C_0805_2012MetricC26, C27, C28, C32, C43, C46
30.1uCapacitor_SMD:C_0805_2012MetricC12, C13, C17
3100nCapacitor_SMD:C_1206_3216MetricC6, C7, C10
310nCapacitor_SMD:C_0805_2012MetricC2, C34, C45
31kResistor_SMD:R_0805_2012MetricR15, R22, R30
3CCapacitor_SMD:C_0805_2012MetricC38, C41, C42
3STPS2150ADiode_SMD:D_SMAD5, D6, D7
210Resistor_SMD:R_1206_3216MetricR12, R13
2100Resistor_SMD:R_0805_2012MetricR9, R10
2100uCapacitor_THT:CP_Radial_D16.0mm_P7.50mmC4, C5
210nCapacitor_SMD:C_1206_3216MetricC8, C9
210uCapacitor_SMD:C_0805_2012MetricC14, C21
210uCapacitor_SMD:C_1210_3225MetricC35, C44
2470pCapacitor_SMD:C_0805_2012MetricC22, C23
2510kResistor_SMD:R_1206_3216MetricR4, R5
25kResistor_SMD:R_0805_2012MetricR1, R2
27.5Resistor_SMD:R_1206_3216MetricR11, R14
2BLM31KN102SN1LDiode_SMD:D_1206_3216MetricFB1, FB2
2Conn_01x02Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_VerticalJ1, J4
2DDiode_SMD:D_SMAD8, D9
2D_SchottkyDiode_SMD:D_MiniMELFD3, D4
2D_ZenerDiode_SMD:D_MiniMELFD10, D11
2STD10NM60Package_TO_SOT_THT:TO-220-3_VerticalQ1, Q2
10Resistor_SMD:R_0805_2012MetricR31
10Resistor_SMD:R_1210_3225MetricR16
10.25uCapacitor_SMD:C_0805_2012MetricC20
1100uInductor_SMD:Coilcraft_J104L1
110kResistor_SMD:R_0805_2012MetricR34
110uCapacitor_SMD:CP_Elec_5x5.4C11
111800Resistor_SMD:R_0805_2012MetricR6
112kCapacitor_SMD:C_0805_2012MetricR7
1137nCapacitor_SMD:C_0805_2012MetricC29
11571Resistor_SMD:R_0805_2012MetricRmon1
11kResistor_SMD:R_1206_3216MetricR18
11nCapacitor_SMD:C_0805_2012MetricC33
12.2nCapacitor_SMD:C_0805_2012MetricC3
12.2uCapacitor_SMD:C_0805_2012MetricC24
1220kCapacitor_SMD:C_0805_2012MetricR24
122uCapacitor_SMD:CP_Elec_6.3x7.7C25
1280kResistor_SMD:R_1206_3216MetricR3
150uCapacitor_SMD:C_1210_3225MetricC36
1520 242Resistor_SMD:R_0805_2012MetricR27
158kResistor_SMD:R_0805_2012MetricR28
1680pCapacitor_SMD:C_0805_2012MetricC1
194.2kResistor_SMD:R_0603_1608MetricR19
19kResistor_SMD:R_0805_2012MetricR21
1ADS1015IDGSPackage_SO:TSSOP-10_3x3mm_P0.5mmU7
1ADuM7241Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU10
1CCapacitor_SMD:C_1206_3216MetricC37
1CCapacitor_SMD:C_1210_3225MetricC40
1C_FeedthroughCapacitor_SMD:C_0805_2012Metric_feedthroughtC31
1C_SmallCapacitor_SMD:C_0805_2012MetricC30
1CinCapacitor_SMD:C_1210_3225MetricC39
1Conn_01x09Connector_RJ:RJ45_Amphenol_RJHSE5380J2
1DNFCapacitor_SMD:C_1206_3216MetricR8
1D_SchottkyDiode_SMD:D_SMAD2
1Ferrite_BeadDiode_SMD:D_1206_3216MetricFB3
1IN+TestPoint:TestPoint_Pad_D1.5mmTP9
1IR2113SPackage_SO:SOIC-16W_7.5x10.3mm_P1.27mmU2
1LM5035Package_SO:LM5035U1
1LT3060Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.38mmU11
1LT3086_ddpakHeatsink:Heatsink_DDpak_AavidU8
1LT3092xSTPackage_TO_SOT_SMD:SOT-223-3_TabPin2U6
1MB8S_C53079Diode_SMD:BRIDGE_ONsemiD1
1MCP4728Package_SO:MSOP-10_3x3mm_P0.5mmU9
1OPA330xxDPackage_TO_SOT_SMD:SOT-23-5U5
1RResistor_SMD:R_0603_1608MetricR17
1RoutResistor_SMD:R_1206_3216MetricR32
1SFH617A-1Package_DIP:SMDIP-4_W7.62mmU3
1TPS60240Package_SO:VSSOP-8_3.0x3.0mm_P0.65mmU4
1TestPointTestPoint:TestPoint_Pad_D1.5mmTP7
1Transformer_1P_2STransformer_THT:RM6T1

Similar boards

  • 2 layers49 × 162.8 mmPower3, the printed circuit board in 3D

    Power3

    M-o-a-T/moat-hardware

    Schematics and files for MoaT IoT things

    95 parts
  • 2 layers203.2 × 130.8 mmRemoteHF, the printed circuit board in 3D

    RemoteHF

    mlanagan/RemoteHF

    Remote HF PCB and Node Red Website for WFView, SteppIRAntenna and Yeasu Rotator

    144 parts
  • 2 layers100 × 100 mmHF PA Radio Interface, the printed circuit board in 3D

    HF PA Radio Interface

    RADARC/Modular-PA-Controller

    Controller for High Power RF Power Amplifiers based Raspberry Pi Pico

    187 parts
  • 2 layers100 × 80 mmSmall drive, the printed circuit board in 3D

    Small drive

    mark-v-d/motor_control

    Motor controller with an XMC4400

    176 parts5
  • 4 layers146.1 × 55 mmStarGate MainBoard, the printed circuit board in 3D

    StarGate MainBoard

    plhsystems/stargate-mainboard-esp32

    Mainboard for Kristian's stargate projects, based on ESP32-S3

    171 parts4
  • 2 layers48.4 × 34.4 mmMpptDemoBoard, the printed circuit board in 3D

    MpptDemoBoard

    Cubesat-EPS-Project/EPS_Demo_MPPTboard

    Demo pcb board for MPPT

    22 parts
  • 4 layers95.1 × 95.1 mmFinal eps pcb 4layer, the printed circuit board in 3D

    Final eps pcb 4layer

    Cubesat-EPS-Project/final_eps_pcb_4layer

    186 partsGPL-3.0

Questions

How big is the Power PCB?

It measures 82.8 × 160 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Power use?

115 parts, built around the ADS1015IDGS, IR2113S, MCP4728-E/UN and TPS60240DGK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Power KiCad files?

From the t0mka14/lab_supply repository on GitHub, at the commit this page was made from: the board is power/power.kicad_pcb and its schematic power/file5F2EA221.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Power design in my own project?

Its repository states no licence, so its author keeps all rights: ask t0mka14 before reusing the design.