

Wio e5-test
- Size
- 35.1 × 33.5 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 31
- Nets
- 34
- Pads
- 138
- Tracks, vias
- 243, 145
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 Jul 2025
- Updated
- 1 Jul 2025
Overview
Wio e5-test is an open-source printed circuit board by sigmondkukla, from the sigmondkukla/wio-e5-test repository on GitHub. It is a 4-layer board of 35.1 × 33.5 mm with 31 parts on 34 nets, routed with 243 tracks and 145 vias.
It is built around the WIO-E5, LPS22HH and MIC5318-3.3YD5-TR. Its parts include 9 capacitors, 7 resistors, 6 connectors, 3 ICs and 3 switches.
Main components
3WIO-E5
SMD,12x12mmSMD,12x12mm LoRa Modules ROHSSeeedLoRa ModulesLPS22HH
HLGA-10(2x2)-40℃~+85℃ 0.025hpa 0.5hpa 1.7V~3.6V 26Kpa~1.26bar 900nA I2C、SPI On-chip temperature compensation、Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Integrated signal amplifier、On-chip temperature output HLGA-10(2x2) Pressure Sensors ROHSSTMicroelectronicsPressure SensorsMIC5318-3.3YD5-TR
TSOT-23-5-40℃~+125℃@(Tj) 1 110mV@(300mA) 3.3V 300mA 30uVrms 6V 75dB@(1kHz) 85uA Fixed Over Current Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
31| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C1, C3, C4, C6 |
| 3 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C5, C9 |
| 3 | 470 | Resistor_SMD:R_0603_1608Metric | R1, R4, R5 |
| 3 | PTS815 | PTS815_SJM_250_SMTR_LFS:SW_Push_PTS815_SJM_250_SMTR_LFS | SW1, SW2, SW3 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R6, R7 |
| 2 | DNP | Capacitor_SMD:C_0603_1608Metric | C7, C8 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D2 |
| 1 | 0 | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | Conn_01x04_Qwiic | BM04B-SRSS-TB:CONN_JST-BM04B-SRSS-TB | J6 |
| 1 | Conn_01x09_Pin | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J7 |
| 1 | Conn_01x13_Pin | Connector_PinHeader_2.54mm:PinHeader_1x13_P2.54mm_Vertical | J4 |
| 1 | Cortex | 3220-10-0100-00_CNC:CONN_3220-10-0100-00_CNC | J3 |
| 1 | DNP | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | JST PH 2.0 | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal_Reverse_Polarity:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1 |
| 1 | LPS22HH | Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y | U2 |
| 1 | MIC5318-3.3YD5 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | SMA | Connector_Coaxial:SMA_Samtec_SMA-J-P-H-ST-EM1_EdgeMount | J5 |
| 1 | Wio-E5 | Wio-E5:Wio-E5 | U3 |
Similar boards
- 4 layers100 × 80 mm

- 2 layers50 × 45 mm

PowerCutoffBoard1
ararobo/GN10RemoteEmergencyStop
PowerCutoffBoard and RemoteSwitchBoard created by Gento Aiba.
46 parts1 - 4 layers50 × 30 mm

Cc1200-balloon
tmpk13/cc1200-balloon
High altitude balloon payload: a CC1200 sub-GHz telemetry downlink and an air quality sensor stack, hosted by a Seeed Wio-E5 module. Four-layer 50 x 30 mm board, routed.
108 partsMIT - 4 layers40 × 40 mm

- 4 layers50.8 × 20.3 mm

Iceblink
bminch/iceBlinkPico
Design files and SystemVerilog examples for iceBlinkPico, a small breadboard-friendly iCE40UP5K FPGA dev board
57 parts2BSD-2-Clause - 4 layers30.5 × 27 mm

Trustflight hardware
korken89/trustflight_hardware
A small and simple flight controller to be used with the trustflight firmware flight controller firmware, which is focusing on safety by using the Rust programming language.
69 parts1 - 2 layers32.2 × 52.2 mm

ICE40UP5Kdev
redhotchili0909/engr3430-eclectronics
Through a series of projects, students will learn all aspects of printed-circuit board (PCB) design at the prototype scale of manufacturing, including electronic circuit/system design, component selection, schematic…
53 partsMIT - 2 layers21.8 × 51.9 mm

Questions
How big is the Wio e5-test PCB?
It measures 35.1 × 33.5 mm and has 4 copper layers, 1.61 mm thick.
What parts does the Wio e5-test use?
31 parts, built around the WIO-E5, LPS22HH and MIC5318-3.3YD5-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wio e5-test KiCad files?
From the sigmondkukla/wio-e5-test repository on GitHub, at the commit this page was made from: the board is wio-e5-test.kicad_pcb and its schematic wio-e5-test.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wio e5-test design in my own project?
Its repository states no licence, so its author keeps all rights: ask sigmondkukla before reusing the design.